Sony DSLR-A560 / DSLR-A560L / DSLR-A560Y / DSLR-A580 / DSLR-A580J / DSLR-A580L / DSLR-A580Y Service Manual ▷ View online
DSLR-A560/A560L/A560Y/A580/A580L/A580Y/A580J_L2
1-2
1-4. METHOD FOR ADJUSTING THE TEBURE REVISE
Make sure to confirm below after replacing the AS Slider B Assy or the AS Holder Actuator Assy.
(1) Remove the CV Rear Cover Assy (865), temporally mount the AS Slider Unit (863) mounted with the Imager Sensor, and then set up the camera
body and hold the AS Slider Unit (863) as shown in figure.
(2) Select “Slider Unit Check” of the adjustment software, and then confirm if the result is OK.
(3) Select “Tebure Revise Adj.” of the adjustment software, and then confirm if the result is OK.
(4) Mount the AS Slider Unit (863) to the camera.
1-5. METHOD FOR REPLACING THE AS SLIDER B ASSY
Removal Procedure
(1) Remove the spring.
Spring
(2) Remove the solder on the enamel wires at two places.
Solder
Solder
(3) Remove the flexible board from the AS Slider B Assy.
Flexible Board
(4) Remove two screws.
(5) Remove the AS Unit Holder Ball.
AS Unit Holder Ball
(6) Remove two Ball Bearings.
Ball Bearing
Ball Bearing
(7) Remove two Cap SPs (for Pitch and Yaw).
Cap SP
(8) Remove two Caps (for Pitch and Yaw).
Cap
(9) Remove the AS Slider A Assy.
It can be done easily if A is removed beforehand.
AS Slider A Assy
A
(10) Remove the AS Slider B Assy.
It can be done easily if B is removed beforehand.
AS Slider B Assy
B
(11) Remove three Ball Bearings.
Ball Bearing
DSLR-A560/A560L/A560Y/A580/A580L/A580Y/A580J_L2
1-3E
1-6. METHOD FOR REPLACING THE AS HOLDER ACTUATOR ASSY
Assembly Procedure
Note: Make sure to perform the assembly procedures after assembling the AS Holder Actuator Assy.
The assembly procedure is the reverse of the removal procedure.
Apply grease to the portions indicated below.
* Refer to “SUBSIDIARY MATERIALS” on page 2-2 for the part number of grease.
* After applying grease, attach the Ball Bearings.
Ball Bearing
G
G-15
AS Slider B Assy
G
G-15 and G G-116
* After applying grease, attach the Ball Bearings.
Ball Bearing
G
G-15
Ball Bearing
G
G-15
Removal Procedure
Note: Make sure to perform the removal procedures after removing the
AS Slider B Assy.
(1) Remove the solder on the enamel wires at two places.
Solder
(2) Remove the flexible board from the hook on the AS Holder Actuator
Assy.
Hook
(3) Remove four screws to remove the AS Holder Actuator Assy.
AS Holder Actuator Assy
Assembly Procedure
Note: Make sure to perform the assembly procedures before assembling
the AS Slider B Assy.
The assembly procedure is the reverse of the removal procedure.
Apply grease to the portions indicated below.
* Refer to “SUBSIDIARY MATERIALS” on page 2-2 for the part
number of grease.
AS Holder Actuator Assy
G
G-15 and G G-116
DSLR-A560/A560L/A560Y/A580/A580L/A580Y/A580J_L2
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the given numerical order.
IDENTIFYING PARTS
View Position
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original one.
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay
should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Due to standardization, replacements in the parts list may be different from the parts specified
in the diagrams or the components used on the set.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
When indicating parts by reference number,
please include the board name.
ACCESSORIES
Link
ACCESSORIES
ASSEMBLY
DISCHARGING OF THE CHARGING CAPACITOR
• Abbreviation
AUS : Australian model
CH : Chinese model
KR : Korea model
Bottom View
Top View
Back View
Right View
Left View
Front View
qj�
Mirror Box Section
[Disassembly]
[Exploded View]
• Sub Unit-1
• Sub Unit-2
qh�
Mirror Box Section (Penta Unit)
[Disassembly]
[Exploded View]
qf�
Battery Holder Section
[Disassembly]
[Exploded View]
• ST-218 Board
• GYJ-003 Flexible Board
• STG-001 Flexible Board
qa�
Anti Shake Unit Section
[Disassembly]
[Exploded View]
• Imager Section
• IM Imager Unit
• ISL-001 Flexible Board
• ISP-001 Flexible Board
• Anti Shake Unit Section
qs�
Shutter Unit (AFE-3032)
qd�
BD RT Holder Assy
• SMR-001 Flexible Board
8�
AM-025 Board
• MM-084 Board
9�
BD Main Frame
7�
Top Cover Section
[Disassembly]
[Exploded View]
2�
Rear Cover Section
[Disassembly]
[Exploded View]
• Rear Cover Section
• LCD Section
• PD-390 Board
• LCD-014 Flexible Board
• SHD-001 Flexible Board
1�
CV Side Cover L Assy
0�
BD Bottom Frame
4�
CV Front Cover Assy (865)
qg�
ALX-8650 (AF Module)
3�
CV Grip Cover Assy
6�
BD Eye Piece Assy
• EYE-010 Flexible Board
DSLR-A560/A560L/A560Y/A580/A580L/A580Y/A580J_L2
2-2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked or
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, do not pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, do not press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
The charging capacitor is charged up to the maximum 330 V
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
DISCHARGING OF THE CHARGING CAPACITOR
Cut and remove the part of gilt
which comes off at the point.
(Be careful that some
pieces of gilt may be left inside)
Wrap insulating tape.
B
: Adhesive bond
B-50 (J-6082-615-A)
G
: Grease
G-15 (J-6082-619-A)
G-85 (J-6082-626-A)
G-116 (J-6082-628-A)
SUBSIDIARY MATERIALS
Note:
Note:
High-voltage cautions
High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points with the short jig about
10 seconds.
To avoid the spark with the metal plate,wrap the short jig
with the insulation tape.
Short-circuit between the two points with the short jig about
10 seconds.
To avoid the spark with the metal plate,wrap the short jig
with the insulation tape.
R:1 kΩ/1 W
(Part code: 1-215-869-11)
Click on the first or last page to see other DSLR-A560 / DSLR-A560L / DSLR-A560Y / DSLR-A580 / DSLR-A580J / DSLR-A580L / DSLR-A580Y service manuals if exist.