Sony SLT-A33 / SLT-A33L / SLT-A33Y / SLT-A55 / SLT-A55L / SLT-A55V / SLT-A55VL / SLT-A55VY Service Manual ▷ View online
SLT-A33/A33L/A33Y/A55/A55V/A55L/A55VL/A55VY_L2
3-4
Assembly-9: Note on attachment of EM GF Tape (A)
and IM Sheet Graphite
Note: When attaching the EM GF Tape (A) and the IM Sheet Graphite,
do not bend the AM-022 Board.
9-1. Attach the EM GF Tape (A) by aligning with the printing of
the AM-022 Board.
9-2. Peel off the released paper from the EM GF Tape (A), and then
attach the IM Sheet Graphite.
EM GF Tape (A)
AM-022 Board
IM Sheet Graphite
1-8. MB Lens Lock Button, MB Lens Lock Pin, MB Lens Lock SP
MB Lens Lock Pin
MB Lens Lock Button
MB Lens Lock SP
G
G-85
H Mount
MB Mount Spacer
MB Ring SP
1-9. MB Ring SP, MB Mount Spacer, H Mount
1
6
4
3
5
2
5.5
2.0
#163: M2.0 X 5.5 (Tapping)
(Silver)
2-695-575-11
∗ Tighten the six screws in order of the number.
Assembly-10: Assemble CV Front Cover Assy
When assembling the CV Front Cover Assy, check if
the focus mode switch of both CV Front Cover Assy and
MB AF/MF Change Lever are in AF position.
CV Front Cover Assy
MB AF/MF Change Lever
Focus Mode Switch
SLT-A33/A33L/A33Y/A55/A55V/A55L/A55VL/A55VY_L2
3-5E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1 Souse the one cleaning cloth in ethyl alcohol.
2 Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
* Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
* Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Press the Mirror Lock Lever to raise the P.O.I.
3. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
* Do not slide from right to left or up and down while dabbing.
4. Repeat “3” several times to clean up.
5. According to service manual, check if there is dirt on the CCD.
CCD Cleaning Jig (New)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
1
Souse the cleaning
cloth in ethyl alcohol.
2
The dry cleaning cloth.
Cleaning Jig
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
Cut
EE3310
OLPF
Mirror Lock Lever
SLT-A33/A33L/A33Y/A55/A55V/A55L/A55VL/A55VY_L2
3-5E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1 Souse the one cleaning cloth in ethyl alcohol.
2 Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
* Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
* Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Press the Mirror Lock Lever to raise the P.O.I.
3. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
* Do not slide from right to left or up and down while dabbing.
4. Repeat “3” several times to clean up.
5. According to service manual, check if there is dirt on the CCD.
CCD Cleaning Jig (New)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
1
Souse the cleaning
cloth in ethyl alcohol.
2
The dry cleaning cloth.
Cleaning Jig
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
Cut
EE3310
OLPF
Mirror Lock Lever
SLT-A33/A33L/A33Y/A55/A55V/A55L/A55VL/A55VY_L2
3-5E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1 Souse the one cleaning cloth in ethyl alcohol.
2 Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
* Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
* Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Press the Mirror Lock Lever to raise the P.O.I.
3. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
* Do not slide from right to left or up and down while dabbing.
4. Repeat “3” several times to clean up.
5. According to service manual, check if there is dirt on the CCD.
CCD Cleaning Jig (New)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
1
Souse the cleaning
cloth in ethyl alcohol.
2
The dry cleaning cloth.
Cleaning Jig
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
Cut
EE3310
OLPF
Mirror Lock Lever
