Sony ILCE-6000 / ILCE-6000L / ILCE-6000Y (serv.man2) Service Manual ▷ View online
ILCE-6000/6000L/6000Y_L2
2-3
– JAPANESE –
– ENGLISH –
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
DISCHARGING OF THE CHARGING
CAPACITOR (C901)
CAPACITOR (C901)
The charging capacitor is charged up to the maximum 330 V
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω/1 W
Wrap insulating tape.
1 k
Ω/1 W
Wrap insulating tape.
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け,
折れ等がないことを確認する。
また,コネクタへの接続は,差し込み不足や斜め差しになら
ないように注意する。
• コネクタを取り外す時に,線材部(極細)を持って引っ張ると
断線する恐れがありますので,絶対に線材部(極細)を持って
引っ張らないでください。
引っ張らないでください。
• 線材部(極細)を押さえながらコネクタを差し込むと,線材部
(極細)が断線する恐れがありますので,絶対に線材部(極細)
には負担をかけないでください。
• 金メッキされているフレキシブル基板には,強い負担をかけ
ないでください。
ストロボ用充電コンデンサ (C901) の放電
ストロボ用充電コンデンサは最大330 Vの電圧で充電さ
れています。
この高電圧で充電されたコンデンサに手を触れた場合,
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
れています。
この高電圧で充電されたコンデンサに手を触れた場合,
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
ショート治具の準備
ショート治具は1kΩ/1W抵抗 (1-215-869-11)
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
R:
1 kΩ/1 W
((Part code: 1-215-869-11)
コンデンサの放電
フラッシュユニットの電源コンデンサ
の端子間をショート治具で約10秒間
接続する。
フラッシュユニットの電源コンデンサ
の端子間をショート治具で約10秒間
接続する。
ST-1018 Flexible Board
ST-1018 Flexible Board
C901
R:
1 kΩ/1 W
(
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.
Short-circuit between two points with
the short jig about 10 seconds.
(Part code: 1-215-869-11)
ST-1018 Flexible Board
ST-1018 Flexible Board
C901
SUBSIDIARY MATERIALS
G
: Grease
G-85 (J-6082-626-A)
⾗᧚
G
: Grease
G-85 (J-6082-626-A)
ILCE-6000/6000L/6000Y_L2
2-4
2-1. EXPLODED VIEWS
2-1-1. TOP & REAR SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
3
2
2
(Note 3)
6
5
12
4
13
7
3
5
8
6
11
9
10
14
1
4
LCD Section
(See page 2-5)
#1
#109
#140
#1
#2
#10
(Note 1)
#10
(Note 1)
#2
#308
#311
(Note 1)
#311
(Note 1)
#308
#311
(Note 1)
#311
(Note 1)
#9
#309
(Note 1)
#309
(Note 1)
#9
#309
(Note 1)
#309
(Note 1)
#2
#10
(Note 1)
#10
(Note 1)
6-3
6-1
2-1
2-2
6-2
6-2
(Hook)
(Hook)
#9
#309
(Note 1)
#309
(Note 1)
(Note 2)
(Note 4)
DISASSEMBLY
1. Remove in numerical order (
1
to
6
) in the left figure.
