Sony ILCE-QX1 / ILCE-QX1L Service Manual ▷ View online
ILCE-QX1/QX1L
4-8
4-3-5. CLEANING PROCEDURE OF OLPF
OLPF
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull
up straight.
* Do not slide from right to left or up and down while
dabbing.
3. Repeat “3” several times to clean up.
4. According to the service manual, check if there is dirt
on the OLPF.
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull
up straight.
* Do not slide from right to left or up and down while
dabbing.
3. Repeat “3” several times to clean up.
4. According to the service manual, check if there is dirt
on the OLPF.
Cut
EE3310
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by
the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after
wrapping the cleaning cloth (J-6082-636-A) around the
cleaning jig (J-6082-635-A).
CleaningCloth
(J-6082-636-A)
(J-6082-636-A)
CleaningJig
(J-6082-635-A)
(J-6082-635-A)
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1
1. Put the two cleaning cloths on a tray like below.
1
Souse the one cleaning cloth in ethyl alcohol.
2
Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth
of 1 5 or 6 times.
*Do not slide the tip from right to left or up and down
while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth
of 2 5 or 6 times.
*Do not slide from right to left or up and down while
dabbing.
4. Wait until the tip will be dried completely.
of 1 5 or 6 times.
*Do not slide the tip from right to left or up and down
while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth
of 2 5 or 6 times.
*Do not slide from right to left or up and down while
dabbing.
4. Wait until the tip will be dried completely.
2
The dry cleaning cloth.
1
Souse the cleaning
cloth in ethyl alcohol.
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure
to clean the CCD Cleaning Jig (Tip) below before using,
please.
Note: Protection sheet is for preventing the scratch of a
surface on the Jig (Tip).
The protection sheet may be come off the Jig
when you take the Jig from a bag, but it is no
problem.
If you use the new Jig (J-6082-663-A) below, make sure
to clean the CCD Cleaning Jig (Tip) below before using,
please.
Note: Protection sheet is for preventing the scratch of a
surface on the Jig (Tip).
The protection sheet may be come off the Jig
when you take the Jig from a bag, but it is no
problem.
Protection Sheet
CCD Cleaning
Jig (Tip)
Jig (Tip)
CCD Cleaning
Jig
Jig
CCD Cleaning Jig (New)
(J-6082-663-A)
(J-6082-663-A)
ILCE-QX1/QX1L
5-1
5. ADJUSTMENT
(ENGLISH)
For adjusting these models, the Adjust station and the Adjust manual are required.
Adjust station
It is the software to start up Adjust manual for each model.
The installer of the Adjust station and the installation manual are attached, be sure to confirm the contents of them.
The installer of the Adjust station and the installation manual are attached, be sure to confirm the contents of them.
Adjust manual
It is the software to adjust and check digital cameras and camcorders for service.
The installer of the Adjust manual and the installation manual are attached, be sure to confirm the contents of them.
The installer of the Adjust manual and the installation manual are attached, be sure to confirm the contents of them.
Note 1: Be sure to install Adjust station first.
Note 2: To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed.
Note 2: To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed.
Install the Adjust manual of the DSC-WX50 series in advance.
(JAPANESE)
これらの機種で調整を行なうには,アジャストステーションとアジャストマニュアルが必要です。
アジャストステーションとは
機種別のアジャストマニュアルを起動するためのソフトウェアです。
アジャストステーションのインストーラと一緒に,インストレーションマニュアルが付いていますので,内容を必ず確認して
ください。
アジャストステーションのインストーラと一緒に,インストレーションマニュアルが付いていますので,内容を必ず確認して
ください。
アジャストマニュアルとは
デジタルカメラ及びカムコーダのサービス用の調整ソフトウェアで,調整及び各種動作確認を行うことが可能です。
アジャストマニュアルのインストーラと一緒に,インストレーションマニュアルが付いていますので,内容を必ず確認してく
ださい。
アジャストマニュアルのインストーラと一緒に,インストレーションマニュアルが付いていますので,内容を必ず確認してく
ださい。
注意1: インストールは必ず Adjust station を先に行なってください。
注意2: この機種で仕向け設定を行うには,DSC-WX50シリーズの Adjust manual がインストールされている必要
注意2: この機種で仕向け設定を行うには,DSC-WX50シリーズの Adjust manual がインストールされている必要
があります。
先に DSC-WX50 シリーズの Adjust manual をインストールしてください。
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
1.1
1.1
2014.09
2014.10
2014.10
Official Release
Revised-1
(A1 14-082)
Revised-1
(A1 14-082)
—
• Change of REPAIR PARTS LIST.
Page
Page
1-2
,
1-3
• Change of DISASSEMBLY & ASSEMBLY.
Page
Page
4-3
,
4-4
,
4-7
—
Yes
Revision History
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
1.1
1.1
2014.09
2014.10
2014.10
Official Release
Revised-1
(A1 14-082)
Revised-1
(A1 14-082)
—
• Change of REPAIR PARTS LIST.
Page
Page
1-2
,
1-3
• Change of DISASSEMBLY & ASSEMBLY.
Page
Page
4-3
,
4-4
,
4-7
—
Yes
Revision History