Sony ILCE-6000 / ILCE-6000L / ILCE-6000Y (serv.man2) Service Manual ▷ View online
ILCE-6000/6000L/6000Y_L2
2-7
2-1-4. JC BASE & BT FRAME SECTION
DISASSEMBLY
1. Remove in numerical order (
1
to
2
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇
: Solder
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
1
#308 X 1
#308
Back View
2
#308 X 1
#308
Back View
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
#308: M1.7 X 3.5 (Tapping)
(Black)
4-300-115-01
4-300-115-01
3.5
1.7
MIC901
MIC902
ANT901
ANT7381
C901
BT901
151
154
(Note 2)
157
2
158
1
163
156
152
(Note 1)
153
161
159
160
162
155
#308
#308
#2
#2
Imager Block Section
(See page 2-8)
Note 1: Refer to “Assembly-2: Installing the ST-1018 flexible board”.
Note 1: “Assembly-2: Installing the ST-1018 flexible board”を参照し
てください。
Note 2: Refer to “Assembly-3: Installing the RL-1024 flexible
board”.
Note 2: “Assembly-3: Installing the RL-1024 flexible board”を参照し
てください。
151
4-535-624-01
MIC CUSHION (775)
152
A-2038-264-A ST-1018 FLEXIBLE BOARD, COMPLETE (Note 1)
153
4-438-752-01 SHEET,
CAPACITOR
154
A-2038-263-A RL-1024 FLEXIBLE BOARD, COMPLETE (Note 2)
155
4-533-109-01
JCB GND PLATE (775)
156
X-2589-736-1 RL BASE ASSY (775)
157
4-535-830-01
STRAP PLATE (775)
158
X-2589-180-1 BT FRAME ASSY (775)
159
4-456-053-01
LIGHT (CHG) (762), GUIDE
160
1-889-866-11
BT-2011 FLEXIBLE BOARD
161
A-2038-261-A CN-1027 BOARD, COMPLETE
162
1-886-854-11
FP-2045 FLEXIBLE BOARD
163
X-2589-181-1 JACK COVER BASE ASSY(775) (BK) (BLACK)
163
X-2589-182-1 JACK COVER BASE ASSY(775) (SI) (SILVER)
163
X-2590-980-1 JACK COVER BASE ASSY (775) (WH) (WHITE)
MIC901 1-542-721-71 MICROPHONE
BLOCK
MIC902 1-542-721-71 MICROPHONE
BLOCK
* ANT7381 1-754-863-11 ANTENNA
ANT901 A-1975-721-A ANTENNA (SERVICE), NFC
ANT901 A-1975-721-A ANTENNA (SERVICE), NFC
BT901
1-780-858-11
TERMINAL BOARD BATTERY
C901
1-118-063-11
CAP, ALUMINIUM ELECT 78uF 330V
#2
2-635-562-31 SCREW(M1.7)
#308
4-300-115-01
TAPPING (1.7) (CH)
Note
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Ver. 1.3 2014.11
ILCE-6000/6000L/6000Y_L2
2-8
2-1-5. IMAGER BLOCK SECTION
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
B
A
A
B
#197
#309
#309
#5
#309
#309
212
1
201
202
5
204
205
3
213
6
209
210
217
2
215
214
216
203
Mount Section
(See page 2-10)
Imager Unit Section
(See page 2-9)
4
211
(including CP6001 (CMOS imager)
and IS-095 complete board)
(Note 4)
and IS-095 complete board)
(Note 4)
#267
(Note 1)
(Note 1)
208
(Note 2, 3)
207
(Note 2, 3)
206
(Note 2, 3)
ns
Note
201
4-530-608-01
FRONT FRAME (775)
202
1-880-964-11
IS-076 FLEXIBLE BOARD
203
1-880-963-11
IS-075 FLEXIBLE BOARD
204
4-474-412-01
IM HEAT SINK (2000)
205
4-487-617-01
IM RADIATION SHEET (2000)
* 206
Selection Parts IM WASHER (A), ADJUST (Note 2, 3)
* 207
Selection Parts IM WASHER (B), ADJUST (Note 2, 3)
* 208
Selection Parts IM WASHER (C), ADJUST (Note 2, 3)
209
A-1987-432-A MB CHARGE UNIT (2000)
210
1-487-619-31
