Sony DVP-NS308 / DVP-NS38 / DVP-NS39 Service Manual ▷ View online
2-2
DVP-NS38/NS39/NS308
2-3. LOADING ASSEMBLY
b
6
Three Screws
+BV3
(3-CR)
7
Loading Assembly
1
FMO-013 Flat Flexible Cable (CN101, 24P)
3
FMS-015 Flat Flexible Cable (CN202, 5P)
2
MD-119 Harness (CN201, 6P)
b
a
5
PM-136 Harness
(CN201,
10P)
4
PM-136 Harness (CN501, 10P)
a
2-3
DVP-NS38/NS39/NS308
2-4. OPTICAL PICK-UP
(DEVICE, OPTICAL KHM-313CAA/C2RP)
Caution Point on the Laser Diode:
Laser Diode in the optical Device is very sensitive to Surge Current
or ElectroStatic Discharge (ESD):
Laser Diode in the optical Device is very sensitive to Surge Current
or ElectroStatic Discharge (ESD):
After take-out FMO-013 Flat Flexible Cable from CN101 of
MV-58 board immediately ground FMO-013 Flat Flexible Cable
pattern using short clip. Metal paper clip can be used as short
clip.
MV-58 board immediately ground FMO-013 Flat Flexible Cable
pattern using short clip. Metal paper clip can be used as short
clip.
5
FMO-013 Flat Flexible Cable (CN101, 24P)
4
MD-119 Harness (CN201, 6P)
1
Four Insulator Screws
6
Two Insulator
6
Two Insulator
3
Optical Device
(KHM-313CAA/C2RP)
2
FFC Holder
Shortland Position
Note:
Solder shortland before remove the
FMO-013 Flat Flexible Cable from
24 pin BU connector.
FMO-013 Flat Flexible Cable from
24 pin BU connector.
The components identified by
mark or dotted line with mark
mark or dotted line with mark
are critical for safety.
Replace only with part number
specified.
specified.
2-4
DVP-NS38/NS39/NS308
2-5. REAR PANEL, MV-58 BOARD and IF-156 BOARD
7
FMO-013 Flat Flexible Cable
(CN101,
24P)
6
FMS-015 Flat Flexible Cable
(CN202,
5P)
7
FMO-013 Flat Flexible Cable
(CN101,
24P)
9
FIM-019 Flat Flexible Cable
(CN401,
23P)
6
FMS-015 Flat Flexible Cable
(CN202,
5P)
qa
MV-058 Board
qa
MV-058 Board
5
MD-119 Harness
(CN201,
6P)
5
MD-119 Harness
(CN201,
6P)
8
PM-136 Harness
(CN501,
10P)
q;
Three Screws
+BV3
(3-CR)
q;
Three Screws
+BV3
(3-CR)
2
One Screw
+B
3x3
3
One Tapping Screw
4
Rear Panel
1
One Screw
+BV3(3-CR)
2
One Screw
+B
3x3
3
One Tapping Screw
1
One Screw
+BV3(3-CR)
qd
IF-156 Board
8
PM-136 Harness
(CN501,
10P)
4
Rear Panel
qs
Two Screws
+BV3
(3-CR)
c
c
o
c
a
a
l
p
o
l
p
DVP-NS307/NS308
DVP-NS308
DVP-NS38/NS39
DVP-NS38/NS39
a
Note:
Caution Point on the PWB IF-156
Caution Point on the PWB IF-156
When handling IF-156 PWB avoid contact with
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND401).
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND401).
2-5
DVP-NS38/NS39/NS308
2-6. SWITCHING REGULATOR
2
Two Screws
+BV3
(3-CR)
1
Connector
(PM-136
Harness,
CN201,
10P)
3
Power Board
Click on the first or last page to see other DVP-NS308 / DVP-NS38 / DVP-NS39 service manuals if exist.