DOWNLOAD Sony DSC-WX150 (serv.man2) Service Manual ↓ Size: 5.45 MB | Pages: 21 in PDF or view online for FREE

DSC-WX150_L2

1-11E

Note: As for the figure below, this model and the shape

of the main body are different.

Inspect it as follows when you exchange parts in the lens block.

Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
Appearance condition Scratches or stains must not be noticeable, except that the customer permits them.
Foreign matters on the lens The lens condition must not be worse than that when the camera was received from the customer.

Lens at TELE end

Lens at WIDE end

Upward

Downward

Horizontal

Full stroke check

1

2

3

4

5

Focus check
1

  Preparation

 

•  Camera installed re-assemble lens.

 

•  Chart (Printed PDF file at the same magnification) (Refer to <Reference>)

 • 

Tripod

 

•  Mirror (ex. CD)

 • 

Memory 

card

 • 

PC

2

  Shoot setting

 

(1)  Paste the chart.

 

•  Chart should be on the flat wall.

 

•  Illuminance level in the chart should be the same.

 

•  Make the tripod’s height and the center of the chart to the same height.

 

•  Enough space needed for shooting.

 

(2)  Set the camera.

 

•  Set [P] mode

 

•  Set [Maximum] size

 

•  Set ISO lowest level

 

•  Set Steady Shot [OFF]

 

•  Set Flash [OFF]

 

(3)  Set the camera on a tripod.

 

(4)  Adjust the position of the camera and the chart.

 

1. Set the zoom position of the camera at Wide end.

 

2. Attach the mirror onto the center of the chart.

 

    * The mirror should not tilt on the chart.

 

3. Set the camera to display the chart on LCD like in the following picture.

 

4. Adjust the camera position to the center of the chart.

 

    * Adjust the tripod height and the position (Lateral direction).

 

5. Adjust the camera angle to the frame of the chart with tripod.

 

    Remove the mirror.

3

  Shooting

      (1)  Set [Self-Timer]
      (2)  Shot
4

  Check the shot image.

      (1)  Check the shot image on PC.
 

100% Display (Display at the same magnification of its Pixel.)

 

Compare the image with the sample you set.

      No extreme focus blurring
      It should be distinguished the black and white by the sharpness between them.
      If it is in NG level, replace the lens unit.

<Reference>
•     How to Print the Chart
      Print “Forcus-Chart_A3.pdf” with printer.
      Print at the same magnification (It means 100 % size).
      Check the settings of printer to print in proper size.
•     Check of chart size.
      Make charts together and check if the size of charts is the following size.
      * The chart consists of 2 pcs.

DSC-WX150_L2

2-1

Follow the disassembly in the numerical order given.

SY

-327

3

 LCD Module

7

 Main Frame Assy

q;

 Lens Block Section

    • CD-841 Flexible Board

qs

 BTH Block Assy 

4

 Front Block Assy 

1

 Rear Block Assy 

8

 Upper Block Assy  

9

 ST-269 Flexible Board

qa

 SY-327 Board

6

 DC Cover

5

 Cover Block

     Assy

2

 Control Switch Block

(SW63150/SW63170)

NOTE:
•  -XX, -X mean standardized parts, so they may have some differences from the original 

one.

•  Items marked “*” are not stocked since they are seldom required for routine service. 

Some delay should be anticipated when ordering these items.

•  The mechanical parts with no reference number in the exploded views are not sup-

plied.

•  Due to standardization, replacements in the parts list may be different from the parts 

specified in the diagrams or the components used on the set.

• CAPACITORS:
 uF: 

μF

• COILS
 uH: 

μH

• RESISTORS
  All resistors are in ohms.
  METAL: metal-film resistor
  METAL OXIDE: Metal Oxide-film resistor
 F: 

nonflammable

• SEMICONDUCTORS
  In each case, u: μ, for example:
 uA...: 

μA... , uPA... , μPA... ,

 uPB... 

, 

μPB... , μPC... , μPC... ,

 uPD..., 

μPD...

