Sony DVP-NC65K / DVP-NC66K Service Manual ▷ View online
2-4
DVP-NC65K/NC66K
2-7. IF-148 BOARD
1
FIS-004 Flat Flexible Cable
(CN504,
9P)
7
FM-100 Harness
(CN404,
11P)
Two Screws
+BVTP2.6 (3CR)
+BVTP2.6 (3CR)
4
Two Screws
+BV3
(3-CR)
6
FIM-008 Flat Flexible Cable
(CN401,
23P)
5
FIM-016 Flat Flexible Cable
(CN403,
5P)
8
FIS-004 Flat Flexible Cable
(CN407,
9P)
9
FLD
3
Table Assy
2
Front Panel
0
IF-148 Board
Note:
Caution Point on the PWB IF-148
When handling IF-148 PWB avoid contact with
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND401).
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND401).
2-5
DVP-NC65K/NC66K
2-8. LOADING MOTOR ASS’Y
Loading motor assembly
(M901)
(M901)
Table
Belt (timing)
Screw
(M2.6x4) (3CR)
(M2.6x4) (3CR)
Screw
(M2.6x4) (3CR)
(M2.6x4) (3CR)
Claws
Claw
MD-105 Board
ML-068 Harness
(CN004, 2P)
(CN004, 2P)
2-6
DVP-NC65K/NC66K
2-9. OPTICAL PICK-UP
(DEVICE, OPTICAL KHM-313CAB/C2RP)
Caution Point on the Laser Diode:
Laser Diode in the optical Device is very sensitive to Surge Current or
ElectroStatic Discharge (ESD):
Laser Diode in the optical Device is very sensitive to Surge Current or
ElectroStatic Discharge (ESD):
After take-out FMO-006 Flat Flexible Cable from CN101 of
MV-51 board immediately ground FMO-006 Flat Flexible Cable
pattern using short clip. Metal paper clip can be used as short
clip.
MV-51 board immediately ground FMO-006 Flat Flexible Cable
pattern using short clip. Metal paper clip can be used as short
clip.
Shortland Position
Note:
Solder shortland before remove the
FMO-006 Flat Flexible Cable from
24 pin BU connector.
FMO-006 Flat Flexible Cable from
24 pin BU connector.
5
FMO-006 Flat Flexible Cable
(24P)
4
MD-117 Harness
(6P)
6
Optical Pick-Up
3
Four Insulator Screws
2
FFC Holder
1
FFC Clamp
Caution Point on the Harness Dressing:
Please make sure MD117 Harness (black tapping) always before
hook during assembly. Refer to Fig. 1.
Please make sure MD117 Harness (black tapping) always before
hook during assembly. Refer to Fig. 1.
Black Tapping
Hook
Fig. 1.
2-7
DVP-NC65K/NC66K
2-10. POWER BLOCK
2
Two Screws
+BV3
(3-CR)
3
Two Claws
Holder, PS
4
Power Block
1
PM-131 Harness
(CN201,
10P)
Power Cord
2-11. FR-251, SW-477 and MC-163 BOARDS
3
Three Screws +BV2.6 (3-CR)
4
Screw +BV2.6 (3-CR)
5
MC-163 Board
Front Panel
Cover tray
1
FIS-004 Flat Flexible Cable
(CN504,
9P)
SW-477 Board
6
FR-251 Board
2
Five Screws +BV2.6 (3-CR)
Click on the first or last page to see other DVP-NC65K / DVP-NC66K service manuals if exist.