View Sony DSC-WX150 (serv.man2) Service Manual online
Replace only with part number
Ne les remplacer que par une piè-
ce portant le numéro spécifié.
1-2. ADDITION OF DESTINATION DATA FILE
1-3. PRECAUTION ON REPLACING THE LENS
1-4. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
1-5. HOW TO WRITE DATA TO INTERNAL MEMORY
1-8. ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD
1-9. DC MOTOR WORM ASSY REPLACING METHOD
1-10. THREE TUBE LUBRICATING BLOCK ASSY AND GROUP 1 FRAME REPLACING
(35 mm film equivalent))
Exposure control: Automatic exposure,
(Disparity Image)) compliant
• Manufactured under license from
media, “Memory Stick Micro” media,
SD cards, microSD memory cards
Micro USB connector:
Exif Print: Compatible
PRINT Image Matching III:
Approx. 48 g (1.7 oz)
Approx. 43 g (1.5 oz)
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 0.9 A
change without notice.
CH : Chinese model
CND : Canadian model
KR : Korea model
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
leaded solder and leaded solder will cause detachment phenomenon.
customer and recommend their replacement.
6. Flexible Circuit Board Repairing
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.
• Angular Velocity Sensor Sensitivity adjustment
• AWB standard data input & check, Color reproduction check
SY-327 board for service is supplied with written the PlayMemories Home.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity adj”.
In that case, download a new Destination Data file from the TISS homepage according to the following procedure.
the replacement lens for service.
Start the Adjust Manual and read the QR code using a QR code reader.
The read data is used for adjustment after replacement.
Select “Lens data carry” on the ADJUST tab of the Adjust Manual, and
click the LOAD button to load the file.
Note 2:When replacing the SY-327 board, execute formatting and initialize the internal memory after replacement.
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the
Images cannot be copied individually.
The original images in the internal memory are retained even after copying. To delete the contents
of the internal memory, remove the memory card after copying, then format the internal memory
([Format] in [Internal Memory Tool]).
The data will be copied to the recording folder that is currently being used, with a number one
higher than the largest data number in that folder.
When you use a memory card with this camera for the first time, it is recommended to format the card
using the camera for stable performance of the memory card before shooting. Note that formatting
permanently erases all data on the memory card, and is unrecoverable. Save precious data on a
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
To change settings is enabled with using the writing enabler tool (Write Enable Tool) on the Adjust Manual is activating from the Adjust Station.
6) Write the data read out into the PC to the internal memory of the camera.
7) Disconnect the PC from the camera, and turn off the camera.