Sony ILCA-77M2 / ILCA-77M2M / ILCA-77M2Q Service Manual ▷ View online
ILCA-77M2/77M2M/77M2Q_L2
2-17
Screw
#23: M1.7 X 4.0 (Tapping)
(Black)
3-080-204-11
3-080-204-11
4.0
1.7
#241: M1.4 X 2.5
(Black)
3-703-816-46
3-703-816-46
2.5
1.4
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
651
4-292-464-01
MB MIRROR FRAME HOLDING SP
652
A-1837-335-A MB MIRROR FRAME HOLDER ASSY (Note 1)
653
A-1855-640-A P.O.I (SERVICE) (Note 1, 2)
654
4-292-475-01
MB SHUTTER CHARGE LEVER
655
4-292-476-01
MB SHUTTER CHARGE LEVER SP
656
4-292-473-01
MB DECELERATION GEAR 1
657
4-292-474-01
MB DECELERATION GEAR 2
658
X-2582-303-1 MB SHUTTER CHARGE CAMGEAR ASSY
659
A-1837-333-A SLK FPC UNIT 870 BOARD, COMPLETE
660
4-292-574-01
MB LENS LOCK BASE PLATE
661
4-194-447-01
MB LEVER CUSHION
#23
3-080-204-11 SCREW,
TAPPING,
P2
#241
3-703-816-46
SCREW (M1.4X2.5), SPECIAL HEAD
2-1-14. MIRROR BOX SECTION (SUB UNIT-2)
ns: not supplied
ns
ns
ns
ns
#23
#241
#23
#23
#23
652
(Note 1)
653
(Note 1, 2)
651
657
658
656
655
661
660
654
659
(including M903 (charge motor) and
SLK-009 flexible board)
SLK-009 flexible board)
Note
Note 2: Refer to “1-1. METHOD FOR REPLACING THE P.O.I.” on
page 1-1 when replacing the P.O.I. without disassembling
the camera.
the camera.
Note 2: 分解を行わずにP.O.I.のみ交換する場合,1-7 ページの “1-1.
P.O.I.の交換方法” を参照してください。
Note 1: If the MB Mirror Frame Holder Assy (P.O.I.) is raised and
then pushed from the front side with the Shutter Unit (AFE-
3111) and the AS Slider Unit (863) have been removed, it
may drop off behind and get scratched or damaged.
3111) and the AS Slider Unit (863) have been removed, it
may drop off behind and get scratched or damaged.
Note 1: シャッターユニット(AFE-3111),ASスライダーユニット(863)
を取り外した状態でMBミラー枠ホルダー Assy(P.O.I.)をアッ
プさせ,正面より押した場合,後ろへ抜け落ちてキズや破損
の恐れがあります。
プさせ,正面より押した場合,後ろへ抜け落ちてキズや破損
の恐れがあります。
ILCA-77M2/77M2M/77M2Q_L2
2-18E
ACCESSORIES
901
902
903
904
905
906
907
908
909
910
911
912
913
914
Ref. No. Part No.
Description
901
1-489-761-11
BC-VM10A Battery charger (J)
901
1-489-761-21
BC-VM10A Battery charger (US, CND)
901
1-489-761-62
BC-VM10A Battery charger (EXCEPT US, CND, J)
902
1-837-424-11
Power cord (mains lead) (E: NTSC)
902
1-837-427-11
Power cord (mains lead) (AEP, UK, RU, AUS, E: PAL)
902
1-837-428-12
Power cord (mains lead) (KR)
902
1-838-719-11
Power cord (mains lead) (CH)
902
1-848-142-11
Power cord (mains lead) (IND)
903
1-569-007-31
Conversion (2P) Adaptor (E: NTSC)
904
1-569-008-12
Conversion (2P) Adaptor (AUS, E: PAL)
905
1-846-615-12
Micro USB cable
906
4-535-925-01 Shoulder
strap
907
4-141-107-12 Body
cap
908
4-438-734-01 Shoe
cap
909
X-2582-324-1 Eyepiece
Cup
Ref. No.
Part No.
Description
910
X-2582-781-1 Front lens cap (ILCA-77M2M)
911
2-683-615-01
Rear lens cap (ILCA-77M2M)
912
4-294-806-01
Lens hood (ILCA-77M2M)
913
4-290-649-01
Lens hood (ILCA-77M2Q)
914
4-536-323-02
Instruction Manual (JAPANESE)
* 914
4-536-323-11
Instruction Manual (ENGLISH)
* 914
4-536-323-21
Instruction Manual (FRENCH)
* 914
4-536-323-31
Instruction Manual (SPANISH, PORTUGUESE)
* 914
4-536-323-41
Instruction Manual (ENGLISH, FRENCH, GERMAN,
SPANISH, ITALIAN, PORTUGUESE, DUTCH, POLISH,
RUSSIAN, UKRAINIAN, SWEDISH, FINNISH,
NORWEGIAN, DANISH)
SPANISH, ITALIAN, PORTUGUESE, DUTCH, POLISH,
RUSSIAN, UKRAINIAN, SWEDISH, FINNISH,
NORWEGIAN, DANISH)
* 914
4-536-323-51
Instruction Manual (TRADITIONAL CHINESE,
SIMPLIFIED CHINESE)
SIMPLIFIED CHINESE)
* 914
4-536-323-61
Instruction Manual (ARABIC, PERSIAN)
* 914
4-536-323-71
Instruction Manual (KOREAN)
* 914
4-536-323-82
Instruction Manual (SIMPLIFIED CHINESE)
Ref. No. Part No.
