Sony DVP-NC600 Service Manual ▷ View online
1-5
23
Hookups
COAXIAL
DIGITAL OUT
PCM/DTS/
DOLBY DIGITAL
DOLBY DIGITAL
OPTICAL
S VIDEO
OUT
COMPONENT
VIDEO OUT
Y
P
B
1
2
P
R
LINE OUT
VIDEO
R – AUDIO – L
B-2
B-1
COAXIAL
DIGITAL OUT
PCM/DTS/
DOLBY DIGITAL
DOLBY DIGITAL
OPTICAL
R – AUDIO – L
VIDEO
1
2
LINE OUT
l
: Signal flow
CD/DVD player
or
Stereo amplifier (receiver)
MD deck/DAT deck
Front
(L)
Front
(R)
[Speakers]
(white)
(red)
to coaxial or optical digital input
Coaxial digital cord
(not supplied)
(not supplied)
Stereo audio cord
(not supplied)
(not supplied)
to audio input
(white)
(red)
Optical digital cord (not supplied)
Remove jack cap before
connecting.
Remove jack cap before
connecting.
or
24
This connection will allow you to enjoy the surround effects of the Pro Logic decoder on your
amplifier (receiver). If you have an AV amplifier (receiver) equipped with a Dolby Digital or
DTS decoder, refer to page 26.
You can enjoy the Dolby Surround effects only when playing Dolby Surround audio or
multichannel audio (Dolby Digital) discs.
Pro Logic uses a minimum of 3 speakers (front L and R, and rear (monaural)). The surround
effects are enhanced if 6 speakers (front L and R, center, rear L and R, and subwoofer) are used.
If your amplifier (receiver) has R and L audio input jacks only, use
amplifier (receiver). If you have an AV amplifier (receiver) equipped with a Dolby Digital or
DTS decoder, refer to page 26.
You can enjoy the Dolby Surround effects only when playing Dolby Surround audio or
multichannel audio (Dolby Digital) discs.
Pro Logic uses a minimum of 3 speakers (front L and R, and rear (monaural)). The surround
effects are enhanced if 6 speakers (front L and R, center, rear L and R, and subwoofer) are used.
If your amplifier (receiver) has R and L audio input jacks only, use
. If your amplifier
(receiver) has a digital input jack, use
.
xRecommended surround sound effects using this connection with your amplifier (receiver).
• Dolby Surround (Pro Logic) (page 66)
z
For correct speaker setting location, please refer to the operating instructions of the amplifier (receiver).
Connecting to a Dolby Surround (Pro Logic) decoder amplifier (receiver) and
3 to 6 speakers
C
C-1
C-2
25
Hookups
* When connecting 6 speakers, replace the monaural rear speaker with a center speaker, 2 rear speakers and a
subwoofer.
COAXIAL
DIGITAL OUT
PCM/DTS/
DOLBY DIGITAL
DOLBY DIGITAL
OPTICAL
S VIDEO
OUT
COMPONENT
VIDEO OUT
Y
P
B
1
2
P
R
LINE OUT
VIDEO
R – AUDIO – L
C-2
C-1
COAXIAL
DIGITAL OUT
PCM/DTS/
DOLBY DIGITAL
DOLBY DIGITAL
OPTICAL
R – AUDIO – L
VIDEO
1
2
LINE OUT
CD/DVD player
or
Front
(R)
Front
(L)
Rear
(R)
Subwoofer
l
: Signal flow
Rear
(L)
Dolby Surround amplifier (receiver)
Center
Rear
*
(mono)
[Speakers]
to coaxial or
optical digital
input
optical digital
input
Coaxial digital cord
(not supplied)
(not supplied)
Stereo audio cord
(not supplied)
(not supplied)
to audio input
(white)
(red)
[Speakers]
Optical digital cord (not supplied)
Remove jack cap before
connecting.
Remove jack cap before
connecting.
or
(red)
(white)
26
This connection will allow you to use the Dolby Digital or DTS decoder function of your AV
amplifier (receiver). You are not able to enjoy the TVS sound effects of the player.
amplifier (receiver). You are not able to enjoy the TVS sound effects of the player.
xRecommended surround sound effects using this connection with your amplifier (receiver).