SHUTTER UNIT (H094)
211
A-1987-441-A SERVICE, DEVICE UNIT (2000) (SERVICE)
(including CP6001 (CMOS imager) and IS-095 complete
board) (Note 4)
212
X-2589-179-1 CABINET FRONT ASSY (775) (BK) (BLACK)
212
X-2589-296-1 CABINET FRONT ASSY (775) (SI) (SILVER)
212
X-2590-979-1 CABINET FRONT ASSY (775) (WH) (WHITE)
213
4-530-664-01
VF RADIATION PLATE (775)
214
4-535-625-01
EM EYELET TAPE (775)
215
X-2589-183-1 STRAP BRACKET (L) ASSY (775)
216
4-487-875-01
HOLDER, EYELET TRIANGLE (779)
217
4-480-795-02
BUTTON, LENS LOCK (779) (BLACK)
217
4-480-795-11
BUTTON, LENS LOCK (779) (SILVER)
217
4-480-795-21
BUTTON, LENS LOCK (779) (WHITE)
#5
3-080-204-01 SCREW,
TAPPING,
P2
#197
4-185-990-01
MB SCREW, CHARGE UNIT FIXED
#267
4-287-436-21
SCREW (M1.7) (Note 1)
#309
4-300-115-21
TAPPING (1.7) (CH)
DISASSEMBLY
1. Remove in numerical order (
1
to
6
) in the left figure.
1
#309 X 2
Back View
#309
#309
2
#309 X 1
Back View
#309
3
#309 X 1
Back View
#309
4
#309 X 1
Back View
#309
5
#267 X 3
Back View
#267
6
#5 X 2
Back View
#5
Screw
#5: M1.7 X 3.5 (Tapping)
(Black)
3-080-204-01
3-080-204-01
3.5
1.7
#197: M1.6 X 4.5 (Tapping)
(Silver)
4-185-990-01
4-185-990-01
4.5
1.6
5.0
1.7
#267: M1.7 X 5.0
(Red)
4-287-436-21
4-287-436-21
#309: M1.7 X 5.0 (Tapping)
(Black)
4-300-115-21
4-300-115-21
1.7
5.0
Note 1: Refer to “Assembly-4: Screw tightening sequence when
assembling the IM Heat Sink (2000)”.
Note 1: “Assembly-4: Screw tightening sequence when assembling
the IM Heat Sink (2000)”を参照してください。
Note 2: The IM adjust washers (A, B, C) differ in thickness. Make
sure to return the removed IM adjust washers to original
places.
places.
When replacing IM adjust washers, refer to “2-2. SELEC-
TION PARTS” on page 2-11.
TION PARTS” on page 2-11.
If the original state cannot be restored due to loss of the IM
adjust washer, for example, replace the Device Unit (2000)
Service.
adjust washer, for example, replace the Device Unit (2000)
Service.
Note 3: Refer to “Assembly-5: IM Adjust Washer (A, B, C) putting
position”.
Note 2: IM調整ワッシャ (A, B, C) は,それぞれ厚さが異なります。
取り外したIM調整ワッシャは,必ず元の位置に戻してくだ
さい。
さい。
また,IM調整ワッシャを交換する際は,2-11ページの“2-2.
SELECTION PARTS” を参照してください。
IM調整ワッシャを紛失するなどして元の状態に戻せなく
なった場合は,Device Unit (2000) Service を交換してくだ
さい。
さい。
Note 3: “Assembly-5: IM Adjust Washer (A, B, C) putting position” を
参照してください。
Note 4: Precautions for Replacement of the Device Unit (2000)
Service
As CMOS Imager may be damaged by static electricity from its
structure, handle it carefully like for the MOS IC.
structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
nor exposed to strong light.
Note 4: Device Unit (2000) Service交換時の注意
CMOSイメージャは構造上,静電気により破壊される恐れが
あるため,MOS ICと同様に注意して取り扱ってください。
また,受光部にはゴミの付着,および強い光が入ることのな
いように注意してください。
いように注意してください。
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Ver. 1.3 2014.11
ILCE-6000/6000L/6000Y_L2
2-9
2-1-6. IMAGER UNIT SECTION
ns: not supplied
Screw
Ref. No.
Part No.