Description
8-021-911-00
Rechargeable battery pack NP-FM500H/J (J)
8-021-911-32
Rechargeable battery pack NP-FM500H/UC (US, CND)
8-021-911-52
Rechargeable battery pack NP-FM500H/CE (EXCEPT US, CND, CH, J)
8-021-911-73
Rechargeable battery pack NP-FM500H/CN (CH)
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2015.08
ILCA-77M2/77M2M/77M2Q_L2
3-1
3. ASSEMBLY
Assembly-1: Routing of the Flash Harness
Flash Harnesses
Ribs
Assembly-2: Notes on Assembling the ALX-8800 (AF Module)
A
Tighten the S Adjustment Screws completely.
B
Loosen the S Adjustment Screws evenly by 0.5 turns.
Assembly-3: Notes on Installing the Shutter Unit (AFE-3111)
When install Shutter Unit (AFE-3111), check MB Shutter Charge
Lever is downward.
Lever is downward.
Shutter Unit
(AFE-3111)
(AFE-3111)
MB Shutter
Charge Lever
Charge Lever
4-3. MB Ring SP COM, MB A Mount
MB Ring SP COM
MB A Mount
GG-85
3
6
1
4
2
5
Tighten six screws in order of the number.
4-4. AP Sensor Gear Setting Position
AP Sensor Gear
Hole
AP Sensor Gear
4-5. Gears Setting Position
MB Shutter
Charge Lever SP
Charge Lever SP
MB Lever
Cushion
Cushion
MB Deceleration
Gear 1
Gear 1
MB Deceleration
Gear 2
Gear 2
MB Shutter
Charge Level
Charge Level
MB Shutter Charge
Camgear Assy
Camgear Assy
Assembly-5: How to distinguish the side of Optical Filter Block
facing to Imager
'LVWLQJXLVKLQJWKH89,5FRDWHGVXUIDFHDQG
$5FRDWHGVXUIDFHRIWKH2SWLFDOILOWHUEORFN
2SWLFDOILOWHUEORFNPRXQWLQJGLUHFWLRQ
Optical Filter
Block
Block
Reflected in red
89,5FRDWHGVXUIDFH
89,5FRDWHGVXUIDFH
$5FRDWHGVXUIDFH
$5FRDWHGVXUIDFH
Shed light obliquely on the Optical filter block
Optical Filter Block
Optical Filter
Block
Block
Imager side
Mount side
Assembly-4: Notes on Assembling the Mirror Box Sub Unit
4-1. Ring Roller A (SV), AP Iris Ring
A
Attach the Ring Roller A (SV) to the MB Front Frame Assy.
When attaching the Ring Roller A (SV), be sure to remove the AP Iris Ring
beforehand.
beforehand.
B
Attach the AP Iris Ring by aligning it with the stop position (iris-in end) of
drawing.
Stop Position (iris-in end)
Ring Roller A (SV)
Ring Roller A (SV)
AP Iris Ring
4-2. Ring Roller (B) , Ring Roller (C), Ring Roller (C) Shaft
AP Iris Ring
Ring Roller (B)
Ring Roller (B)
GG-85
Ring Roller (C) Shaft
Ring Roller (C)
AP Iris Ring
Ring Roller (C) Shaft
Ring Roller (C)
Ring Roller (C)
Ring Roller (C) Shaft
Ring Roller (C) Shaft
ILCA-77M2/77M2M/77M2Q_L2
3-2E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
* Do not slide from right to left or up and down while dabbing.
3. Repeat “3” several times to clean up.
4. According to the service manual, check if there is dirt on the OLPF.
4. According to the service manual, check if there is dirt on the OLPF.
CCD Cleaning Jig (New)
(J-6082-663-A)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1. Put the two cleaning cloths on a tray like below.
1
Souse the one cleaning cloth in ethyl alcohol.
2
Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
* Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
* Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
1
Souse the cleaning
cloth in ethyl alcohol.
cloth in ethyl alcohol.
2
The dry cleaning cloth.
OLPF
Mirror Lock Lever
Cleaning Jig
(J-6082-635-A)
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
(J-6082-636-A)
Cut
EE3310
Click on the first or last page to see other ILCA-77M2 / ILCA-77M2M / ILCA-77M2Q service manuals if exist.