• Dolby Digital (5.1ch) (page 66)
• DTS (5.1ch) (page 66)
z
To enhance the surround sound effects, refer to the operating instructions of the amplifier (receiver) for correct
speaker setting location.
After you have completed the connection, be sure to set “DOLBY DIGITAL” to “DOLBY DIGITAL” (page 30). If
your AV amplifier (receiver) has a DTS decoder, set “DTS” to “ON” (page 30). Otherwise, no sound or a loud noise
will come from the speakers.
your AV amplifier (receiver) has a DTS decoder, set “DTS” to “ON” (page 30). Otherwise, no sound or a loud noise
will come from the speakers.
Connecting to an AV amplifier (receiver) with a digital input jack having a
Dolby Digital or DTS decoder, and 6 speakers
Note
D
1-6
27
Hookups
COAXIAL
DIGITAL OUT
PCM/DTS/
DOLBY DIGITAL
DOLBY DIGITAL
OPTICAL
S VIDEO
OUT
COMPONENT
VIDEO OUT
Y
P
B
1
2
P
R
LINE OUT
VIDEO
R – AUDIO – L
COAXIAL
DIGITAL OUT
PCM/DTS/
DOLBY DIGITAL
DOLBY DIGITAL
OPTICAL
D
Front
(R)
Front
(L)
Rear
(R)
Rear
(L)
AV amplifier (receiver) with a decoder
Subwoofer
Center
[Speakers]
[Speakers]
Coaxial digital cord
(not supplied)
(not supplied)
to optical digital input
l
: Signal flow
CD/DVD player
Optical digital cord
(not supplied)
(not supplied)
to coaxial digital input
Remove jack
cap before
connecting.
cap before
connecting.
or
28
Step 3: Connecting the Power Cord
Plug the player and TV power cords into an AC outlet.
Do not connect the power cord of your player to the “switched” power socket of an amplifier
(receiver). Otherwise, when you turn off the power of your amplifier (receiver), the settings for
the player may be lost.
(receiver). Otherwise, when you turn off the power of your amplifier (receiver), the settings for
the player may be lost.
Step 4: Quick Setup
Follow the steps below to make the minimum number of basic adjustments to use the player. To
skip an adjustment press
skip an adjustment press
>, to return to the previous adjustment, press ..
A Turn on the TV.
B Switch the input selector on the TV to the player.
C Press POWER on the player and press ?/1 on the remote
.
“Press [ENTER] to run QUICK SETUP.” appears at the bottom of the screen. If this message
does not appear, select “QUICK” under SETUP in the Control Menu (page 14) to run Quick
Setup.
does not appear, select “QUICK” under SETUP in the Control Menu (page 14) to run Quick
Setup.
1
4
7
2
5
8
0
3
6
9
ENTER
POWER
X/x
?/1
X/x
ENTER
./>
./>
29
Hookups
D Press ENTER without inserting a disc.
The Setup Display for selecting the language used in the on-screen display appears.
E Press X/x to select a language.
The player uses the language selected here to display the DVD menu and subtitles as well.
F Press ENTER.
The Setup Display for selecting the aspect ratio of the TV to be connected appears.
G Press X/x to select the item.
H Press ENTER.
The Setup Display for selecting the type of jack used to connect your amplifier (receiver)
appears.
appears.
TV Type
You select
Page
4:3 standard TV
4:3 LETTER BOX or 4:3 PAN
SCAN
SCAN
64
A wide-screen TV or 4:3 standard TV with
the wide-screen mode
the wide-screen mode
16:9
64
LANGUAGE SETUP
OSD:
DVD MENU:
AUDIO:
SUBTITLE:
DVD MENU:
AUDIO:
SUBTITLE:
FRENCH
ENGLISH
ENGLISH
ENGLISH
SPANISH
PORTUGUESE
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
SCREEN SAVER:
BACKGROUND:
4:3 PAN SCAN
4:3 LETTER BOX
16:9
4:3 LETTER BOX
YES
NO
Is this player connected to an amplifier
(receiver) ? Select the type of jack you
are using.
(receiver) ? Select the type of jack you
are using.
LINE OUTPUT L/R (AUDIO)
DIGITAL OUTPUT
continued
,
30
I Press X/x to select the item, then press ENTER.
• When “NO” or “LINE OUTPUT L/R (AUDIO)” is selected, Quick Setup is finished and
connections are complete.
