Sony SLT-A33 / SLT-A33L / SLT-A33Y / SLT-A55 / SLT-A55L / SLT-A55V / SLT-A55VL / SLT-A55VY Service Manual ▷ View online
SLT-A33/A33L/A33Y/A55/A55V/A55L/A55VL/A55VY_L2
1-1
1. SERVICE NOTE
1-2. PRECAUTION ON REPLACING THE AM-022 BOARD
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
USB Serial No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
– ENGLISH –
1-1. METHOD FOR REPLACING THE P.O.I.
Method of Removal
(1) Press the MB Mirror Frame Holder Lock SP to raise the P.O.I.
MB Mirror Frame Holder Lock SP
(2) Unjoint the two claws while pressing the P.O.I. backward.
Claw
Claw
P.O.I.
1-3. METHOD FOR CHECKING THE AS SLIDER UNIT (863)
Make sure to confirm below before replacing the AS Slider B Assy or the AS Holder Actuator Assy.
(1) Remove the CV Rear Cover Assy (863), and temporally mount the AS Slider Unit (863).
(2) Set the AS Slider Unit (863) upwards as shown in figure, and put it on a stable place.
(3) Select “Slider Unit Check” of the adjustment software, and then confirm the movement to the directions of Pitch and Yaw, and if an error occurs,
replace it with the component part corresponding to the movement.
Method of Attachment
(1) When attaching the P.O.I., make the concave side of it face the
front and attach it downward.
Claw
Claw
P.O.I.
Concave side
SLT-A33/A33L/A33Y/A55/A55V/A55L/A55VL/A55VY_L2
1-2
– ENGLISH –
1-4. METHOD FOR ADJUSTING THE TEBURE REVISE
Make sure to confirm below after replacing the AS Slider B Assy or the AS Holder Actuator Assy.
(1) Remove the CV Rear Cover Assy (863), temporally mount the AS Slider Unit (863) mounted with the Imager Sensor, and then set up the camera
body and hold the AS Slider Unit (863) as shown in figure.
(2) Select “Slider Unit Check” of the adjustment software, and then confirm if the result is OK.
(3) Select “Tebure Revise Adj.” of the adjustment software, and then confirm if the result is OK.
(4) Mount the AS Slider Unit (863) to the camera.
1-5. METHOD FOR REPLACING THE AS SLIDER B ASSY
Removal Procedure
(1) Remove the spring.
Spring
(2) Remove the solder on the enamel wires at two places.
Solder
Solder
(3) Remove the flexible board from the AS Slider B Assy.
Flexible Board
(4) Remove the two screws.
(5) Remove the AS Unit Holder Ball.
AS Unit Holder Ball
(6) Remove the two Ball Bearings.
Ball Bearing
Ball Bearing
(7) Remove the Cap SPs (for Pitch and Yaw).
Cap SP
(8) Remove the Caps (for Pitch and Yaw).
Cap
(9) Remove the AS Slider A Assy.
It can be done easily if A is removed beforehand.
AS Slider A Assy
A
(10) Remove the AS Slider B Assy.
It can be done easily if B is removed beforehand.
AS Slider B Assy
B
(11) Remove the three Ball Bearings.
Ball Bearing
SLT-A33/A33L/A33Y/A55/A55V/A55L/A55VL/A55VY_L2
1-3
– ENGLISH –
1-7. GPS RECEIVING CHECK (SLT-A55V/A55VL/A55VY)
After a part of set was replaced or after the set was assembled, check the reception of GPS signal.
1-6. METHOD FOR REPLACING THE AS HOLDER ACTUATOR ASSY
Assembly Procedure
Note: Make sure to perform the assembly procedures after assembling the AS Holder Actuator Assy.
The assembly procedure is the reverse of the removal procedure.
Apply grease to the portions indicated below.
* After applying grease, attach the Ball Bearings.
Ball Bearing
G
G-15
AS Slider B Assy
G
G-15 and G G-116
* After applying grease, attach the Ball Bearings.
Ball Bearing
G
G-15
Ball Bearing
G
G-15
Removal Procedure
Note: Make sure to perform the removal procedures after removing the
AS Slider B Assy.
(1) Remove the solder on the enamel wires at two places.
Solder
(2) Remove the flexible board from the hook on the AS Holder Actuator
Assy.
Hook
(3) Remove the four screws to remove the AS Holder Actuator Assy.
AS Holder Actuator Assy
Assembly Procedure
Note: Make sure to perform the assembly procedures before assembling
the AS Slider B Assy.
The assembly procedure is the reverse of the removal procedure.
Apply grease to the portions indicated below.
AS Holder Actuator Assy
G
G-15 and G G-116
SLT-A33/A33L/A33Y/A55/A55V/A55L/A55VL/A55VY_L2
1-4
– JAPANESE –
1-3. ASスライダーユニット（863）チェック方法
ASスライダー B Assy又はASアクチュエータホルダAssyを交換する前に，必ず以下の確認を行ってください。
(1) CVリアカバー Assy（863）を取り外し，ASスライダーユニット（863）を仮付けします。
(2) ASスライダーユニット（863）を写真のように上向きにセットし，ボディを安定した場所に置きます。
(3) 調整ソフトのSlider Unit Checkを行い，PITCH，YAW方向の動きを確認し，エラーが出た場合，PITCH，YAWの
動きに対応した部品に交換します。
1-2. AM-022基板交換時の注意
仕向けデータ
補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と異なっている場合があります。
USBシリアルNo.
セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
1-1. P.O.I.の交換方法
取り外し方
(1) MBミラー枠ホルダ係止SPを押し，P.O.I.をアップしてくだ
さい。
MBミラー枠ホルダ係止SP
(2) P.O.I.を奥へ押しながらツメ2箇所を取り外してください。
ツメ
ツメ
P.O.I.
組み付け方
(1) P.O.I.を組み付ける際，下図のようにP.O.I.へこみ部が手前，
下向きとなるように取り付けてください。
ツメ
ツメ
P.O.I.
へこみ部
Click on the first or last page to see other SLT-A33 / SLT-A33L / SLT-A33Y / SLT-A55 / SLT-A55L / SLT-A55V / SLT-A55VL / SLT-A55VY service manuals if exist.