Sony NEX-VG30 / NEX-VG30E / NEX-VG30EH / NEX-VG30EM / NEX-VG30H (serv.man2) Service Manual ▷ View online
NEX-VG30/VG30E/VG30EH/VG30EM/VG30H_L2
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original one.
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay
• -XX, -X mean standardized parts, so they may have some differences from the original one.
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay
should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Due to standardization, replacements in the parts list may be different from the parts specified
• Due to standardization, replacements in the parts list may be different from the parts specified
in the diagrams or the components used on the set.
• CAPACITORS:
uF:
uF:
μF
• COILS
uH:
uH:
μH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
nonflammable
• SEMICONDUCTORS
In each case, u: μ, for example:
uA...:
In each case, u: μ, for example:
uA...:
μA... , uPA... , μPA... ,
uPB...
,
μPB... , μPC... , μPC... ,
uPD...,
μPD...
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及び
セットに付いている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金 被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。
図面番号で部品を指定するときは基板名
又はブロックを併せて指定してください。
又はブロックを併せて指定してください。
お願い
• Color Indication of Appearance Parts
Example:
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
• 外装部品色表示
例：
(SILVER) ：セットの色を表す。
(Silver) ：部品の色を表す。
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
le numéro spécifié.
0印の部品，または0印付の点線で囲ま
れた部品は，安全性を維持するために，
重要な部品です。
従って交換時は，必ず指定の部品を使用
してください。
れた部品は，安全性を維持するために，
重要な部品です。
従って交換時は，必ず指定の部品を使用
してください。
When indicating parts by reference number,
please include the board name.
please include the board name.
• Abbreviation
CH
CH
: Chinese model
CND : Canadian model
J
J
: Japanese model
JE :
Tourist
model
View Position
Right View
Left View
Front View
Bottom View
Top View
Back View
ACCESSORIES
ASSEMBLY
5
EVF Section
9
Cabinet (R) Section
qs
Cabinet (L) Section
q;
MS-1002 Board
4
Mic Block Section
• MA-1002 Board
(MA-478 Board)
(MA-478 Board)
1
Handle (Upper) Section
6
Cabinet (G) Block
7
Cabinet (BM) Assy
8
Hinge Cabinet
3
GP-1010 Board
(GP-1002 Board)
qa
Handle Block Assy
qd
Mount Block Section
qf
Main Board Section
• DC-1002 Board
(DC-115 Board)
• VC-1011 Board
• FP-1431 Flexible Board
• FP-1432 Flexible Board
• FP-1438 Flexible Board
• FP-1440 Flexible Board
• FP-1450 Flexible Board
• FP-2037 Flexible Board
(DC-115 Board)
• VC-1011 Board
• FP-1431 Flexible Board
• FP-1432 Flexible Board
• FP-1438 Flexible Board
• FP-1440 Flexible Board
• FP-1450 Flexible Board
• FP-2037 Flexible Board
• IS-073 Board
• MT-1003 Board
• RT-1002 Board
• FP-1433 Flexible Board
• FP-1434 Flexible Board
• FP-1448 Flexible Board
• FP-1449 Flexible Board
• FP-1457 Flexible Board
• FP-2061 Flexible Board
• MT-1003 Board
• RT-1002 Board
• FP-1433 Flexible Board
• FP-1434 Flexible Board
• FP-1448 Flexible Board
• FP-1449 Flexible Board
• FP-1457 Flexible Board
• FP-2061 Flexible Board
• CK-238 Board
• PD-1014 Board
(PD-446 Board)
• FP-1442 Flexible Board
• PD-1014 Board
(PD-446 Board)
• FP-1442 Flexible Board
• HP-1003 Board
(HP-1002 Board)
• FP-1441 Flexible Board
(HP-1002 Board)
• FP-1441 Flexible Board
• VF-1002 Board
• FP-2005 Flexible Board
• FP-2038 Flexible Board
• FP-2005 Flexible Board
• FP-2038 Flexible Board
2
Shoe Connector Assy
• FP-2006 Flexible Board
NEX-VG30/VG30E/VG30EH/VG30EM/VG30H_L2
2-2
– ENGLISH –
– JAPANESE –
NOTE FOR REPAIR
修理時の注意
• Make sure that the flat cable and flexible board are not cracked or
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, do not pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, do not press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
• フラットケーブルおよびフレキシブル基板の端子面に欠け，折
れ等がないことを確認する。
また，コネクタへの接続は，差し込み不足や斜め差しにならな
いように注意する。
• コネクタを取り外す時に，線材部（極細）を持って引っ張ると断
線する恐れがありますので，絶対に線材部（極細）を持って引っ
張らないでください。
張らないでください。
• 線材部（極細）を押さえながらコネクタを差し込むと，線材部（極
細）が断線する恐れがありますので，絶対に線材部（極細）には負
担をかけないでください。
担をかけないでください。
• 金メッキされているフレキシブル基板には，強い負担をかけな
いでください。
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
NEX-VG30/VG30E/VG30EH/VG30EM/VG30H_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION-1
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
4-257-594-01
LOWER, MIC CABINET
2
4-299-857-01 GUARD,
MIC
3
A-1848-226-A MA-478 BOARD, COMPLETE (Note 2)
3
(Not supplied) MA-1002 BOARD, COMPLETE (Note 2)
4
1-839-024-11
CABLE, FLEXIBLE FLAT (FFC-266)
5
X-2582-834-1 CABINET
ASSY,
MIC
6
4-257-591-11 CABINET,
GUARD
7
4-257-593-01 CUSHION,
MIC
8
4-257-592-01
PLATE, GUARD FIXED
9
A-1902-804-A GP-1002 BOARD, COMPLETE (Note 3)
9
(Not supplied) GP-1010 BOARD, COMPLETE (Note 3)
10
4-437-498-01
SHEET METAL (456), (S) BELT
11
X-2585-389-1 FRAME (456) ASSY, SHOE
* 12
4-257-740-01 RETAINER, MIC
13
4-257-738-01
BRACKET, C SHOE
14
4-437-496-01
CABINET (456), HANDLE (UPPER)
15
3-067-469-11 SHOE,
ACCESSORY
16
4-437-497-01
COVER (456), SHOE
17
A-1902-807-A FP-2006 FLEXIBLE BOARD, COMPLETE
MIC901 1-542-831-11
MICROPHONE UNIT (MIC36000)
#2
2-635-562-31 SCREW
(M1.7)
#11
3-078-890-11 SCREW,
TAPPING
#69
2-599-475-21 SCREW
(M1.7)
#107
3-032-750-01
(+) K SCREW M2 (Note 1)
#281
3-053-446-01
SCREW (1.7X2), +P GRIP
DISASSEMBLY
1. Remove in numerical order (
1
to
5
) in the left figure.
