Sony ILCE-QX1 / ILCE-QX1L Service Manual ▷ View online
ILCE-QX1/QX1L
1-5
1-1-4. Imager Block Section
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
151
A-1954-964-A SERVICE, MECHA DEVICE (1100)
(
Note 2 on the next page
)
152
4-430-446-01
SHEET (IS) (720), RADIATION
* 153
Selection Parts IM WASHER (A), ADJUST (
Note 1 on the next page
)
* 154
Selection Parts IM WASHER (B), ADJUST (
Note 1 on the next page
)
* 155
Selection Parts IM WASHER (C), ADJUST (
Note 1 on the next page
)
156
A-1905-698-A MB CHARGE UNIT (762)
157
1-492-255-11
SHUTTER UNIT (H129)
158
A-1932-986-A MB N HOLDER ASSY (SERVICE 762)
* 160
4-186-538-01
SPRING, LENS LOCK
161
X-2586-035-1 MB L LOCK PIN ASSY (762)
* 162
4-185-963-01
MB N PLATE SP
163
4-284-623-01
MB N PLATE (B) 755
164
4-283-999-03
MB N PLATE A (754)
165
4-188-536-01
CAP, BODY (
Note 3 on the next page
)
#9
3-078-890-21 SCREW,
TAPPING
#197
4-185-990-01
MB SCREW, CHARGE UNIT FIXED
#230
4-287-434-01
TAPPING (1.7 (ECOLOGY))
152
153
(Note 1 on the
next page)
next page)
(Note 3 on the
next page)
next page)
(Note 2 on the next page)
(Note 1 on the
next page)
next page)
(Note 1 on the
next page)
next page)
154
155
156
157
163
164
165
158
160
161
ns
Imager Unit Section
(See page 1-7)
151
#9
#197
#230
#9
ns
162
ILCE-QX1/QX1L
1-6
Note 3: The Mecha Device (SERVICE) includes a protective BODY
CAP.
This part is supplied only with the Mecha Device (SER-
VICE).
VICE).
Note 3: Mecha Device (SERVICE) には保護用のボディキャップ
が含まれます。
この部品はMecha Device (SERVICE) のみに付属されま
す。
Selection Parts
Ref. No.153
Select the optimum thickness of washer.
Part
No.
Description
* 4-185-995-01 IM WASHER (A), ADJUST (t = 0.05)
* 4-185-995-11 IM WASHER (A), ADJUST (t = 0.1)
* 4-185-995-21 IM WASHER (A), ADJUST (t = 0.15)
* 4-185-995-31 IM WASHER (A), ADJUST (t = 0.2)
* 4-185-995-41 IM WASHER (A), ADJUST (t = 0.25)
* 4-185-995-51 IM WASHER (A), ADJUST (t = 0.3)
* 4-185-995-61 IM WASHER (A), ADJUST (t = 0.35)
* 4-185-995-71 IM WASHER (A), ADJUST (t = 0.4)
* 4-185-995-81 IM WASHER (A), ADJUST (t = 0.45)
* 4-185-995-91 IM WASHER (A), ADJUST (t = 0.495)
* 4-185-995-11 IM WASHER (A), ADJUST (t = 0.1)
* 4-185-995-21 IM WASHER (A), ADJUST (t = 0.15)
* 4-185-995-31 IM WASHER (A), ADJUST (t = 0.2)
* 4-185-995-41 IM WASHER (A), ADJUST (t = 0.25)
* 4-185-995-51 IM WASHER (A), ADJUST (t = 0.3)
* 4-185-995-61 IM WASHER (A), ADJUST (t = 0.35)
* 4-185-995-71 IM WASHER (A), ADJUST (t = 0.4)
* 4-185-995-81 IM WASHER (A), ADJUST (t = 0.45)
* 4-185-995-91 IM WASHER (A), ADJUST (t = 0.495)
Ref. No.154
Select the optimum thickness of washer.
Part
No.
