DOWNLOAD Sony SAL30M28 Service Manual ↓ Size: 7.77 MB | Pages: 48 in PDF or view online for FREE

SAL30M28 (DT 2.8/30 MACRO SAM) (DT 30mm F2.8 Macro SAM)

2-2

1

4

6

2

3

B-10

B-10

B-10

3

2

qs

7

1

5

8

6

7

8

q;

9

qa

G-22

NCPOP2B

G-116

G-36

G-36

G-36

G-116

G-36

LOCTITE 460
or the equivalent

G-116

Note 1:
How to remove the mount assy
1. Remove four screws.
2. Set the focus to the infinity end.
3. Float the mount.
4. Disconnect the connector of PC board joint flexible.
5. Set the aperture of preset lever to "Open" and 
    disconnect the linkage of function lever and 
    driving wheel pin.
   (Refer to HELP 01.)

Note2:
How to remove the switch panel block (Scar prevention)
Insert tweezers or a narrow tip stick in the hole of rear mirror 
assy tube and peel the switch panel block by pushing it from 
inside with the tweezers or the narrow tip stick.
(Refer to HELP 5.)

Interception

Rear Mirror Assy Tube

Decoration Seal

Main PC Board ASSY

G06 Frame Assy

Adjustment Washer

Main Spring

Preset Ring

Function Lever

Mount

Mount Cover

Focus Rubber

Interception Tape

Focus Brush

Reinforcement
Brush

Vibration Proof
Sheet

Outer Barrel

Filter Screw Frame

Bolt Screw

Front Group 
(Rear) Group Assy

Helicoid Male

Vertical Groove
Cylinder

Focus Ring Assy

Middle Lens Barrel Assy

PC Board Joint Flexible

DC Motor (Geared)

Double-Coated 
Adhesive Tape

Chip (Mount Index)

2-1-1

2-1-2

Switch Panel Block

(

Note 2

)

Note 1

SAL30M28 (DT 2.8/30 MACRO SAM) (DT 30mm F2.8 Macro SAM)

2-3

Note for assembling and grease applying positions are shown.

SAL30M28 (DT 2.8/30 MACRO SAM) (DT 30mm F2.8 Macro SAM)

How to remove the mount assy

1.  Remove four screws.
2.  Set the focus to the infinity end. 
3.  Float the mount. 
4.  Disconnect the connector of PC board joint flexible.
5.  Set the aperture of preset lever to  Open  and disconnect the linkage of function lever and driving wheel pin.

PC Board Joint Flexible

Mount

Preset Lever

Function Lever

Driving Wheel Pin

How to install the mount assy

1.  Set the focus to the infinity end. 
2.  Set the aperture positions of driving wheel pin and preset lever  Open . 
3.  Link the function lever with the driving wheel pin. 
4.  Connect the PC board joint flexible. 
5.  Fix the mount assy with four screws.

PC Board Joint Flexible

Preset Lever

Function Lever

Driving 
Wheel Pin

Mount

How to remove the connection board

1.  Remove two stopper screws securing connection board. 
2.  Push down the inner side of connection board. 
3.  Remove the Main PC board assy with shifting the outside of connection board to inward.

2

3

Connection Board

Connection Board

Main PC Board Assy

1

Outside

Inside

Stopper Screws Securing
Connection Board

How to attach the connection board

1.  Push the outside of connection board to outward. 
2.  Install the Main PC board assy with pushing up the inside of connection board. 
3.  Tighten two stopper screws securing connection board.

1

2

3

Connection Board

Connection Board

Main PC Board Assy

Outside

Inside

Stopper Screws Securing
Connection Board

SAL30M28 (DT 2.8/30 MACRO SAM) (DT 30mm F2.8 Macro SAM)

2-4

Grease (G-36): J-6082-667-A

1.  Apply the grease (G-36) to the main spring sliding surface of mount.

  Do not spread the grease to the mount inner side.

  Do not apply the grease to the 1mm from edge of wall.

Mount

Do not spread the grease 
to the mount inner side

Cross section (Coating portion)

1mm
(Edge of wall)

Do not apply

Apply the grease (G-36)
(Main spring sliding surface)

Grease (G-36)

1.  Install the G06 frame assy, fix it with three screws.

  Install it so that round mark of G06 frame assy (object side) is located on the index side.

Round mark

Distance 
index

G06 Frame Assy

G06 Frame Assy (Object side)

How to remove the switch panel block (Scar prevention)

1.  Remove three screws fixing the rear mirror assy tube.
2.  Set the switch panel block to  AF .
3.  Hold down the middle lens barrel assy and pull up the rear mirror assy tube slightly to the direction of the mount until the in-

dicated hole of rear mirror assy tube is seen.

4.  Insert tweezers or a narrow tip stick in the hole of rear mirror assy tube and peel the switch panel block by pushing it from the 

inside with the tweezers or the narrow tip stick.

Rear Mirror Assy Tube

Direction of the Mount

Middle Lens Barrel Assy

Narrow tip stick

Hole

Switch Panel Block

Note on the switch panel block installation

1.  Set the select switch of DC motor (geared) to AF.
2.  Set the knob of switch panel block to AF.
3.  Peel the released paper off the switch panel block and install the switch panel block.

Select switch of
DC Motor (Geared)

Switch Panel Block

Knob

AF Side

MF Side

SAL30M28 (DT 2.8/30 MACRO SAM) (DT 30mm F2.8 Macro SAM)

2-5

1.  Install the rear mirror assy tube, aligning the installation hole of switch panel block with the select switch DC motor (geared).
2.  Fix it with three screws.

Installation hole of
Switch Panel Block

Rear Mirror Assy Tube

Select switch of
DC Motor (Geared)

1.  Affix the flexible of DC motor (geared) to the middle lens barrel assy.
2.  Connect the PC board joint flexible to the connector.

PC Board Joint Flexible

DC Motor (Geared)

Middle Lens Barrel Assy

Connector

1.  Fold the PC board joint flexible as shown in the illustration.
2.  Affix the PC board joint flexible along the reference.

PC Board Joint Flexible 

Reference for affixing

Crest folds

Valley folds

1.  Install the interception by inserting three pins of interception in the three holes of filter screw frame.

  Install it so that each cut portion of interception is located in SONY printing of the rear mirror assy tube.

Rear Mirror 
Assy Tube

SONY printing

Pins

Distance index

Holes

Main Unit Assy

Hole

Cut portion

Cut portion

Interception