• When “DIGITAL OUTPUT” is selected, the Setup Display for “DOLBY DIGITAL”
appears. Proceed to Step 0.
J Press X/x to select the item.
Choose the item that matches the audio connection you selected in pages 22 to 26 (
through ).
K Press ENTER.
DTS is selected.
L Press X/x to select the item.
Choose the item that matches the audio connection you selected in pages 22 to 26 (
through ).
Audio Cord Connection Type
You select
Page
D-PCM
68
DOLBY DIGITAL (only if the
amplifier/receiver has a Dolby
Digital decoder)
amplifier/receiver has a Dolby
Digital decoder)
68
Audio Cord Connection Type
You select
Page
OFF
68
ON (only if the amplifier/receiver
has a DTS decoder)
has a DTS decoder)
68
B
D
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
AUDIO DRC:
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
OFF
STANDARD
ON
DOWNMIX:
DOLBY SURROUND
DOLBY DIGITAL
D-PCM
D-PCM
B-2
C-2
D
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
AUDIO DRC:
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
DTS:
OFF
STANDARD
ON
DOWNMIX:
DOLBY SURROUND
D-PCM
OFF
OFF
OFF
ON
B
D
B-2
C-2
D
1-7
31
Hookups
M Press ENTER.
Quick Setup is finished. All connections and setup operations are complete.
You can directly start Quick Setup only when you run it for the first time.
To run Quick Setup a second time, select “QUICK” under SETUP in the Control Menu (page 62).
To run Quick Setup a second time, select “QUICK” under SETUP in the Control Menu (page 62).
To enjoy the surround sound effects of this player or your amplifier (receiver), the following
items must be set as described below for the audio connection you selected in pages 22 to 26
(
items must be set as described below for the audio connection you selected in pages 22 to 26
(
through
). Each of these are the default settings and do not need to be adjusted when
you first connect the player. Refer to page 62 for using the Setup Display.
Audio Connection (pages 21 to 26)
No additional settings are needed.
• If the sound distorts even when the volume is turned down, set “AUDIO ATT” to “ON” (page
66).
Note
Enjoying the surround sound effects
Item
You select
Page
DOWNMIX
DOLBY SURROUND
67
Item
You select
Page
DOWNMIX
DOLBY SURROUND
67
DIGITAL OUT
ON
67
B
D
A
B-1
C-1
B-2
C-2
D
32
Playing Discs
Playing Discs
Depending on the DVD or VIDEO CD, some
operations may be different or restricted.
operations may be different or restricted.
Refer to the operating instructions supplied
with your disc.
with your disc.
1
Turn on your TV.
2
Switch the input selector on the TV
to the player.
to the player.
When using an amplifier (receiver)
Turn on the amplifier (receiver) and
select the appropriate channel.
Turn on the amplifier (receiver) and
select the appropriate channel.
3
Press POWER on the player.
The player enters standby mode and the
power indicator lights up in red.
power indicator lights up in red.
4
Press
A on the player, and place a
disc on the disc tray.
The player automatically turns on and the
power indicator lights up in green.
To place other discs on the tray, press
DISC SKIP and place the discs in the
order you want to play them.
Each time you press DISC SKIP, the disc
tray turns so you can place the discs on
the empty compartments. The player
plays from the last disc placed on the
tray.
power indicator lights up in green.
To place other discs on the tray, press
DISC SKIP and place the discs in the
order you want to play them.
Each time you press DISC SKIP, the disc
tray turns so you can place the discs on
the empty compartments. The player
plays from the last disc placed on the
tray.
5
Press
H.
The disc tray closes, and the player starts
playback (continuous play). Adjust the
volume on the TV or the amplifier
(receiver).
playback (continuous play). Adjust the
volume on the TV or the amplifier
(receiver).
After following Step 5
Depending on the disc, a menu may appear
on the TV screen. You can play the disc
interactively by following the instructions on
the menu. DVD (page 36), VIDEO CD (page
37).
on the TV screen. You can play the disc
interactively by following the instructions on
the menu. DVD (page 36), VIDEO CD (page
37).
To turn on the player
Press POWER on the player. The player
enters standby mode and the power indicator
lights up in red. Press
enters standby mode and the power indicator
lights up in red. Press
?/1 on the remote. The
player turns on and the power indicator lights
up in green. In standby mode, the player also
turns on by pressing
up in green. In standby mode, the player also
turns on by pressing
A on the player or by
pressing
H.
