Sony SAL18552 Service Manual ▷ View online
2-8
SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)
HELP14
Grease (FT-210): 9-913-200-37
1. Apply the grease (FT-210) to the indicated portion of zoom barrel assy.
Apply the grease
(FT-210)
(FT-210)
Be careful not to apply
the grease to this area.
the grease to this area.
Zoom Barrel Assy
HELP15
1. Align the cut portion of zoom barrel assy with the cut portions of zoom sheet.
2. Aligning the projections of front lens barrel with the cut portions of zoom barrel assy, insert the zoom barrel assy in the front lens
2. Aligning the projections of front lens barrel with the cut portions of zoom barrel assy, insert the zoom barrel assy in the front lens
barrel block.
Zoom Barrel Assy
Zoom Sheet
Front Lens Barrel Block
Front Lens Barrel
Projection
Projection
Projection
Cut Portions
HELP16
Grease (SG-310): 9-913-200-36
1. Apply the grease (SG-310) to the indicated portions of front lens barrel. (Three locations)
Note:
Apply the grease so that the groove of helicoid is filled with grease.
2. Apply the grease (SG-310) to the indicated portions of front lens barrel. (Three locations)
Front Lens Barrel
Apply the grease (SG-310)
Apply the grease (SG-310)
Apply the grease (SG-310)
(Fill the groove of helicoid with the grease)
(Fill the groove of helicoid with the grease)
Apply the grease (SG-310)
(Fill the groove of helicoid with the grease)
(Fill the groove of helicoid with the grease)
HELP17
1. Mount the GP1 moving barrel on the front lens barrel.
2. Rotate counterclockwise (viewing from the mount side) the GP1 moving barrel and assemble it by rotating it clockwise at the position
2. Rotate counterclockwise (viewing from the mount side) the GP1 moving barrel and assemble it by rotating it clockwise at the position
where the helicoid is engaged (clicked).
Note:
Note:
When moving the helicoid to the last, confirm that the bayonet click portion comes to the location where the screw hole
locates about 90 de-
grees apart from the pin of fixed sleeve in the clockwise direction (viewing from the mount side).
GP1 Moving Barrel
Front Lens
Barrel
Barrel
Fixed
Sleeve
Sleeve
Front Lens Barrel
GP1 Moving
Barrel
Barrel
Helicoid
Pin
Meet the helicoids each other by rotating
counterclockwise the GP1 Moving Barrel
counterclockwise the GP1 Moving Barrel
When the helicoid engages (clicks),
assemble the GP1 Moving Barrel
by rotating it clockwise.
assemble the GP1 Moving Barrel
by rotating it clockwise.
Screw hole at the location where it is
clockwise (viewing from the mount)
turned by about 90 degrees from the pin
clockwise (viewing from the mount)
turned by about 90 degrees from the pin
Bayonet click portion
2-9
SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)
HELP18
Grease (FT-210): 9-913-200-37
Grease (SG-310): 9-913-200-36
Grease (SG-310): 9-913-200-36
1. Apply the grease (SG-310) to the grooves of fixed sleeve. (Three locations)
Note:
Apply the grease so that the groove is filled with grease.
2. Apply the grease (FT-210) to the wall of oblong hole of fixed sleeve. (Six locations)
Fixed Sleeve
Apply the grease (SG-310)
to the grooves (Three locations)
(Groove is filled)
to the grooves (Three locations)
(Groove is filled)
Apply the grease (FT-210)
to the wall of oblong hole
(Six locations)
to the wall of oblong hole
(Six locations)
3. Apply the grease (SG-310) to the indicated portions of GP1 moving barrel. (Six locations)
Note:
Apply the grease so that the grease remains on the wall.
GP1 Moving Barrel
Apply the grease (SG-310)
(Six locations)
(Six locations)
4. Apply the grease (SG-310) to the helicoids of zoom cam sleeve. (Six locations)
Note:
Apply the grease so that the grease remains on the wall.
Apply the grease (SG-310)
(Three locations)
(Three locations)
Zoom Cam Sleeve
Apply the grease (SG-310)
(Three locations)
(Three locations)
HELP19
1. Align the cut portions A of fixed sleeve with the projections of GP1 moving barrel and drop the fixed sleeve in GP1 moving barrel.
2. While holding the fixed sleeve and the GP1 moving barrel, install the zoom cam sleeve, aligning the projections of zoom cam sleeve
2. While holding the fixed sleeve and the GP1 moving barrel, install the zoom cam sleeve, aligning the projections of zoom cam sleeve
with the cut portions B of fixed sleeve.
Fixed Sleeve
GP1 Moving Barrel
Zoom Cam Sleeve
Fixed Sleeve
GP1 Moving Barrel
Cut Portion A
Cut Portion B
Cut Portion B
Cut Portion B
Projection
Projection
3. Align the cut portions A of fixed sleeve with the projections of GP1 moving barrel again and assemble the zoom cam sleeve by rotating
it counterclockwise (viewing from the mount side).
Fixed Sleeve
Zoom Cam Sleeve
Fixed Sleeve
GP1 Moving
Barrel
Barrel
Cut Portion A
Projection
Rotate counterclockwise
the Zoom Cam Sleeve
(Viewing from the mount side)
the Zoom Cam Sleeve
(Viewing from the mount side)
2-10
SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)
HELP20
1. When affixing the ZF flexible PWB, align it with the affixing index as shown in the figure below.
ZF Flexible PWB
Fixed Hold Ring
Affixing index
HELP21
Grease (FT-210): 9-913-200-37
Grease (SG-310): 9-913-200-36
Grease (SG-310): 9-913-200-36
1. Apply the grease (SG-310) to the indicated portions of focus drive ring. (Seven locations)
Apply the grease (SG-310)
(Three locations)
(Three locations)
Focus Drive Ring
Focus Drive Ring
Apply the grease (SG-310)
(Four locations)
(Four locations)
2. Apply the grease (FT-210) to the inner grooves of focus drive ring. (Three locations)
Apply the grease (FT-210)
(Three locations)
(Three locations)
Focus Drive Ring
HELP22
1. Aligning the groove at the start of focus gear with the projection near the gear inserting portion of fixed hold ring, insert the focus drive
ring.
2. Rotate the focus drive ring so that the installing portion of focus stopper comes to the oblong hole of fixed hold ring.
Fixed Hold Ring
Focus Drive Ring
Focus Drive Ring
Fixed Hold Ring
Oblong Hole
Groove
Projection
Gear inserting portion
Start of Focus Gear
Installing portion of
Focus Stopper
Focus Stopper
3. Install the focus stopper and fix it with two screws.
Focus Stopper
SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)
2-11E
HELP23
How to remove the mount cover
1. Set claw A free from the groove on lens mount.
2. Remove claw B.
3. Set claw C free from the groove on lens mount.
2. Remove claw B.
3. Set claw C free from the groove on lens mount.
Claw A
Claw A
Groove on lens mount
Claw B
Claw C
Mount Cover
Mount Cover
How to attach the mount cover
1. Press claw C down into the groove on lens mount.
2. Put claw B on.
3. Press claw A down into the groove on lens mount.
2. Put claw B on.
3. Press claw A down into the groove on lens mount.
Claw A
Groove on lens mount
Claw A
Claw B
Claw C
Mount Cover
Mount Cover
Click on the first or last page to see other SAL18552 service manuals if exist.