DOWNLOAD Sony NEX-VG30 / NEX-VG30E / NEX-VG30EH / NEX-VG30EM / NEX-VG30H (serv.man2) Service Manual ↓ Size: 7.85 MB | Pages: 31 in PDF or view online for FREE

NEX-VG30/VG30E/VG30EH/VG30EM/VG30H_L2

3-1

Assembly-1: Installation Cautions of the Cabinet (R) 

Section.

FP-1438 Flexible Board

Route the FP-1438 Flexible Board as shown.

Assembly-2: The Method of attachment of the FP-1442 

Flexible Board

A

 Fold dotted line parts of the FP-1442 Flexible Board as 

shown in figure.

Mountain fold

Valley fold

FP-1442 
Flexible Board

Mountain
fold

Valley fold

Adhesive tape

Adhesive tape

Adhesive tape

Adhesive tape

Assembly-3: Installation Cautions of the Cabinet (L) 

Block Section.

Route the 

Battery Connector Harness 

as shown.

Hooks

Battery Connector
Harness 

Cabinet (L) Block Section

Route the 

Flexible Flat Cable (FFC-233) 

as shown.

Flexible Flat Cable
(FFC-233)

Hook
(Guard panel VC)

Route the 

Flexible Board of the PS36000 Control Switch Block 

 as shown.

Flexible Board of the
PS36000 Control Switch
Block

Hooks

Assembly-4: Installation Cautions of the Mount Block 

Section.

Route the 

FP-1449 Flexible Board

 as shown.

Slit

Guard panel

FP-1449 

Flexible Board

FP-2061 Flexible Board

Route the 

FP-2061 Flexible Board

 as shown.

B

 Insert the FP-1442 Flexible Board to the Flexible Clamp as 

shown in figure.

FP-1442 
Flexible Board

Flexible Clamp

C

 Insert the FP-1442 Flexible Board and the Flexible Clamp to 

the Pannel Hinge Assy.

Flexible Clamp

FP-1442 
Flexible Board

Panel Hinge
Assy

D

 Roll the FP-1442 Flexible Board 1 times and half in the Panel 

Hinge Assy as shown in figure.

 

And attach the FP-1442 Flexible Board to the Panel Hinge 
Assy.

Attach the FP-1442
Flexible Board.

Roll the FP-1442
Flexible Board.

FP-1442 
Flexible Board

Panel Hinge
Assy

NEX-VG30/VG30E/VG30EH/VG30EM/VG30H_L2

3-2

Assembly-5: Putting position of the IM Adjust Washer (A, 

B, C)

Mount Base

IM Adjust Washer B

IM Adjust Washer A

IM Adjust Washer C

1

2

3

Screw tightening sequence when
assembling the Imager Block.

Imager Block

Assembly-8: Apply grease on the MB N Plate SP

MB N Plate SP

G G-85

(J-6082-626-A)

Assembly-9: Installation Cautions of the Optical Filter 

Block.

The two-layer 

side is on the 

imager side.

Mount 
Side

Imager
Side

Optical Filter Block

Flare Cut IM Plate (754)

Glass Retainer IM Plate (754)

The two-layer side of the Optical filter block is on the
imager side.

Assembly-6: Method of attachment of the MB Mask 

Sheet

Note:  There should not be any misalignment when attaching 

the MB Mask Sheet.

J-6082-735-A

MB Mask Sheet

MB Mask 
Sheet Tape

Cabinet (F)

Assembly-7: Screw tightening sequence when assem-

bling the MB N Plate A (945).

MB N Plate A (945)

1

2

3

4

NEX-VG30/VG30E/VG30EH/VG30EM/VG30H_L2

3-3E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

<CAUTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohol.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

3.  Repeat “3” several times to clean up.
4.  According to the service manual, check if there is dirt on the OLPF.

1

Souse the cleaning
cloth in ethyl alcohol.

2

The dry cleaning cloth.

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310

OLPF

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

NEX-VG30/VG30E/VG30EH/VG30EM/VG30H_L2

3-3E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

<CAUTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohol.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

3.  Repeat “3” several times to clean up.
4.  According to the service manual, check if there is dirt on the OLPF.

1

Souse the cleaning
cloth in ethyl alcohol.

2

The dry cleaning cloth.

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310

OLPF

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet