DOWNLOAD Sony DVP-NC65K / DVP-NC66K Service Manual ↓ Size: 6.4 MB | Pages: 89 in PDF or view online for FREE

Model
DVP-NC65K DVP-NC66K
Pages
89
Size
6.4 MB
Type
PDF
Document
Service Manual
Brand
Device
DVD
File
dvp-nc65k-dvp-nc66k.pdf
Date
PREV: Sony DVP-NC85H / HT-7000DH Service Manual

Sony DVP-NC65K / DVP-NC66K Service Manual ▷ View online

1-20
DVP-NC65K/NC66K
79
Additional Informati
on
Specifications
System
Laser: Semiconductor laser
Signal format system: PAL/NTSC (See 
page 16 to switch)
Audio characteristics
Frequency response: DVD VIDEO (PCM 
96 kHz): 2 Hz to 44 kHz (±1.0 dB)/DVD 
VIDEO (PCM 48 kHz): 2 Hz to 22 kHz 
(±0.5 dB)/CD: 2 Hz to 20 kHz (±0.5 dB)
Signal-to-noise ratio (S/N ratio): 115 dB 
(LINE OUT L/R (AUDIO) jacks only)
Harmonic distortion: 0.003 %
Dynamic range: DVD VIDEO: 103 dB/
CD: 99 dB
Wow and flutter: Less than detected value 
(±0.001% W PEAK)
Outputs and Input
(Jack name: Jack type/Output level/Load 
impedance)
LINE OUT (AUDIO): Phono jack/2 Vrms/
10 kilohms
DIGITAL OUT (OPTICAL): Optical 
output jack/–18 dBm (wave length 
660 nm)
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
COMPONENT VIDEO OUT (Y, P
B
/C
B
,
P
R
/C
R
): Phono jack/Y: 1.0 Vp-p, P
B
/C
B
,
P
R
/ C
R
: 0.7 Vp-p/75 ohms
LINE OUT (VIDEO): Phono jack/1.0 Vp-p/
75 ohms
S VIDEO OUT: 4-pin mini DIN/Y:1.0 Vp-p, 
C: 0.3 Vp-p (PAL), 0.286 Vp-p (NTSC)/
75 ohms
MIC Input 1/2: Phone jacks
General
Power requirements:
110 – 240 V AC, 50/60 Hz
Power consumption: 11 W
Dimensions (approx.):
430 
×  83 ×  416 mm
(16
15
/
16
×  3 
17
/
64
×  16 
24
/
64
 in.) (width/
height/depth) incl. projecting parts
Mass (approx.): 4.4 kg (9 
58
/
64
 lb)
Operating temperature: 5
° C to 35 ° C
Operating humidity: 25 % to 80 %
Supplied accessories
See page 14.
Specifications and design are subject to 
change without notice.
E
NERGY 
S
TAR
R
 is a U.S. registered mark. 
As an 
E
NERGY 
S
TAR
R
 Partner, Sony 
Corporation has determined that this product 
meets the 
E
NERGY 
S
TAR
R
 guidelines for 
energy efficiency.
1-20E
2-1
DVP-NC65K/NC66K
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY
SECTION 2
DISASSEMBLY
NOTE: Follow the disassembly procedure in the numerical order given.
2-2. UPPER CASE
Loading Motor Ass’y
(Page 2-5)
Optical Pick-Up 
(Page 2-6)
Front Panel Section
(Page 2-2)
Rear Panel Section
(Page 2-3)
MV-51Board
(Page 2-3)
Table Ass’y
(Page 2-2)
IF-148 Board
(Page 2-4)
Power Block
(Page 2-7)
FR-251, SW-477 and  
MC-163 Boards
(Page 2-7)
Upper Case
(Page 2-1)
Set
3
 Hook
4
 Upper Case
Hameron Tape
1
 Two Tapping Screws
2
 Three Screws
 +BV3 
(3-CR)
2-2
DVP-NC65K/NC66K
2-3. FRONT PANEL SECTION
a
Two Screws
+BV3 (3-CR)
6
 Front Panel Section
2
 FIS-004 Flat Flexible Cable
 (CN407, 
9P)
IF-148 PWB
Connector
(CN201)
3
1 
PM-131 Harness
 (CN501, 
8P)
a
5
 Claw
4
 Claw
2-4. TABLE ASS’Y
Display Filter
a
a
5
 MD-117 Harness
 (CN201, 
6P)
7
 FM-100 Harness
 (CN404, 
11P)
6
 PM-131 Harness
 (CN501, 
10P)
4
 FMO-006 Flat Flexible Cable
 (CN101, 
24P)
9
 Table Assembly
2
 Four Screws
 
+BV3  (3CR)
3
 PM-131 Harness
 (CN201, 
10P)
8
 PM-131 Harness
 (CN501, 
8P)
Insert a flat-head (-) screwdriver into a hole at the bottom,
the cam gear in the direction of the arrow A.
A
1
Note:
Before remove FMO-006
Flat Flexible Cable,
please follow point at page 2-6.
2-3
DVP-NC65K/NC66K
2-5. REAR PANEL SECTION
1
2
 Four Screws +BV3 (3-CR)
3
 Rear Panel
2-6. MV-51 BOARD
a
b
8
 FMO-006 Flat Flexible Cable
 (CN101, 
24P)
4
 Harness PM-131
 (CN501, 
10P)
q;
 Harness PM-131 (CN404, 8P)
7
 FIM-008 Flat Flexible Cable
 (CN107, 
23P)
6
  FIM-016 Flat Flexible Cable
 (CN202, 
5P)
2
  Pull the tray in the  
 
direction of the arrow B
B
5
 MD-117 Harness
 (CN201, 
6P)
9
 MV-51 Board
3
 Five Screws BV3 (3-CR)
a
Note:
Before remove FMO-006
Flat Flexible Cable,
please follow point at page 2-6.
Caution A:
A 
Insert a flat-head (-) screwdriver into a hole at the bottom,
 
the cam gear in the direction of the arrow A.
1
Page of 89
Display

Click on the first or last page to see other DVP-NC65K / DVP-NC66K service manuals if exist.

RANDOM: