Sony SAL50F18 Service Manual ▷ View online
2-1
SAL50F18 (DT 1.8/50 SAM) (DT 50mm F1.8 SAM)
2. DISASSEMBLY
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
Notches
Holes
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Fixed screw
Fixed screw
Chip
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
Holes
NCPOP2B
SERVICE TOOLS
Grease (G-116):
J-6082-628-A
Grease (G-62):
J-6082-670-A
Grease (G-36):
J-6082-667-A
G-116
G-62
G-36
Grease (G-22):
J-6082-665-A
G-22
B-10
Adhesive bond (B-10):
J-6082-612-A
Grease (NCPOP2B): 7-640-016-79
Ver. 1.3 2011.09
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
SAL50F18 (DT 1.8/50 SAM) (DT 50mm F1.8 SAM)
2-2
2-1. DISASSEMBLY
REPAIR PARTS LIST
REPAIR PARTS LIST
HELP11
HELP03
HELP02
HELP04
HELP05
HELP12
HELP13
HELP09
HELP09
HELP08
HELP01
HELP10
HELP07
HELP06
1
3
4
5
2
4
3
B-10
B-10
B-10
2
qd
6
1
5
7
6
7
8
9
qa
q;
qs
G-22
G-36
G-36
G-116
G-36
G-116
PROJECTIVE RESOLVING
POWER ADJUSTMENT
POWER ADJUSTMENT
NCPOP2B
2-1-1
2-1-2
Switch Panel Block
(
Note 2
)
Note 1
Note 1:
How to remove the mount assembly
1. Remove four screws.
2. Set the focus to the infinity end.
3. Float the mount.
4. Disconnect the connector of PC board joint flexible.
5. Set the aperture of preset lever to “Open” and
How to remove the mount assembly
1. Remove four screws.
2. Set the focus to the infinity end.
3. Float the mount.
4. Disconnect the connector of PC board joint flexible.
5. Set the aperture of preset lever to “Open” and
disconnect the linkage of function lever and
driving wheel pin.
(Refer to HELP01.)
driving wheel pin.
(Refer to HELP01.)
Note 2:
How to remove the switch panel block (Scar prevention)
Insert tweezers or a narrow tip stick in the hole of rear mirror
assy tube and peel the switch panel block by pushing it
from the inside with the tweezers or a narrow tip stick.
(Refer to HELP03.)
How to remove the switch panel block (Scar prevention)
Insert tweezers or a narrow tip stick in the hole of rear mirror
assy tube and peel the switch panel block by pushing it
from the inside with the tweezers or a narrow tip stick.
(Refer to HELP03.)
Chip (Mount Index)
Function
Lever
Lever
Mount Cover
Main PC Board Assy
Main Spring
Mount
DC Motor (Geared)
Double-Coated
Adhesive Tape
Adhesive Tape
Decoration Seal
Rear Mirror Assy Tube
Reinforcement
Brush
Brush
Interception
Interception Tape
Focos Rubber
Focos Brush
Bolt Screw
Outer Tube Assy
Front Group Assy
Filter Screw Frame
Helicoid Male
Rear Group Assy
Stopper
Screw
Screw
Midway Mirror Tube
Focus Ring Assy
Vertical Groove
Cylinder
Cylinder
PC Board Joint Flexible
LOCTITE 460
or the equivalent
or the equivalent
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
APERTURE DIAMETER
ADJUSTMENT
ADJUSTMENT
FOCUS BRUSH POSITION
ADJUSTMENT
ADJUSTMENT
Ver. 1.3 2011.09
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
HELP
SAL50F18 (DT 1.8/50 SAM) (DT 50mm F1.8 SAM)
HELP
Note for assembling and grease applying positions are shown.
HELP01
How to remove the mount assy
1.
Remove four screws.
2.
Set the focus to the infinity end.
3.
Float the mount.
4.
Disconnect the connector of PC board joint flexible.
5.
Set the aperture of preset lever to “Open” and disconnect the linkage of function lever and driving wheel pin.
Mount Assy
PC Board Joint Flexible
Function Lever
Preset Lever
Driving Wheel Pin
HELP
SAL50F18 (DT 1.8/50 SAM) (DT 50mm F1.8 SAM)
How to install the mount assy
1.
Set the focus to the infinity end.
2.
Set the aperture positions of driving wheel pin and preset lever “Open”.
3.
Link the function lever with the driving wheel pin.
4.
Connect the PC board joint flexible.
5.
Fix the mount assy with four screws.
Mount Assy
Preset Lever
Function Lever
PC Board Joint Flexible
Driving
Wheel Pin
Wheel Pin
Click on the first or last page to see other SAL50F18 service manuals if exist.