1
4
7
2
5
8
0
3
6
9
POWER
A
H
Power indicator
x
AUDIO
x
?/1
DISC SKIP
H
DISC SKIP
With the playback
side facing down
Disc
compartment
number
33
P
lay
ing Disc
ing Disc
s
To turn off the player
Press
?/1 on the remote. The player enters
standby mode and the power indicator lights
up in red. To turn off the player completely,
press POWER on the player. While playing a
disc, do not turn off the player by pressing
POWER. Doing so may cancel the menu
settings. When you turn off the player, first
press
up in red. To turn off the player completely,
press POWER on the player. While playing a
disc, do not turn off the player by pressing
POWER. Doing so may cancel the menu
settings. When you turn off the player, first
press
x to stop playback and then press ?/1
on the remote.
Notes on playing DTS sound tracks on
a CD
• When playing DTS-encoded CDs,
excessive noise will be heard from the
analog stereo jacks. To avoid possible
damage to the audio system, the consumer
should take proper precautions when the
analog stereo jacks of the player are
connected to an amplification system. To
enjoy DTS Digital Surround™ playback, an
external 5.1-channel decoder system must
be connected to the digital jacks of the
player.
analog stereo jacks. To avoid possible
damage to the audio system, the consumer
should take proper precautions when the
analog stereo jacks of the player are
connected to an amplification system. To
enjoy DTS Digital Surround™ playback, an
external 5.1-channel decoder system must
be connected to the digital jacks of the
player.
• Set the sound to “STEREO” using the
AUDIO button when you play DTS sound
tracks on a CD (page 49).
tracks on a CD (page 49).
• Do not play DTS sound tracks without first
connecting the player to an audio
component having a built-in DTS decoder.
The player outputs the DTS signal via the
DIGITAL OUT (COAXIAL or OPTICAL)
jack even if “DTS” in “AUDIO SETUP” is
set to “OFF” in the Setup Display (page 68),
and may affect your ears or cause your
speakers to be damaged.
component having a built-in DTS decoder.
The player outputs the DTS signal via the
DIGITAL OUT (COAXIAL or OPTICAL)
jack even if “DTS” in “AUDIO SETUP” is
set to “OFF” in the Setup Display (page 68),
and may affect your ears or cause your
speakers to be damaged.
Notes on playing DVDs with a DTS
sound track
• DTS audio signals are output only through
the DIGITAL OUT (COAXIAL or
OPTICAL) jack.
OPTICAL) jack.
• If you connect the player to audio
equipment without a DTS decoder, do not
set “DTS” to “ON” in “AUDIO SETUP”
(page 68). A loud noise may come out from
the speakers, affecting your ears or causing
the speakers to be damaged.
set “DTS” to “ON” in “AUDIO SETUP”
(page 68). A loud noise may come out from
the speakers, affecting your ears or causing
the speakers to be damaged.
• When you play a DVD with DTS sound
tracks, set “DTS” to “ON” in “AUDIO
SETUP” (page 68).
SETUP” (page 68).
34
z
The Instant Replay function is useful when you
want to review a scene or dialog that you missed.
z
Before loading the discs, a DISC SELECT
indicator of an empty compartment may be lit.
• You may not be able to use the Instant Replay
function with some scenes.
• If you turn the power off by pressing POWER on the
player, the loading information will be reset.
You can open the disc tray while playing a
disc so that you can check which discs are to
be played next and replace discs without
interrupting playback of the current disc.
disc so that you can check which discs are to
be played next and replace discs without
interrupting playback of the current disc.
1
Press EXCHANGE.
The disc tray opens and two disc
compartments appear. Even if the player
is playing a disc, it doesn’t stop playing.
The disc tray opens and two disc
compartments appear. Even if the player
is playing a disc, it doesn’t stop playing.
2
Replace the discs in the compartments
with new ones.
with new ones.
3
Press DISC SKIP.
The disc tray turns and another two disc
compartments appear.
The disc tray turns and another two disc
compartments appear.