Description
* 4-185-998-01 IM WASHER (B), ADJUST (t = 0.05)
* 4-185-998-11 IM WASHER (B), ADJUST (t = 0.1)
* 4-185-998-21 IM WASHER (B), ADJUST (t = 0.15)
* 4-185-998-31 IM WASHER (B), ADJUST (t = 0.2)
* 4-185-998-41 IM WASHER (B), ADJUST (t = 0.25)
* 4-185-998-51 IM WASHER (B), ADJUST (t = 0.3)
* 4-185-998-61 IM WASHER (B), ADJUST (t = 0.35)
* 4-185-998-71 IM WASHER (B), ADJUST (t = 0.4)
* 4-185-998-81 IM WASHER (B), ADJUST (t = 0.45)
* 4-185-998-91 IM WASHER (B), ADJUST (t = 0.495)
* 4-185-998-11 IM WASHER (B), ADJUST (t = 0.1)
* 4-185-998-21 IM WASHER (B), ADJUST (t = 0.15)
* 4-185-998-31 IM WASHER (B), ADJUST (t = 0.2)
* 4-185-998-41 IM WASHER (B), ADJUST (t = 0.25)
* 4-185-998-51 IM WASHER (B), ADJUST (t = 0.3)
* 4-185-998-61 IM WASHER (B), ADJUST (t = 0.35)
* 4-185-998-71 IM WASHER (B), ADJUST (t = 0.4)
* 4-185-998-81 IM WASHER (B), ADJUST (t = 0.45)
* 4-185-998-91 IM WASHER (B), ADJUST (t = 0.495)
Ref. No.155
Select the optimum thickness of washer.
Part
No.
Description
* 4-185-999-01 IM WASHER (C), ADJUST (t = 0.05)
* 4-185-999-11 IM WASHER (C), ADJUST (t = 0.1)
* 4-185-999-21 IM WASHER (C), ADJUST (t = 0.15)
* 4-185-999-31 IM WASHER (C), ADJUST (t = 0.2)
* 4-185-999-41 IM WASHER (C), ADJUST (t = 0.25)
* 4-185-999-51 IM WASHER (C), ADJUST (t = 0.3)
* 4-185-999-61 IM WASHER (C), ADJUST (t = 0.35)
* 4-185-999-71 IM WASHER (C), ADJUST (t = 0.4)
* 4-185-999-81 IM WASHER (C), ADJUST (t = 0.45)
* 4-185-999-91 IM WASHER (C), ADJUST (t = 0.495)
* 4-185-999-11 IM WASHER (C), ADJUST (t = 0.1)
* 4-185-999-21 IM WASHER (C), ADJUST (t = 0.15)
* 4-185-999-31 IM WASHER (C), ADJUST (t = 0.2)
* 4-185-999-41 IM WASHER (C), ADJUST (t = 0.25)
* 4-185-999-51 IM WASHER (C), ADJUST (t = 0.3)
* 4-185-999-61 IM WASHER (C), ADJUST (t = 0.35)
* 4-185-999-71 IM WASHER (C), ADJUST (t = 0.4)
* 4-185-999-81 IM WASHER (C), ADJUST (t = 0.45)
* 4-185-999-91 IM WASHER (C), ADJUST (t = 0.495)
Note 1: The IM adjust washers (A, B, C) differ in thickness.
Make sure to return the removed IM adjust washers to
original places.
original places.
When replacing IM adjust washers, refer to “Selection
Parts”.
Parts”.
If the original state cannot be restored due to loss of the
IM adjust washer, for example, replace the Mecha Device
(SERVICE).
IM adjust washer, for example, replace the Mecha Device
(SERVICE).
Note 2: Precautions for Replacement of the Mecha Device
As Mecha Device may be damaged by static electricity
from its structure, handle it carefully like for the MOS IC.
from its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
dusts nor exposed to strong light.
Note 1: IM調整ワッシャ (A, B, C) は,それぞれ厚さが異なります。
取り外したIM調整ワッシャは,必ず元の位置に戻してくだ
さい。
さい。
また,IM調整ワッシャを交換する際は, Selection Parts
を参照してください。
を参照してください。
IM調整ワッシャを紛失するなどして元の状態に戻せなく
なった場合は,Mecha Device (SERVICE) を交換してく
ださい。
なった場合は,Mecha Device (SERVICE) を交換してく
ださい。
Note 2: Mecha Device 交換時の注意
Mecha Deviceは構造上,静電気により破壊される恐れが
あるため,MOS ICと同様に注意して取り扱ってください。
あるため,MOS ICと同様に注意して取り扱ってください。
また,受光部にはゴミの付着,および強い光が入ること
のないように注意してください。
ILCE-QX1/QX1L
1-7
1-1-5. Imager Unit Section
ns: not supplied
Ref. No.