Right View
Top View
Bottom View
#2
#10
#10
#309
#9
#9
#109
2-1
2-2
2
#2/#10 X 1 → Popup the Strobe (
2
-1
) → #109 X 2 Open the BT Lid (
2
-2
) → #309/#9 X 2
Screw
DISCHARGING OF THE CHARGING CAPACITOR
ストロボ用充電コンデンサの放電
3
5
#309/#9 X 1
2
A-2044-430-A SERVICE BLOCK ASSY (775) (BK) (BLACK) (Note 3)
2
A-2044-432-A SERVICE BLOCK ASSY (775) (SI) (SILVER) (Note 3)
2
A-2069-609-A SERVICE BLOCK ASSY (775) (WH) (WHITE) (Note 3)
3
4-530-648-01
ST COVER (775) (BLACK)
3
4-530-648-11
ST COVER (775) (SILVER)
3
4-563-952-01
ST COVER (775) W (WHITE)
4
1-471-509-11
MAGNET (N45H) (Note 4)
5
1-490-550-11
FLASH UNIT
6
X-2589-215-1
ST ARM ASSY (775)
7
4-535-927-01
ST ARM SHEET (75)
8
4-530-649-01
ST ARM COVER (775)
9
4-533-120-01
ST BASE INSULATING SHEET (775)
10
4-533-121-01
ST FPC FIX TAPE (775)
11
X-2589-185-1 CABINET REAR ASSY (775) (BK) (BLACK)
11
X-2589-188-1 CABINET REAR ASSY (775) (SI) (SILVER)
11
X-2590-981-1 CABINET REAR ASSY (775) (WH) (WHITE)
12
4-530-645-01
DIOPTER ADJUST DIAL (775) (BLACK
, WHITE
)
12
4-530-645-11
DIOPTER ADJUST DIAL (775) (SILVER)
13
4-531-721-01
DIOPTER ADJUST DIAL SHEET (775) (BLACK
, WHITE
)
13
4-531-721-11
DIOPTER ADJUST DIAL SHEET (775) (SILVER)
14
X-2589-633-1 FINDER COVER ASSY (775)
#1
2-635-562-11 SCREW
(M1.7)
#2
2-635-562-31
SCREW (M1.7) (Note 1)
#9
3-078-890-21
SCREW, TAPPING (Note 1)
#10
2-599-475-31
SCREW (M1.7) (Note 1)
#109
2-515-483-21
SCREW (M1.7), LOCK ACE, P2
#140 2-635-562-01 SCREW
(M1.7)
#308
4-300-115-01
TAPPING (1.7) (CH) (Note 1)
#309
4-300-115-21
TAPPING (1.7) (CH) (Note 1)
#311
4-300-113-01
TAPPING (1.7) (CH) (Note 1)
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
Cabinet's Color
Table 2-1
Note 1:
THE COMBINATION OF CABINET’S COLOR
AND SCREW
AND SCREW
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to
Table 2-1.
#2/#308/#309 (Black)
#9/#10/#311 (Silver)
BLACK
SILVER
, WHITE
6
Open the Jack Lid (
6
-1
) → #309/#9 X 1 → #1 X 1 → Open the BT Lid (
6
-2
) #2 X 1 → #2/#10 X 2
Back View
#309
#9
#9
Right View
Top View
Bottom View
#309
#9
#9
#2
#2
#10
#10
#1
6-2
6-1
Open the LCD (
6
-3
) → #1 X 2
1
1
2
Right View
Open LCD at the angle
shown below.
shown below.
Back View
#1
6-3
#1: M1.7 X 2.5
(Black)
2-635-562-11
2-635-562-11
2.5
1.7
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
#9: M1.7 X 5.0 (Tapping)
(Silver)
3-078-890-21
3-078-890-21
5.0
1.7
#10: M1.7 X 4.0
(Silver)
2-599-475-31
2-599-475-31
4.0
1.7
#109: M1.7 X 3.0
(Black)
2-515-483-21
2-515-483-21
3.0
1.7
#140: M
1.7
X 2.0
(Black
)
2-635-562-01
2.0
1.7
#308: M1.7 X 3.5 (Tapping)
(Black)
4-300-115-01
4-300-115-01
3.5
1.7
#309: M1.7 X 5.0 (Tapping)
(Black)
4-300-115-21
4-300-115-21
1.7
5.0
#311: M1.7 X 3.5 (Tapping)
(Silver)
4-300-113-01
4-300-113-01
3.5
1.7
Note
Note 3: Refer to “Assembly-1: Notes on Assembling the Top cabinet
section”.
Note 3: “Assembly-1: Notes on Assembling the Top cabinet section”
を参照してください。
Note 2: Refer to “ACCESSORIES” on page 2-11.
Note 2: 2-11ページ“ACCESSORIES” を参照してください。
Install the magnet with the
marking oriented as shown
below.
marking oriented as shown
below.
