Sony DSC-W90 (serv.man15) Service Manual ▷ View online
6-32
DSC-W90_ADJ
3.
Adjustment Time Out
Symptom
Adjustment does not finish within the specified
time.
time.
Cause
•
Adjustment conditions are wrong.
•
Data error exists in the camera.
Remedy
•
Check that the conditions such as a subject
are correct.
are correct.
•
Reset the camera.
4.
Adjustment NG
Symptom
The adjusted data does not become the speci-
fied value.
fied value.
Cause
•
Adjustment conditions are wrong.
•
Data error exists in the camera.
Remedy
•
Check that the conditions such as a subject
are correct.
are correct.
•
Reset the camera.
This part indicates
the adjustment
item in which
an error occurred.
the adjustment
item in which
an error occurred.
This part indicates
the adjustment
item in which
an error occurred.
the adjustment
item in which
an error occurred.
1-8. ERRO
In the case of an error during the execution of adjustment, the
Automatic Adjustment Program interrupts the processing at that
point, and displays an error message, and then terminates the pro-
gram execution there.
Automatic Adjustment Program interrupts the processing at that
point, and displays an error message, and then terminates the pro-
gram execution there.
1-9-1.
Error Message
When an error message is displayed, perform the remedy given
below, and then retry adjustment. If the error message is displayed
though the remedy was performed, the circuits will be faulty.
below, and then retry adjustment. If the error message is displayed
though the remedy was performed, the circuits will be faulty.
1.
Connect Error, Adjust Control Error
Symptom
USB communication with the set is abnormal.
Cause
•
USB cable is not inserted tightly.
•
Power supply is not installed correctly.
•
Communication with SeusEX is abnormal.
Remedy
•
Disconnect the USB cable once, and then re-
connect it tightly and check that the set is in
“USB Mode”.
connect it tightly and check that the set is in
“USB Mode”.
•
Install the power supply correctly.
•
Start the SeusEX and click the
[Connect]
to
check that the connection state is established.
2.
RESET the CAMERA and Try Again
Symptom
The camera is not ready for adjustment.
Cause
Data error exists in the camera.
Remedy
Reset the camera.
6-33
DSC-W90_ADJ
5.
Data Save Error
Symptom
data cannot be saved normally. (The data set-
ting during adjustment cannot be cancelled)
ting during adjustment cannot be cancelled)
Cause
•
Data writing to the flash memory failed.
•
Connection is faulty.
•
Power supply is not installed correctly.
Remedy
•
On the SeusEX Operation screen, [Set] the
data to the pages and addresses displayed in
the message, and [Save] them. (Cancel manu-
ally the data setting during adjustment.)
data to the pages and addresses displayed in
the message, and [Save] them. (Cancel manu-
ally the data setting during adjustment.)
•
Check the connection.
•
Install the power supply correctly.
1-8-2.
Precautions When an Error Occurred
The Automatic Adjustment Program sets the data for adjustment
before the adjustment starts. Accordingly, if the adjustment termi-
nates by an error, the data during the adjustment may be left in the
camera.
before the adjustment starts. Accordingly, if the adjustment termi-
nates by an error, the data during the adjustment may be left in the
camera.
Note 1:
With this data left in the camera, the camera will not op-
erate normally.
erate normally.
In this case, the [Release Data Setting] button is displayed in “red”
on the screen as shown figures below. Click the
[Release Data Setting] button to cancel the data setting. When the
data setting is cancelled, the button color becomes “white”.
on the screen as shown figures below. Click the
[Release Data Setting] button to cancel the data setting. When the
data setting is cancelled, the button color becomes “white”.
Note 2:
When “Data Save Error” occurred, the [Release Data
Setting] button is displayed in “white”.
To cancel the data setting, perform it on the SeusEX Op-
eration screen. How to cancel the data setting is displayed
in the error message.
Setting] button is displayed in “white”.
To cancel the data setting, perform it on the SeusEX Op-
eration screen. How to cancel the data setting is displayed
in the error message.
Video System Adjustment screen
Camera System Adjustment screen
How to cancel the data setting during
adjustment is display here.
adjustment is display here.
