Sony DSC-W620 Service Manual ▷ View online
DSC-W620
3-9
Assembly-5: Connector Locking Method.
To lock the connector, gradually press the Lock plate in an order
indicated below to avoid damaging the Lock plate.
indicated below to avoid damaging the Lock plate.
Lock Plate
Main Board
CCD Block Assy
Flexible Board
Flexible Board
CCD Block Assy
3
1
2
Shutter assy
CAM BARREL
To this cam
groove
groove
The phase of
FPC portion
FPC portion
The phase of the
2nd shiny surface
2nd shiny surface
The phase of the
1st shiny surface
1st shiny surface
Assembled
(The inner-block_4)
(The inner-block_4)
1. Align the shutter assy with the CAM BARREL as shown in the figure.
2. Assemble the inner-block_4 just by dropping the shutter assy into the CAM BARREL linearly in the arrow direction.
3-5. Assembling
DSC-W620
3-10
The inner-block_4
The phase of
FPC portion
FPC portion
The front barrel part
To this cam groove
To this cam groove
The phase of this space:
Here is the space for the lever of
Lens barrier.
Only this area is concave inward.
Lens barrier.
Only this area is concave inward.
Aligned
3. Align the inner-block_4 with the front barrel part as shown in the figure.
Convex part
of the inner-
block_4
of the inner-
block_4
Convex part
of the front
barrel part
of the front
barrel part
Two grooves of
2ND OUTER
BARREL
2ND OUTER
BARREL
Either three kinds of
phases are available.
phases are available.
Entrance for the convex parts
4. Confirm the two types of groove of 2ND OUTER BARREL, the convex of the inner-block_4, and the convex of the
front barrel part as shown in the figure.
5. Align the 2ND OUTER BARREL with the inner-block_4 & the front barrel part as shown in the figure.
DSC-W620
3-11
<1>
Put the 2ND OUTER BARREL
linearly until it stops.
Put the 2ND OUTER BARREL
linearly until it stops.
<2>
Turn the pins of the inner-block_4 a little in
the arrow direction to move it to the
position shown left.
Turn the pins of the inner-block_4 a little in
the arrow direction to move it to the
position shown left.
Moved
Before move
<3>
Push the pins of the inner-block_4 a little
in the arrow direction.
At this stage, the convex parts of the
inner-block_4 have been entered in the
groove of 2ND OUTER BARREL.
Push the pins of the inner-block_4 a little
in the arrow direction.
At this stage, the convex parts of the
inner-block_4 have been entered in the
groove of 2ND OUTER BARREL.
2ND OUTER
BARREL
BARREL
6. Assemble the 2ND OUTER BARREL with the inner-block_4 & the front barrel part as shown in the figure.
Assembled
(The inner-block_3)
(The inner-block_3)
Before turning three pins
After turning
The inner-block_4
2ND OUTER BARREL
7. Turn the three pins approx. 120 degree in the arrow direction while holding the 2ND OUTER BARREL.
DSC-W620
3-12
Linear guide ring
The inner-block_3
To this groove
The phase of
FPC portion
FPC portion
The phase of
two cut portions
two cut portions
Keep holding three pins.
Keep holding the shutter assy.
Assembled
(The inner-block_2)
(The inner-block_2)
8. Align the linear guide ring with the inner-block_3 as shown in the figure.
9. Assemble the linear guide ring with the inner-block_3 as the inner-block_2 as shown in the figure.
If the linear guide ring does not fit completely, retry while keeping the three pins and the shutter assy in the arrow
directions.
directions.
DRIVE BARREL
LINEAR CAM BARREL
Assembled DRIVE BARREL
& LINEAR CAM BARREL
& LINEAR CAM BARREL
The only thin projection
should be located around
this phase.
should be located around
this phase.
The phase of drive gear portion
The inner-block_1
The inner-block_2
United DRIVE BARREL
& LINEAR CAM BARREL
& LINEAR CAM BARREL
< Reference >
At this point, if the DRIVE BARREL & LINEAR CAM BARREL have been separated, assemble them as
shown in the figure.
shown in the figure.
10. Assemble the inner-block_2 with the united DRIVE BARREL & LINEAR CAM BARREL as the inner-block_1 as
shown in the figure.
Click on the first or last page to see other DSC-W620 service manuals if exist.