Marking
Note 4:
マグネットを取り付ける際は,
マーキング面を図の位置に
合わせてください。
マーキング面を図の位置に
合わせてください。
マーキング
Note 4:
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Ver. 1.3 2014.11
ILCE-6000/6000L/6000Y_L2
2-5
2-1-2. LCD SECTION
ns: not supplied
DISASSEMBLY
1. Remove in numerical order (
1
to
2
) in the left figure.
2
#109 X 2 → #70 X 1 → #2 X 1 → #2/#10 X 1
Back View
Left View
Bottom View
#2
#10
#10
#70
#2
#109
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
A
A
Main Board Section
(See page 2-6)
ns
51
54
66
55
56
59
57
53
61
62
64
65
60
63
67
2
52
1
58
#2
#2
#10
#10
#1
#239
#239
#109
#70
#259
#139
(Note)
#139
(Note)
(Note)
#1
LCD901
51
4-530-633-01
LC FPC CAP (775)
52
4-530-628-01
MAIN FRAME (775)
53
4-537-959-01 SCREW,
TRIPOD
(775)
54
4-534-817-01
THERMAL SHEET C (775)
55
4-530-632-01
REC BUTTON HOLDER (775)
56
X-2589-184-1 STRAP BRACKET (G) ASSY (775)
57
4-487-875-01
HOLDER, EYELET TRIANGLE (779)
58
1-492-592-11
SWITCH BLOCK, CONTROL (BK77900) (BLACK)
58
1-492-592-21
SWITCH BLOCK, CONTROL (SL77300) (SILVER
,
WHITE
)
59
4-530-646-01
FRAME SHEET (775)
60
4-530-647-01
LC LIGHT INTERCEPT SHEET (775)
61
X-2589-237-1 HINGE
ASSY
(775)
62
4-438-791-01
RETAINER, LC FLEXIBLE
63
A-2038-262-A LC-1018 FLEXIBLE BOARD, COMPLETE
64
4-530-673-01
LC CABINET (REAR) (775)
65
4-532-715-01
LEVER (779), LC LOCK
66
4-533-123-01
LC LOCK HOLDER (775)
67
4-533-124-01
LC CABINET REAR PLATE (775)
LCD901 A-2044-429-A LCD SERVICE BLOCK ASSY (775 BK) (BLACK)
LCD901 A-2044-431-A LCD SERVICE BLOCK ASSY (775 SI) (SILVER)
LCD901 A-2044-431-A LCD SERVICE BLOCK ASSY (775 SI) (SILVER)
LCD901 A-2069-610-A SERVICE BLOCK ASSY (775) (WH) (WHITE)
#1
2-635-562-11 SCREW
(M1.7)
#2
2-635-562-31
SCREW (M1.7) (Note)
#10
2-599-475-31
SCREW (M1.7) (Note)
#70
2-599-475-41 SCREW
(M1.7)
#109
2-515-483-21
SCREW (M1.7), LOCK ACE, P2
#139
2-655-579-01
SCREW 0+P2 M1.4 NEWTRU-STAR (Note)
#239
4-287-435-11
SCREW (M1.4 EUROPE) TYPE
#259
4-412-769-61
SCREW (M1.4), NEW TRU-STAR, P2 (Note)
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
2-635-562-11
2.5
1.7
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
#70: M1.7 X 5.0
(Silver)
2-599-475-41
2-599-475-41
5.0
1.7
#109: M1.7 X 3.0
(Black)
2-515-483-21
2-515-483-21
3.0
1.7
#139: M1.4 X 2.0
(Silver)
2-655-579-01
2-655-579-01
2.0
1.4
#239: M1.4 X 1.4
1.4
1.4
(Red)
4-287-435-11
4-287-435-11
#259:M1.4 X 2.0
(Black)
4-412-769-61
4-412-769-61
2.0
1.4
Note
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
Cabinet's Color
Table 2-1
Note :
THE COMBINATION OF CABINET’S COLOR
AND SCREW
AND SCREW
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to
Table 2-1.
