DOWNLOAD Sony ILCA-77M2 / ILCA-77M2M / ILCA-77M2Q Service Manual ↓ Size: 13.81 MB | Pages: 37 in PDF or view online for FREE

ILCA-77M2/77M2M/77M2Q_L2

1-2

Perform the following procedure to check the Wi-Fi function.

Required equipment: Windows personal computer with Wi-Fi interface

1.  Turn on the power of the unit.
2.  Perform the following operations for the unit.
 MENU→   →[Ctrl w/ Smartphone]→●
3.  The Ctrl w/ smartphone screen is displayed.
4.  When preparation for Wi-Fi has been completed, the “Running as an access point.” screen opens and a password for Wi-Fi connection is displayed.

SSID

 

DIRECT-XXXX:MODEL-NAME

Password

  

XXXXXXXX

Device Name

  

ILCA-XXXX

Ctrl w/ Smartphone

Operate smartphone to connect to 

this device via Wi-Fi.

Cancel

Enter

5.  Confirm on the personal computer that the unit is detected as a connectable wireless network.
6.  To further confirm that the unit is connectable, connect the unit to the personal computer and double-click the “current connection” from the icon 

displayed on the notice field, make sure that the unit is displayed in the Wireless internet access column.

Adjustment values of each EVF display device (LCD902) are stored on the AM board.
Therefore, when the LCD902 or the AM board has been replaced, write WB adjustment values.

10/11_193_26_0

Brightness value

White balance value

The label which is put on repairing EVF display device (LCD902)

When LCD902 is replaced:
1.  Check and write down the adjustment values printed on the repairing EVF display device (LCD902) label.
2.  After the LCD902 has been replaced, execute “EVF Data Input” on the ADJUST tab by using the Adjust manual to write the adjustment values.

When replacing AM board (in case adjustment values can be read):
1.  In case the unrepaired unit starts and adjustment values can be read by using the Adjust manual, execute “ADJUSTMENT DATA BACKUP” on 

the DATA tab.

2.   After the AM board has been replaced with a AM board for repair, execute “ADJUSTMENT DATA BACKUP” on the DATA tab of the Adjust 

manual to write the extracted data to the unit.

When replacing AM board (in case adjustment values cannot be read):
Consult with each Head Quarters.

ILCA-77M2/77M2M/77M2Q_L2

1-3

Make sure to confirm below after replacing the AS Slider B Assy T or the AS Holder Actuator Assy.

(1)  Remove the CV Rear Cover Assy (880), temporally mount the AS Slider Unit (863) mounted with the Imager Sensor, and then set up the camera body 

and hold the AS Slider Unit (863) as shown in figure.

 

(2)  Select “Slider Unit Check” of the adjustment software, and then confirm if the result is OK.
(3)  Select “Tebure Revise Adj.” of the adjustment software, and then confirm if the result is OK.
(4)  Mount the AS Slider Unit (863) to the camera.

 

Make sure to confirm below before replacing the AS Slider B Assy T or the AS Holder Actuator Assy.

(1)  Remove the CV Rear Cover Assy (880), and temporally mount the AS Slider Unit (863).
(2)  Set the AS Slider Unit (863) upwards as shown in figure, and put it on a stable place.

 

(3)  Select “Slider Unit Check” of the adjustment software, and then confirm the movement to the directions of Pitch and Yaw, and if an error occurs, 

replace it with the component part corresponding to the movement.

 

ILCA-77M2/77M2M/77M2Q_L2

1-4

Removal Procedure

(1)  Remove the spring.

 

Spring

(2)  Remove the solder on the enamel wires at two places.

 

Solder

Solder

(3)  Remove the flexible board from the AS Slider B Assy T.

 

Flexible Board

(4)  Remove the two screws.

 

(5)  Remove the AS Unit Holder Ball.

 

AS Unit Holder Ball

(6)  Remove the two Ball Bearings.

 

Ball Bearing

Ball Bearing

(7)  Remove the Cap SPs (for Pitch and Yaw).

 

Cap SP

(8)  Remove the Caps (for Pitch and Yaw).

 

Cap

(9)  Remove the AS Slider A.
 

It can be done easily if A is removed beforehand.

 

AS Slider A 

A

(10)  Remove the AS Slider B Assy T.
 

It can be done easily if B is removed beforehand.

 

AS Slider B Assy T

B

(11)  Remove the three Ball Bearings.

 

Ball Bearing

Assembly Procedure

Note: Make sure to perform the assembly procedures after assembling the AS Holder Actuator Assy.

The assembly procedure is the reverse of the removal procedure.
Apply grease to the portions indicated below.

 

* After applying grease, attach the Ball Bearings.

 

Ball Bearing

G G-15

 

AS Slider B Assy T

G G-15 and G G-116

 

* After applying grease, attach the Ball Bearings.

 

Ball Bearing

G G-15

Ball Bearing

G G-15

ILCA-77M2/77M2M/77M2Q_L2

1-5

Removal Procedure

Note: Make sure to perform the removal procedures after removing the 
 

 AS Slider B Assy T.

(1)  Remove the solder on the enamel wires at two places.

 

Solder

(2)  Remove the flexible board from the hook on the AS Holder Actuator 
 Assy.

 

Hook

(3)  Remove the four screws to remove the AS Holder Actuator Assy.

 

AS Holder Actuator Assy

Assembly Procedure

Note: Make sure to perform the assembly procedures before assembling  
 

 the AS Slider B Assy T.

The assembly procedure is the reverse of the removal procedure.
Apply grease to the portions indicated below.

 

AS Holder Actuator Assy

G G-15 and G G-116

If the AP Iris Ring is removed, the aperture charge cannot be retained. Therefore, after removing the AP Iris Ring, retain the charge in the procedure 
below.

(4) While keeping the pin inserted, remove the Ring Roller B and AP 

Ring Roller (C).

 

Pin

AP Ring Roller (C)

Ring Roller B 

(5)  While keeping the pin inserted, remove the AP Iris Ring.

 

Pin

AP Iris Ring

(1)  Rotate clockwise the AP Iris Ring as far as it goes.

 

AP Iris Ring

(2)  Remove the MB A Mount and MB Ring SP COM, unscrewing six 

screws.

 

MB Ring SP COM

MB A Mount

(3)  Insert the pin (approx. 1mm in diameter) through the hole of front 

frame and drop the tip of pin in the cut portion of AP Sensor Gear 
to fix the AP Sensor Gear.

Pin

Pin

Cut portion of
AP Sensor Gear

Hole of front
frame