Sony SAL35F14G Service Manual ▷ View online
HELP
SAL35F14G (1.4/35G) (35mm F1.4G)
HELP03
Adhesive bond (B-40): J-6082-614-A
1.
Align the ring positioning pin of the mirror barrel tube block to U groove of the fixed barrel, attach them.
2.
Apply the adhesive bond (B-40) to 3 screws shown in figure and tighten the screws.
Mirror Barrel Tube Block
Ring Positioning Pin
1 Group Lens Block
U Groove
Apply the adhesive bond (B-40)
Apply the adhesive bond (B-40)
HELP
SAL35F14G (1.4/35G) (35mm F1.4G)
HELP04
Adhesive bond (B-40): J-6082-614-A
Apply the adhesive bond (B-40) to 5 screws shown in figure and tighten the screws.
HELP05
Adhesive bond (LOCTITE 460) (Note)
Note:
Use adhesive bond (LOCTITE 460) or an equivalent article.
Do not use what becomes white after drying like quick-drying glue.
Anti-diffusion agent (A-20): J-6082-611-A
Grease (G-85):
J-6082-626-A
1.
Apply the anti-diffusion agent (A-20) to the indicated portions of lens A mount.
2.
Apply the grease (G-85) to 3 locations of indicated portion3 (3 locations) of lens A mount.
3.
Apply the adhesive bond (LOCTITE 460) to the stopper screw and attach it to the lens A mount.
Apply the adhesive bond (B-40)
Apply the adhesive bond (B-40)
Apply the adhesive bond (B-40)
Rear Light Shield Barrel
Lens A Mount
Apply the grease (G-85) to 3 locations of
indicated portion.
indicated portion.
Apply the anti-diffusion agent (A-20)
to all circumferences of indicated Portion.
to all circumferences of indicated Portion.
Apply the adhesive bond (LOCTITE 460)
Stopper Screw
Apply the grease (G-85) (rear side)
HELP
SAL35F14G (1.4/35G) (35mm F1.4G)
HELP06
Oil (O-20): J-6082-610-A
Apply small amount of oil (O-20) to the instruction portion of the main spring.
HELP07
Adhesive bond (B-40):
J-6082-614-A
Anti-diffusion agent (A-20): J-6082-611-A
1.
Apply the anti-diffusion agent (A-20) to the indicated portion of outer barrel and G decoration ring.
2.
Apply the adhesive bond (B-40) to 4 screws shown in figure and tighten the screws.
3.
Lay out the DV-FH Flexible properly.
Aplly small amount(O-20)(On contact area)
Connector
DV-FH flexible
DV-FH Flexible
Apply the adhesive bond (B-40)
Apply the adhesive bond (B-40)
Apply the anti-diffusion agent (A-20) to
all circumferences of indicated portions.
all circumferences of indicated portions.
Apply the anti-diffusion agent (A-20) (inside) to
all circumferences of indicated portions.
all circumferences of indicated portions.
Apply the anti-diffusion agent (A-20)
Mount Index
Outer Barrel and G Decoration Ring
Outer Barrel
G Decoration Ring
HELP
SAL35F14G (1.4/35G) (35mm F1.4G)
HELP08
1.
Attach the cam ring support plate to the fixed tube block, tighten the two screws.
2.
Affix the polyester tape (black) 10mm to the joint line of cam ring support plate.
3.
Affix the focus scale plate with polyester tape (black) 10mm, aligning with the punch mark on the fixed tube block.
4.
Affix of polyester tape (black) 10mm to the locations indicated in figure.
5.
Leave space 1mm between edge and adhesive sheet, affix the adhesive sheet to cam ring support plate.
Ver 1.2 2007.06
1mm
6mm
Cam Ring Support Plate
Adhesive Sheet
5 to10mm
(Width of overlapping)
Fixed Barrel Block
Adhesive Sheet
Cam Ring Support Plate
Focus Scale Plate
Fixed Barrel Block
Punch Mark
Cam Ring Support Plate
Polyester Tape (Black) 10mm
(10
(10
×
45mm)
Align with the punch mark on the
cam ring and fixed barrel.
cam ring and fixed barrel.
Sticking standard : Right edge of focus scale plate
Sticking it so that A and B may
almost become the same.
almost become the same.
Sticking standard : Center
A
B
Polyester Tape (Black) 10mm
(10
(10
×
25mm)
Polyester Tape (Black) 10mm
(10
(10
×
35mm)
Click on the first or last page to see other SAL35F14G service manuals if exist.