Description
3.5
1.7
#191: M1.7 X 3.5
(Black)
4-188-735-01
4-188-735-01
253
252
(Note)
251
#191
(All mounted parts and IS-095 complete board are not supplied,
but they are included in Device Unit (2000) Service)
but they are included in Device Unit (2000) Service)
ns
ns
Note
Note:
(1)
Refer to the following when assembling the Glass Assy
and the Imager.
and the Imager.
Attach the Glass Assy, IM Spacer Plate, Glass Retainer Assy,
and to the IM Imager Plate.
and to the IM Imager Plate.
(2) Set the parts assembled in step (1) and the Imager onto
the optical filter block attachment jig (J-6082-737-A) while
aligning them with two pins.
aligning them with two pins.
(3) Secure the Imager with four screws.
Optical filter block attachment jig
J-6082-737-A
Parts assembled
in step (1)
in step (1)
Imager
Pin
Pin
Glass Retainer Assy
Glass Assy
IM Spacer Plate
IM Imager Plate
Note: ガラスASSYとイメージャを組み立てる際は,下記を参照
してください。
(1) IM イメージャ台板に,ガラスASSY,IM 間隔板,ガラス押さえ
ASSY
を取り付ける。
IM
イメージャ台板
IM
間隔板
ガラス ASSY
ガラス押さえ ASSY
(2)
ピン2箇所で位置を合わせて,(1)で取り付けた部品とイメージャ
を,光学フィルタブロック貼り付け治具(J-6082-737-A)にセット
する。
を,光学フィルタブロック貼り付け治具(J-6082-737-A)にセット
する。
(3)
ねじ4本でイメージャを固定する。
光学フィルタブロック貼り付け治具
J-6082-737-A
J-6082-737-A
(1)
で取り付けた部品
イメージャ
ピン
ピン
251
A-2045-073-A GLASS RETAINER ASSY SERV (2000) (SERVICE)
252
A-2045-072-A INDIVIDUAL, GLASS ASSY (2000) (SERVICE) (Note)
253
4-487-615-01
IM SPACER PLATE (2000)
#191 4-188-735-01 SCREW
(M1.7)
ILCE-6000/6000L/6000Y_L2
2-10
2-1-7. MOUNT SECTION
ns: not supplied
Ref. No.
Part No.
Description
Screw
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
3-078-890-11
4.0
1.7
305
(Note 1)
306
304
(Note 4)
307
308
309
303
302
(Note 3)
301
(Note 2)
ns
#11
Note
301
4-188-536-01
CAP, BODY (Note 2)
302
4-283-999-03
MB N PLATE A (754) (Note 3)
303
4-284-623-01
MB N PLATE (B) 755
* 304
4-185-963-01
MB N PLATE SP (Note 4)
305
A-1987-420-A MB N CONTACT UNIT (2000) (Note 1)
306
4-530-624-01
THERMAL SHEET G (775)
307
4-484-357-01
HOLDER, LENS LOCK (3000)
* 308
4-186-538-01
SPRING, LENS LOCK
309
X-2586-035-1 MB L LOCK PIN ASSY (762)
#11
3-078-890-11 SCREW,
TAPPING
Note 1:
Hold the MB N Contact Unit (2000)
at the center of both sides.
at the center of both sides.
Hold here.
Don't touch this part.
Note 1:
MB N Contact Unit (2000)
の両側の
中央部を持ってください。
ここを持ってください。
この部分には触れないでください。
Note 3: Refer to “Assembly-6: Screw tightening sequence when
assembling the MB N Plate A (754)”.
Note 4: Refer to “Assembly-7: Apply grease on the MB N Plate SP”.
Note 3: “Assembly-6: Screw tightening sequence when assembling
the MB N Plate A (754)”を参照してください。
Note 4: “Assembly-7: Apply grease on the MB N Plate SP”を参照し
てください。
Note 2: The Device Unit (2000) Service includes a protective the Body
Cap.
This part is supplied only with the Device Unit (2000) Service.
Note 2: Device Unit (2000) Serviceには保護用のボディキャップが含
まれます。
この部品はDevice Unit (2000) Serviceのみに付属されます。
Click on the first or last page to see other ILCE-6000 / ILCE-6000L / ILCE-6000Y (serv.man2) service manuals if exist.