Part No.
Description
201
4-281-914-01
IM SPACER (869)
202
4-281-915-01 IM
GS
TAPE
203
1-856-482-11
FILTER BLOCK, OPTICAL (
Note on the next page
)
#191
4-188-735-01
SCREW (M1.7)
ns
201
202
202
203
(Note on the
next page)
next page)
#191
ns
(All mounted parts and IS-1007 complete
board are not supplied, but they are included
in Service, Mecha Device (1100)
(All mounted parts and IS-1007 complete
board are not supplied, but they are included
in Service, Mecha Device (1100)
ILCE-QX1/QX1L
1-8
Note :
J-6082-737-A
Imager
Peel off the release paper.
Optical Filter Block
IM Spacer
Refer to the following statements when replacing the Optical
filter block.
filter block.
Method of Removal
(1) Pour resolvent (alcohol or cleaning agent) between the
imager and the IM spacer.
*
(1) Pour resolvent (alcohol or cleaning agent) between the
imager and the IM spacer.
*
Wait for that the adhesive power of the IM spacer
weakens.
(2) Remove the IM spacer from the imager.
(2) Remove the IM spacer from the imager.
Pour resolvent (alcohol or
cleaning agent) between
the imager and the IM spacer.
cleaning agent) between
the imager and the IM spacer.
Method of Attachment
(1) Attach the two IM GS tapes and the Optical filter block
by aligning them with the outer shape of the IM spacer
evenly.
*
(1) Attach the two IM GS tapes and the Optical filter block
by aligning them with the outer shape of the IM spacer
evenly.
*
Confirm the mounting direction of the Optical filter
block referring to "4-3-4. Complementary Information".
Peel off the
release paper
release paper
Peel off the
release paper
release paper
Peel off the
release paper
release paper
Peel off the
release paper
release paper
IM GS Tape
IM GS Tape
(2) Set the Optical filter block in its attachment jig
(J-6082-737-A), with the attached adhesive side of IM
GS TAPE facing upward.
(3) Press the imager down into the jig as shown below to
attach it to the Optical filter block.
(J-6082-737-A), with the attached adhesive side of IM
GS TAPE facing upward.
(3) Press the imager down into the jig as shown below to
attach it to the Optical filter block.
Note :
J-6082-737-A
イメージャとIM間隔板の間に溶剤
(アルコールまたはクリーニング液)
を流し込む。
(アルコールまたはクリーニング液)
を流し込む。
組み付け方
(1) IM間隔板に対し,上下左右が均一になるようにIM GS TAPE
(1) IM間隔板に対し,上下左右が均一になるようにIM GS TAPE
2枚および光学フィルタブロックを貼り付ける。
* "4-3-4. Complementary Information"を参照し,
光学フィルタブロックの取り付ける向きを確認してくだ
さい。
剥離紙を剥がす
剥離紙を剥がす
剥離紙を剥がす
IM間隔板
IM GS TAPE
剥離紙を剥がす
IM GS TAPE
(2) IM GS TAPEの粘着面が上になるように,光学フィルタブロ
ック貼付け治具(J-6082-737-A)にセットする。
(3) イメージャを図のように治具に押え付け,光学フィルタブ
ロックに貼り付ける。
イメージャ
剥離紙を剥がす
光学フィルタブロック
光学フィルタブロックを交換する際は,下記を参照してくだ
さい。
さい。
取り外し方
(1) イメージャとIM間隔板の間に溶剤(アルコールまたはク
(1) イメージャとIM間隔板の間に溶剤(アルコールまたはク
リーニング液)を流し込む。
* IM間隔板の粘着力が弱くなるのを待ってください。
(2) イメージャからIM間隔板を取り外す。
Click on the first or last page to see other ILCE-QX1 / ILCE-QX1L service manuals if exist.