DOWNLOAD Sony SLT-A37 / SLT-A37K / SLT-A37M / SLT-A37Y Service Manual ↓ Size: 6.07 MB | Pages: 30 in PDF or view online for FREE

SLT-A37/A37K/A37M/A37Y_L2

3-3

8.  MB Lens Lock Button, MB Lens Lock Pin, MB Lens Lock SP

MB Lens Lock Pin

MB Lens Lock Button

MB Lens Lock SP

9.  MB Ring SP, MB Mount Spacer, H Mount

G

G-85

H Mount

MB Mount Spacer

MB Ring SP

1

6

4

3

5

2

5.5

2.0

#163:

M2.0 X 5.5 (Tapping)
(Silver)
2-695-575-11

*

Tighten the six screws in order of the number.

Assembly-8: Assemble CV Front Cover Assy

When assembling the CV Front Cover Assy, check if
the focus mode switch of both CV Front Cover Assy and
MB AF/MF Change Lever are in AF position.

CV Front Cover Assy

MB AF/MF Change Lever

Focus Mode Switch

SLT-A37/A37K/A37M/A37Y_L2

3-4E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohol.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Press the Mirror Lock Lever to raise the P.O.I.
3.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

4.  Repeat “3” several times to clean up.
5.  According to service manual, check if there is dirt on the CCD.

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

1

Souse the cleaning
cloth in ethyl alcohol.

2

The dry cleaning cloth.

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310

OLPF

Mirror Lock Lever

SLT-A37/A37K/A37M/A37Y_L2

3-4E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohol.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Press the Mirror Lock Lever to raise the P.O.I.
3.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

4.  Repeat “3” several times to clean up.
5.  According to service manual, check if there is dirt on the CCD.

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

1

Souse the cleaning
cloth in ethyl alcohol.

2

The dry cleaning cloth.

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310

OLPF

Mirror Lock Lever

SLT-A37/A37K/A37M/A37Y_L2

3-4E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohol.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Press the Mirror Lock Lever to raise the P.O.I.
3.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

4.  Repeat “3” several times to clean up.
5.  According to service manual, check if there is dirt on the CCD.

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

1

Souse the cleaning
cloth in ethyl alcohol.

2

The dry cleaning cloth.

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310

OLPF

Mirror Lock Lever