DOWNLOAD Sony SLT-A37 / SLT-A37K / SLT-A37M / SLT-A37Y Service Manual ↓ Size: 6.07 MB | Pages: 30 in PDF or view online for FREE

SLT-A37/A37K/A37M/A37Y_L2

1-2

3)  Search the model whose new Destination Data file you want to get on the TISS homepage.
 

When the Destination Data file has been updated, a file with a name “Destination File For ‘model name’.zip” is registered.

(Example) Destination File For DSC-WX50.zip

Furthermore, the version supported by the Destination Data file is shown in the Remarks column.

Note : If the Destination Data file has not been updated, contact the Service Headquarters.

 4)  Download the Destination Data file of the relevant model and unzip the file.

5)  Execute “DESTINATION DATA WRITE” in the Adjust tab of the Adjust manual.
 

Click the [START] button.

6)  Click the [File Update] button in the window.
 

7)  A file selection screen opens. Select the Destination Data file to be added and click the [Open] button.
 

8)  When the file has been successfully added, the following window opens.
 

9)  Check the Destination Ver. window and confirm that the version has been updated.

Destination Ver. window

SLT-A37/A37K/A37M/A37Y_L2

1-3

Make sure to confirm below before replacing the AS Slider B Assy or the AS Holder Actuator Assy.

(1)  Remove the CV Rear Cover Assy (871), and temporally mount the AS Slider Unit (863).
(2)  Set the AS Slider Unit (863) upwards as shown in figure, and put it on a stable place.

 

(3)  Select “Slider Unit Check” of the adjustment software, and then confirm the movement to the directions of Pitch and Yaw, and if an error occurs,
 

replace it with the component part corresponding to the movement.

 

Note: The actual image may differ from the image shown above.

Make sure to confirm below after replacing the AS Slider B Assy or the AS Holder Actuator Assy.

(1)  Remove the CV Rear Cover Assy (871), temporally mount the AS Slider Unit (863) mounted with the Imager Sensor, and then set up the camera
 

body and hold the AS Slider Unit (863) as shown in figure.

 

(2)  Select “Slider Unit Check” of the adjustment software, and then confirm if the result is OK.
(3)  Select “Tebure Revise Adj.” of the adjustment software, and then confirm if the result is OK.
(4)  Mount the AS Slider Unit (863) to the camera.

 

Note: The actual image may differ from the image shown above.

SLT-A37/A37K/A37M/A37Y_L2

1-4

Removal Procedure
(1)  Remove the spring.

 

Spring

(2)  Remove the solder on the enamel wires at two places.

 

Solder

Solder

(3)  Remove the flexible board from the AS Slider B Assy.

 

Flexible Board

(4)  Remove the two screws.

 

(5)  Remove the AS Unit Holder Ball.

 

AS Unit Holder Ball

(6)  Remove the two Bearing Balls.

 

Bearing Ball

Bearing Ball

(7)  Remove the Cap SPs (for Pitch and Yaw).

 

Cap SP

(8)  Remove the Caps (for Pitch and Yaw).

 

Cap

(9)  Remove the AS Slider A Assy.
 

It can be done easily if A is removed beforehand.

 

AS Slider A Assy

A

(10)  Remove the AS Slider B Assy.
 

It can be done easily if B is removed beforehand.

 

AS Slider B Assy

B

(11)  Remove the three Bearing Balls.

 

Bearing Ball

Assembly Procedure

Note: Make sure to perform the assembly procedures after assembling the AS Holder Actuator Assy.

The assembly procedure is the reverse of the removal procedure.
Apply grease to the portions indicated below.

 

* After applying grease, attach the Bearing Balls.

 

Bearing Ball

G

G-15

 

AS Slider B Assy

G

G-15 and G G-116

 

* After applying grease, attach the Bearing Balls.

 

Bearing Ball

G

G-15

Bearing Ball

G

G-15

SLT-A37/A37K/A37M/A37Y_L2

1-5

Removal Procedure

Note: Make sure to perform the removal procedures after removing the
 

 AS Slider B Assy.

(1)  Remove the solder on the enamel wires at two places.

 

Solder

(2)  Remove the flexible board from the hook on the AS Holder Actuator
 Assy.

 

Hook

(3)  Remove the four screws to remove the AS Holder Actuator Assy.

 

AS Holder Actuator Assy

Assembly Procedure

Note: Make sure to perform the assembly procedures before assembling
 

 the AS Slider B Assy.

The assembly procedure is the reverse of the removal procedure.
Apply grease to the portions indicated below.

 

AS Holder Actuator Assy

G

G-15 and G G-116

1-2.  AM-030基板交換時の注意

仕向けデータ

補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と異なっている場合があります。

USBシリアルNo.

セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。

1-1.  P.O.I.の交換方法

取り外し方
(1)  MBミラー枠ホルダ係止SPを押し，P.O.I.をアップしてくだ
 

さい。

 

MBミラー枠ホルダ係止SP

(2)  P.O.I.を奥へ押しながらツメ2箇所を取り外してください。

 

ツメ

ツメ

P.O.I.

組み付け方
(1)  P.O.I.を組み付ける際，下図のようにP.O.I.へこみ部が手前，
 

下向きとなるように取り付けてください。

 

ツメ

ツメ

P.O.I.

へこみ部