Sony DSC-W80 / DSC-W80HDPR / DSC-W85 (serv.man2) Service Manual ▷ View online
2-9
DSC-W80/W85_L2
5
Peel the adhesive sheet (upper) that secures the main flexible board.
6
Disengage the main flexible board from the hook of the ring assembly, and then slide the main flexible board
to remove.
to remove.
7
Peel the adhesive sheet (lower) that secures the main flexible board.
* The FOCUS motor must remain soldered.
* The FOCUS motor must remain soldered.
8
Remove four screws that secure the rear assembly.
9
Remove the rear assembly, disengaging the bosses at four places.
* Take care not to get stuck with the vibration-proof flexible board.
* Take care not to get stuck with the vibration-proof flexible board.
q;
Unhook the Z leaf spring to remove.
qa
Remove the main flexible board from the ring assembly, and remove the rear assembly and the nuruto gear.
6
Main flexible board
7
Adhesive sheet (lower)
Hook
Ring assembly
Ring assembly
qa
Nuruto gear
Ring assembly
Vibration-proof flexible board
Boss
Solder of FOCUS motor
5
Adhesive sheet (upper)
8
Four screws
9
Rear
assembly
assembly
Hook
qa
Main flexible
board
board
q;
Z leaf
spring
spring
qa
Rear assembly
Boss
2-10
DSC-W80/W85_L2
•
HOW TO REMOVE THE ZOOM GEAR BLOCK
1
Unsolder the zoom motor.
2
Remove the FG leaf spring.
3
Remove the main flexible board from the zoom gear block.
4
Remove the zoom gear block.
2-4-2. HOW TO INSTALL THE ZOOM GEAR BLOCK
•
HOW TO INSTALL THE ZOOM GEAR BLOCK
1
Solder the main flexible board to the zoom gear block.
2
Install the main flexible board to the zoom gear block.
3
Attach the FG leaf spring.
1
Solder
2
FG leaf spring
Hook
Hook
4
Zoom gear block
3
Main flexible board
3
Main flexible board
Rear assembly
1
Solder
3
FG leaf spring
Zoom gear block
2
Main flexible board
2
Main flexible board
Rear assembly
2-11
DSC-W80/W85_L2
4
Apply the lubricant (SRX-4339) to the nuruto gear, and insert it into the ring assembly.
* Rotate the gear in the ring assembly in the arrow direction until the end of the gear is not engaged
* Rotate the gear in the ring assembly in the arrow direction until the end of the gear is not engaged
with a concave portion of the ring assembly (because a convex portion of the rear assembly enters
the convex portion).
the convex portion).
5
Install the zoom gear block on the rear assembly.
6
Engaging four bosses, install the rear assembly on the ring assembly.
* The vibration-proof flexible board must be engaged with the hook of the rear assembly.
* The vibration-proof flexible board must be engaged with the hook of the rear assembly.
7
Tighten four screws in the order of A to D.
*
*
Tightening torque = 0.049
±
0.01N
•
m (0.5
±
0.1kgf
•
cm)
8
Check that the projection of the nuruto shaft that protrudes from the rear assembly is within the
specified value given below.
*
specified value given below.
*
Specified value: 0.005 – 0.395mm
4
Nuruto gear
Ring assembly
Ring assembly
7
Four screws
Hook
6
Vibration-proof
flexible board
flexible board
Nuruto shaft
Nuruto shaft
5
Zoom gear block
6
Rear assembly
Convex portion
Gear
Boss
Boss
0.005 – 0.395mm
8
D
A
B
C
2-12
DSC-W80/W85_L2
9
Secure and connect the main flexible board.
q;
Secure and connect the vibration-proof flexible board and the shutter flexible board respectively.
Main flexible board
Main flexible board
Adhesive sheet (lower)
Hook
Hook
Ring assembly
Adhesive sheet (upper)
Z leaf
spring
spring
Hook
Hook
Shutter flexible board
Connector
Connector
Bousin flexible board
Adhesive
sheet
sheet
Vibration-proof flexible board
Click on the first or last page to see other DSC-W80 / DSC-W80HDPR / DSC-W85 (serv.man2) service manuals if exist.