1
Open the Shoe Cover (
1
-1
) → #107 X 2 →
Remove the Accessory Shoe (
1
-2
) → #2 X 1
3
#2 X 4 → Remove the C Shoe Bracket (
3
-1
) → #2 X 1 →
Remove the MIC Retainer (
3
-2
)
4
#2 X 1
5
Tilt the EVF (
5
) → #2 X 3
Top View
#107
#2
Top View
#2
Top View
Top View
#2
#2
#2
#2
Top View
Right View
#2
Back View
5
2
#2 X 4
Top View
#2
#2
Note
Note 1: This screw cannot be reused. Discard the screw removed
once in servicing.
Instead, use a new screw.
Note 1: このねじは再利用することができません。
サービス対応時に一度でも外した場合は新品のねじと交換
してください。
してください。
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
3-078-890-11
4.0
1.7
#69: M1.7 X 3.0
(Silver)
2-599-475-21
2-599-475-21
3.0
1.7
#281: M1.7 X 2.0
(Silver)
3-053-446-01
3-053-446-01
2.0
1.7
#107: M2.0 X 5.0
(Silver)
3-032-750-01
3-032-750-01
5.0
2.0
Note 2: Servicing board of the MA-1002 board is the MA-478 board.
They are equality boards.
Note 2: MA-1002基板のサービス用基板はMA-478基板です。この2
基板は同等部品です。
2
1
6
3
(Note 2)
5
7
17
10
13
11
14
15
16
12
9
(Note 3)
8
4
Overall Section-2
(See Page 2-5)
#107
(Note 1)
#2
#69
#69
#11
#11
#11
#11
MIC901
#2
#2
#2
#281
#281
#2
#2
#2
#2
#2
#11
#2
3
2
4
1-2
1-1
3
-1
3-2
EVF Section
(See Page 2-4)
Note 3: Servicing board of the GP-1010 board is the GP-1002
board. They are equality boards.
Note 3: GP-1010基板のサービス用基板はGP-1002基板です。この2
基板は同等部品です。
NEX-VG30/VG30E/VG30EH/VG30EM/VG30H_L2
2-4
2-1-2. EVF SECTION
Screw
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
3-078-890-11
4.0
1.7
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
X-2549-590-1 HINGE
ASSY,
VF
52
1-886-654-11
FP-2038 FLEXIBLE BOARD
53
4-257-557-01 CABINET,
VF
54
A-1902-811-A
VF-1002 BOARD, COMPLETE
55
4-437-472-01
HEAT SINK, VF
56
4-437-473-01
SHEET (VF), RADIATION
57
4-446-655-01 SHEET
VF
58
X-2585-386-1 LENS (456) ASSY, VF
59
A-1902-812-A FP-2005 FLEXIBLE BOARD, COMPLETE
60
X-2585-387-1 EYE CUP (456) ASSY
61
4-437-475-01
WINDOW, EYE SENSOR
62
4-437-471-01 COVER,
EYEPIECE
LCD902 8-753-399-57 ECX331AA-3
(Note)
#11
3-078-890-11 SCREW,
TAPPING
#59
3-080-205-21 SCREW,
TAPPING,
P2
#59: M2.0 X 5.0 (Tapping)
(Silver)
3-080-205-21
3-080-205-21
5.0
2.0
#11
#59
52
60
62
LCD902
(Note)
(Note)
#11
53
58
55
54
51
61
#11
56
57
(Claws)
(Claws)
59
Note
Note: Refer to “1-3. NOTES FOR REPLACING THE EVF DISPLAY
DEVICE (LCD902) OR THE VC-1011 BOARD” on page 1-1.
Note: 1-5ページの“1-3. EVF表示素子（LCD902）またはVC-1011基
板交換時の注意”を参照してください。
Click on the first or last page to see other NEX-VG30 / NEX-VG30E / NEX-VG30EH / NEX-VG30EM / NEX-VG30H (serv.man2) service manuals if exist.