Sony DSC-W620 Service Manual ▷ View online
DSC-W620
3-5
1. Disconnect the soldered connection.
2. Remove the four screws.
3. Remove the four screws.
3-2. Replacing MOTOR UNIT
Rear retainer
Rear lens spring
2ND FOCUS GEAR
PI part
4. Remove the rear retainer with careful attention so as not to let the rear lens spring fly away.
5. Remove the 2ND FOCUS GEAR.
6. Remove the PI part with a tool such as flat-blade screwdriver.
DSC-W620
3-6
Part for Zoom drive
FPC affixed with
Double-faced-tape
Double-faced-tape
FPC affixed with
Double-faced-
tape
Double-faced-
tape
PI part
7. Remove the part for Zoom drive. Remove the part of the FPC affixed with Double-faced-tape.
8. Remove the part of the FPC affixed with Double-faced-tape.
9. Remove the PI part with a tool such as flat-blade screwdriver.
Part of Focus motor
10. Remove the part of Focus motor.
11. MOTOR UNIT can be removed.
12. After the MOTOR UNIT has been replaced with a new one, return the process from 11. to 1. according to the process
flow.
DSC-W620
3-7
To Tele, apply a positive supply voltage (+) of
DC2.5 V here.
DC2.5 V here.
Outside
Inside
1. Set the lens to Tele position.
2. Heat the COSMETIC RING up with a heater such as hair dryer.
Pour a solvent such as ethyl alcohol.
Pick the COSMETIC RING with a thin tool such as cutter knife.
Pick the COSMETIC RING with a thin tool such as cutter knife.
3-3. Replacing BARRIER ASSY
Outside
Inside
3. Unlock the four hooks with a thin tool.
4. BARRIER ASSY can be removed.
DSC-W620
3-8
Assembly-1: Installation Cautions of the Main Board.
After fixing the main board with 3 screws,
solder the main board and strobe board.
Strobe Board
Solder Position
Screw
Screw
Screw
Main Board
Assembly-2: Installation Cautions of the Strobe Board.
Solder Position
Battery Terminals
Screw
Screw
Screw
Strobe Board
After fixing the strobe board with 3 screws,
solder the strobe board and battery terminals.
(When fixing the strobe board with screws,
confirm that 3 pieces of battery terminal are
inserted in the holes at soldered portions)
Assembly-3: Installation Cautions of the Speaker (1.0cm).
Route the Speaker Harness as shown below.
Speaker Harness
Ribs
Assembly-4: How to distinguish the side of Optical Filter Block
facing to Lens Device.
• IR cut coating surface
The red coating is reflected.
• The other surface
The red coating is
not reflected.
The red coating is
not reflected.
• Side view
The red belt
is seen.
The red belt
is seen.
Lens Device side
Lens Device side
Hold it with tweezers or the like.
Optical Filter Block
[IR Cut Coated Side]
[The Other Side]
The one side of the Optical Filter Block has treated with IR cut coating.
Mount the Optical Filter Block facing the IR cut coated side to the lens
device. Distinguish the IR cut coated side from the other by applying the
fluorescent light to the Optical Filter Block in the dark place (cut off the
outside light).
Mount the Optical Filter Block facing the IR cut coated side to the lens
device. Distinguish the IR cut coated side from the other by applying the
fluorescent light to the Optical Filter Block in the dark place (cut off the
outside light).
Outside
Inside
Lever
Space for the lever of Lens barrier
5. After the BARRIER ASSY has been replaced with a new one, return the process from 4. to 1. according
to the process flow.
Note: Align the lever with the dedicated space as shown in the figure
3-4. Assembly
Click on the first or last page to see other DSC-W620 service manuals if exist.