Additional operations
To
Operation
Select a disc
Press DISC SELECT 1
- 5 on the player
- 5 on the player
Stop
Press
x
Pause
Press
X
Resume play after
pause
pause
Press
X or H
Go to the next disc
Press DISC SKIP
Go to the next chapter,
track, or scene in
continuous play mode
track, or scene in
continuous play mode
Press
>
Go back to the
preceding chapter,
track, or scene in
continuous play mode
preceding chapter,
track, or scene in
continuous play mode
Press
.
Stop play and remove
the disc
the disc
Press
Z
Replay a previous
scene (DVD only)
scene (DVD only)
Press INSTANT
REPLAY
REPLAY
1
4
7
2
5
8
0
3
6
9
H
./>
Z
x
X
X
DISC SELECT 1 - 5
H
X
x
./>
INSTANT
REPLAY
REPLAY
DISC SKIP
LOAD
DISC SKIP
Check if a disc is in the
disc compartment
disc compartment
Press LOAD on the
player.
The DISC SELECT
indicator for each
compartment (1 - 5)
containing a disc lights
up.
player.
The DISC SELECT
indicator for each
compartment (1 - 5)
containing a disc lights
up.
Notes
Replacing discs while playing a disc
(EXCHANGE)
(EXCHANGE)
To
Operation
EXCHANGE
DISC SKIP
1-8
35
P
lay
ing Disc
ing Disc
s
4
Replace the discs in the compartments
with new ones.
with new ones.
5
Press EXCHANGE.
The disc tray closes.
The disc tray closes.
z
While the disc tray is open,
– If the playback of the current disc ends, the player
stops playing. If the disc is played in ONE DISC
Repeat Play mode, the current disc starts playing
again.
Repeat Play mode, the current disc starts playing
again.
– In ALL DISCS Shuffle Play mode (page 41),
titles/tracks/chapters are reshuffled only on the
current disc.
current disc.
– In Program Play mode (page 39), the titles/tracks/
chapters only on the current disc are played.
Do not push the disc tray to close in Step 5, as you may
damage the player.
damage the player.
Resuming Playback from
the Point Where You
Stopped the Disc
the Point Where You
Stopped the Disc
(Resume
Play)
When you stop the disc, the player
remembers the point where you pressed
remembers the point where you pressed
x
and “RESUME” appears on the front panel
display. As long as you do not open the disc
tray, Resume Play works even if the player
enters standby mode by pressing
display. As long as you do not open the disc
tray, Resume Play works even if the player
enters standby mode by pressing
?/1 on the
remote.
1
While playing a disc, press
x to
stop playback.
“RESUME” appears on the front panel
display and you can restart the disc from
the point where you stopped the disc.
If “RESUME” does not appear, Resume
Play is not available.
display and you can restart the disc from
the point where you stopped the disc.
If “RESUME” does not appear, Resume
Play is not available.
2
Press
H.
The player starts playback from the point
where you stopped the disc in Step 1.
where you stopped the disc in Step 1.
z
To play from the beginning of the disc, press
x
twice, then press
H.
Note
1
4
7
2
5
8
0
3
6
9
x
H
36
• Depending on where you stopped the disc, the player
may not resume playback from exactly the same
point.
point.
• The point where you stopped playing is cleared
when:
– you turn the power off by pressing POWER on the
– you turn the power off by pressing POWER on the
player.
– you change the play mode.
– you change the settings on the Setup Display.
– you load disc information by pressing LOAD on
– you change the settings on the Setup Display.
– you load disc information by pressing LOAD on
the player.
Using the DVD’s Menu
Some discs have a “title menu” or a “DVD
menu.” On some DVDs, this may simply be
called a “menu” or “title.”
menu.” On some DVDs, this may simply be
called a “menu” or “title.”
A DVD is divided into long sections of a
picture or a music feature called “titles.”
When you play a DVD which contains
several titles, you can select the title you want
using the title menu.
picture or a music feature called “titles.”
When you play a DVD which contains
several titles, you can select the title you want
using the title menu.
1
Press TITLE.
The title menu appears on the TV screen.
The contents of the menu vary from disc
to disc.
The title menu appears on the TV screen.
The contents of the menu vary from disc
to disc.
2
Press
C/X/x/c or the number buttons
to select the title you want to play.
3
Press ENTER.
The player starts playing the selected
title.
The player starts playing the selected
title.
z
You can also display the title menu by pressing
TITLE on the player.