#2/#259 (Black)
#10/#139 (Silver)
BLACK
SILVER
, WHITE
#10: M1.7 X 4.0
(Silver)
2-599-475-31
2-599-475-31
4.0
1.7
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Ver. 1.3 2014.11
ILCE-6000/6000L/6000Y_L2
2-6
DISASSEMBLY
1. Remove in numerical order (
1
to
6
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇
: Solder
2-1-3. MAIN BOARD SECTION
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
(Hook)
SP901
LCD902
(Hook)
JC Base & BT Frame Section
(See page 2-7)
101
111
2
109
1
110
104
105
4
106
5
107
3
102
103
112
6
108
(Note 2)
#309
#308
#308
#2
#109
BH0200
(Note 1)
(Note 1)
ns
BT0200
(Note 1)
(Note 1)
: BT0200 (LITHIUM RECHARGEABLE
BATTERY)
Board on the mount position.
(See page 6-39 of Level 3)
BATTERY)
Board on the mount position.
(See page 6-39 of Level 3)
(Note 2)
3
#309 X 1
4
#2 X 1
#309
Back View
#2
Back View
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
#109: M1.7 X 3.0
(Black)
2-515-483-21
2-515-483-21
3.0
1.7
Note 1: Replace the battery holder (BH0200) together when
replacing the lithium storage battery (BT0200) on the SY-
1028 board. (The battery holder removed once cannot be
used again.)
1028 board. (The battery holder removed once cannot be
used again.)
When mounting these parts, mount new battery holder first
and attach new lithium storage battery next.
and attach new lithium storage battery next.
Note 1: SY-1028基板のリチウム蓄電池(BT0200) を交換する場合は
バッテリホルダ(BH0200) も同時に新品に交換してください。
(一度使用したバッテリホルダは再使用できません。)
部品取り付けの際は,先にバッテリホルダを取り付けてからリ
チウム蓄電池を装着してください。
チウム蓄電池を装着してください。
101
4-530-650-01
VF FRAME (775)
102
X-2589-613-1 VF UNIT ASSY 775
103
4-530-665-01
EYE SENSOR CUSHION (775)
104
A-1933-717-A MIS-2000 FLEXIBLE BOARD, COMPLETE (SILVER
,
WHITE
)
104
A-2038-281-A MIS-2000 FLEXIBLE BOARD, COMPLETE (BLACK)
105
4-533-122-01
SHOE SPACER (775)
106
4-530-625-01
SHOE BASE PLATE (775)
107
4-530-617-01
BT FRAME REAR (775)
108
A-2038-810-A SY-1028 BOARD, COMPLETE (SERVICE) (Note 2)
109
4-534-818-01
THERMAL SHEET S (775)
110
4-530-627-01
SY INSULATION SHEET (775)
111
4-438-854-01
SHEET, VF RADIATION A
112
4-538-030-11
VF SHEET (775)
BT0200 1-756-134-15
BATTERY, LITHIUM (SECONDARY) (Note 1)
BH0200 1-251-928-21
SOCKET, BATTERY (Note 1)
LCD902 A-2047-084-A ECX333AA-1_SERVICE (Note 2)
SP901 1-858-826-11 SPEAKER
SP901 1-858-826-11 SPEAKER
(0.8CM)
#2
2-635-562-31 SCREW(M1.7)
#109
2-515-483-21
SCREW (M1.7), LOCK ACE, P2
#308
4-300-115-01
TAPPING (1.7) (CH)
#309
4-300-115-21
TAPPING (1.7) (CH)
Note
Note 2: Refer to “1-3.NOTES FOR REPLACING THE EVF DIS-
PLAY DEVICE (LCD902) OR THE SY-1028 BOARD” on
page 1-1.
page 1-1.
Note 2: 1-3ページ “1-3.EVF表示素子(LCD902)またはSY-1028基板
交換時の注意” を参照してください。
5
#308 X 2
6
#308 X 2
#308
Back View
#308
Back View
#308: M1.7 X 3.5 (Tapping)
(Black)
4-300-115-01
4-300-115-01
3.5
1.7
#309: M1.7 X 5.0 (Tapping)
(Black)
4-300-115-21
4-300-115-21
1.7
5.0
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Ver. 1.3 2014.11
Click on the first or last page to see other ILCE-6000 / ILCE-6000L / ILCE-6000Y (serv.man2) service manuals if exist.