6-34
DSC-W90_ADJ
6-2. MODO DE SERVIÇO
2-1. APLICAÇÃO PARA AJUSTE (SeusEX)
The adjustment software (SeusEX) can change operational coeffi-
cients of signal processing, EVR data, etc. same as the adjustment
remote commander. The SeusEX performs two-way communica-
tion between PC and camcorder using the USB terminal. The two-
way communication result data can be written in the nonvolatile
memory.
cients of signal processing, EVR data, etc. same as the adjustment
remote commander. The SeusEX performs two-way communica-
tion between PC and camcorder using the USB terminal. The two-
way communication result data can be written in the nonvolatile
memory.
1.
Connection
1) Connect the HASP key to the USB terminal of the PC.
2) Connect the PC and camcorder with the USB cable.
3) Start the SeusEX on the PC.
4) Click [Connect] on the SeusEX screen. If the connection is
2) Connect the PC and camcorder with the USB cable.
3) Start the SeusEX on the PC.
4) Click [Connect] on the SeusEX screen. If the connection is
normal, the SeusEX screen will be as shown in Fig. 6-2-1,
indicating the “connected” state.
indicating the “connected” state.
Note:
The SeusEX will go in “disconnect” state, if the
camcorder is turned off (for instance, by resetting the
set). In such a case, click [Connect] on the SeusEX
screen to restore the “connected” state.
camcorder is turned off (for instance, by resetting the
set). In such a case, click [Connect] on the SeusEX
screen to restore the “connected” state.
Fig. 6-2-1
2.
Operation
• Block change
To change the block, click [Block] on the SeusEX screen and
enter the block to be changed. The block is displayed in hexa-
decimal notation.
enter the block to be changed. The block is displayed in hexa-
decimal notation.
• Page change
To change the page, click [Page] on the SeusEX screen and enter
the page to be changed. The page is displayed in hexadecimal
notation.
the page to be changed. The page is displayed in hexadecimal
notation.
• Address change
To change the address, click [Address] on the SeusEX screen
and enter the address to be changed. The address is displayed in
hexadecimal notation.
and enter the address to be changed. The address is displayed in
hexadecimal notation.
• Data change
To change the data, click [Set] on the SeusEX screen and enter
the data. The data is displayed in hexadecimal notation.
This operation does not write the data to the nonvolatile memory.
the data. The data is displayed in hexadecimal notation.
This operation does not write the data to the nonvolatile memory.
• Data writing
To write the data to the EEPROM, click [Write] on the SeusEX
screen and enter the data value to be written.
To write the data to the flash memory, change the data value
using the [Set] on the SeusEX screen and then click [Save] to
save the data.
screen and enter the data value to be written.
To write the data to the flash memory, change the data value
using the [Set] on the SeusEX screen and then click [Save] to
save the data.
• Data reading
The data displayed on the SeusEX screen are the data values at
the time when the pages and addresses were set, and they are not
updated automatically. To check the data change, click [Read]
on the SeusEX screen and update the displayed data.
the time when the pages and addresses were set, and they are not
updated automatically. To check the data change, click [Read]
on the SeusEX screen and update the displayed data.
6-35
DSC-W90_ADJ
2.
Switch Check
Click the [Switch Check] button on the SERVICE MODE screen,
and the “SWITCH CHECK” screen will appear.
and the “SWITCH CHECK” screen will appear.
Using method:
Click the [Start] button, and the switch check will start.
During execution of switch check, the pressed switch is displayed
in orange. Also, once the switch was pressed, its name characters
change to blue in color.
Click the [Start] button, and the switch check will start.
During execution of switch check, the pressed switch is displayed
in orange. Also, once the switch was pressed, its name characters
change to blue in color.
2-2. MODO DE SERVIÇO
1.
Function of Each Button on Service Mode Screen
Click the [SERVICE MODE] button on the Main Menu screen, and
the “SERVICE MODE” screen in Fig. 6-2-2 will appear.
the “SERVICE MODE” screen in Fig. 6-2-2 will appear.
Fig. 6-2-2
1
[To Menu] button
The Main Menu screen comes back.
The Main Menu screen comes back.
2
[Switch Check] button
“SWITCH CHECK” screen appears.
“SWITCH CHECK” screen appears.
3
[LED Check] button
“LED CHECK” screen appears.
“LED CHECK” screen appears.
4
[Record Data] button
“RECORD DATA” screen appears.
“RECORD DATA” screen appears.
5
[Aging] button
“AGING” screen appears.
“AGING” screen appears.
1
4
5
2
3
Click on the first or last page to see other DSC-W90 (serv.man15) service manuals if exist.