Notes
Using the title menu
1
4
7
2
5
8
0
3
6
9
TITLE
C/X/x/c
ENTER
Number
buttons
buttons
ENTER
37
P
lay
ing Disc
ing Disc
s
Some DVDs allow you to select the disc
contents using a menu. When you play these
DVDs, you can select items such as the
language for the subtitles and the language
for the sound using the DVD menu.
contents using a menu. When you play these
DVDs, you can select items such as the
language for the subtitles and the language
for the sound using the DVD menu.
1
Press DVD MENU.
The DVD menu appears on the TV
screen. The contents of the menu vary
from disc to disc.
The DVD menu appears on the TV
screen. The contents of the menu vary
from disc to disc.
2
Press
C/X/x/c or the number buttons
to select the item you want to change.
3
To change other items, repeat Step 2.
4
Press ENTER.
z
You can also display the DVD menu by pressing
DVD MENU on the player.
Playing VIDEO CDs with
PBC Functions
PBC Functions
(PBC Playback)
With PBC (Playback Control) functions, you
can enjoy simple interactive operations,
search functions, and other operations.
PBC playback allows you to play VIDEO
CDs interactively by following the menu on
the TV screen.
can enjoy simple interactive operations,
search functions, and other operations.
PBC playback allows you to play VIDEO
CDs interactively by following the menu on
the TV screen.
1
Start playing a VIDEO CD with PBC
functions.
functions.
The menu for your selection appears.
2
Select the item number you want by
pressing
pressing
X/x or the number
buttons.
3
Press ENTER.
4
Follow the instructions in the menu
for interactive operations.
for interactive operations.
Refer to the instructions supplied with
the disc, as the operating procedure may
differ according to the VIDEO CD.
the disc, as the operating procedure may
differ according to the VIDEO CD.
To go back to the menu
Press
O RETURN.
Using the DVD menu
1
4
7
2
5
8
0
3
6
9
DVD MENU
C/X/x/c
ENTER
Number
buttons
buttons
ENTER
1
4
7
2
5
8
0
3
6
9
./>
H
O
RETURN
X/x
x
ENTER
ENTER
Number
buttons
buttons
38
z
To play without using PBC, press
./> or
the number buttons while the player is stopped to
select a track, then press
select a track, then press
H or ENTER.
“Play without PBC.” appears on the TV screen and the
player starts continuous play. You cannot play still
pictures such as a menu.
To return to PBC playback, press
player starts continuous play. You cannot play still
pictures such as a menu.
To return to PBC playback, press
x twice then press
H.
Depending on the VIDEO CD, “Press ENTER” in
Step 3 may appear as “Press SELECT” in the
instructions supplied with the disc. In this case, press
H.
Step 3 may appear as “Press SELECT” in the
instructions supplied with the disc. In this case, press
H.
Various Play Mode
Functions
Functions
(Program Play, Shuffle
Play, Repeat Play, A-B Repeat Play)
You can set the following play modes:
• Program Play (page 38)
• Shuffle Play (page 41)
• Repeat Play (page 42)
• A-B Repeat Play (page 43)
• Program Play (page 38)
• Shuffle Play (page 41)
• Repeat Play (page 42)
• A-B Repeat Play (page 43)
• The play mode is canceled when:
– you open the disc tray.
– the player enters standby mode by pressing
– the player enters standby mode by pressing
?/1
on the remote.
– you turn the power off by pressing POWER on the
player.
• If you are playing a VIDEO CD with PBC, you must
first cancel PBC playback before you can set a play
mode (except when you want to set A-B Repeat Play
for moving pictures).
mode (except when you want to set A-B Repeat Play
for moving pictures).
You can play one disc or all of the discs in the
player. Before setting Program Play, Shuffle
Play, or Repeat Play, you must select whether
to set those play mode on one disc or all of the
discs.
player. Before setting Program Play, Shuffle
Play, or Repeat Play, you must select whether
to set those play mode on one disc or all of the
discs.
Press ONE/ALL DISCS on the remote, or
ONE/ALL on the player to select
ONE/ALL on the player to select
(ONE
DISC mode) or
(ALL DISCS mode).
Note
Notes
Selecting the disc mode (One Disc or
All Discs)
All Discs)
0
ONE/ALL
DISCS
DISCS
Click on the first or last page to see other DVP-NC600 service manuals if exist.