The components identified by mark 0 

or dotted line with mark 0 are critical for 

safety.
Replace only with part number specified.
Les composants identifiés par une marque 
0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant 
le numéro spécifié.

Danger of explosion if battery is incorrectly
replaced.
Replace only with the same or equivalent
type.
Dispose of used batteries according to
the instructions.

•  Color Indication of Appearance Parts
 Example:
 

(SILVER) : Cabinet’s Color

 

(Silver)  : Parts Color

• Abbreviation
  CH 

: Chinese model

  CND  : Canadian model
  KR 

: Korea model

Right View

Left View

Front View

Bottom View

Top View

Back View

DSC-WX150_L2

2-2

•  Make sure that the flat cable and flexible board are not cracked 

of bent at the terminal.

  Do not insert the cable insufficiently nor crookedly.

•  When remove a connector, don’t pull at wire of connector. It is 

possible that a wire is snapped.

•  When installing a connector, don’t press down at wire of con-

nector. 

  It is possible that a wire is snapped.

•  Do not apply excessive load to the gilded flexible board.

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

The charging capacitor is charged up to the maximum 330 V 
potential.
There is a danger of electric shock by this high voltage when the 
capacitor is handled by hand.  The electric shock is caused by the 
charged voltage which is kept without discharging when the main 
power of the unit is simply turned off.  Therefore, the remaining 
voltage must be discharged as described below.

To preparing the short jig, a small clip is attached to each end of 
a resistor of 1 k

Ω /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to 
prevent electrical shock.

1 k

Ω/1 W

Wrap insulating tape.

1 k

Ω/1 W

Wrap insulating tape.

ST-269 Flexible
Board

C901

 

R:1 k

Ω/1 W

Note: High-voltage cautions

Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.

(Part code: 1-215-869-11)

ST-269 Flexible
Board

C901

DSC-WX150_L2

2-3

Ref. No. 

Part No. 

Description

Ref. No. 

Part No. 

Description

  1 

4-419-298-01 

COVER (180), DC (SILVER)

  1 

4-419-298-11 

COVER (180), DC (BLACK)

  1 

4-419-298-21 

COVER (180), DC (BLUE)

  1 

4-419-298-31 

COVER (180), DC (RED)

 2 

4-419-299-01  SHEET 

YP 

(180)

  3 

1-490-033-21 

SWITCH BLOCK, CONTROL (SW63150) (BLACK)

  3 

1-490-035-11 

SWITCH BLOCK, CONTROL (SW63170) (SILVER)

  3 

1-490-035-51 

SWITCH BLOCK, CONTROL (SW63170) (BLUE)

  3 

1-490-035-61 

SWITCH BLOCK, CONTROL (SW63170) (RED)

  4 

4-419-307-01 

CUSHION (180), LCD (Note 2)

  5 

4-419-304-01 

WINDOW (180), LCD (Note 2)

  6 

X-2583-899-1  CABINET REAR 180 SILVER ASSY (SILVER)

  6 

X-2583-900-1  CABINET REAR 180 BLACK ASSY (BLACK)

  6 

X-2583-901-1  CABINET REAR 180 BLUE ASSY (BLUE)

  6 

X-2583-902-1  CABINET REAR 180 RED ASSY (RED)

 LCD901 1-811-554-11  PANEL 

MODULE(PE2-BCM)

  #212 

4-270-114-01 

SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)

  #244 

4-412-769-21 

SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)

1.  Remove to numerical order (

1

 

to

 

3

) in the left figure.

1

When assembling,
adjust the position.

3

2

1 

1 

2

1

#212

#244

#212

#244

#212

#244

Bottom View

Left View

Right View

The screw pointed       is different according to the cabinet's color.

For the combination of cabinet's color and screw, please refer to Table 2-1.

#212 (Silver)

SILVER

#244 (Black)

BLACK/BLUE/RED

Table 2-1

Note 2:  Refer to “Assembly-4:  Attaching Method of LCD 

Cushion (180), LCD Window (180)”.

1.4

3.0

#212: M1.4 X 3.0 

(Silver)
4-270-114-01

#244: M1.4 X 3.0 

(Black)
4-412-769-21

3.0

1.4