Sony DSC-W550 (serv.man2) Service Manual ▷ View online
DSC-W550_L2
2-2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at
the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that
a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE CHARGING CAPACITOR (C901)
The charging capacitor is charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the capacitor
is handled by hand. The electric shock is caused by the charged voltage
which is kept without discharging when the main power of the unit is
simply turned off. Therefore, the remaining voltage must be discharged
as described below.
There is a danger of electric shock by this high voltage when the capacitor
is handled by hand. The electric shock is caused by the charged voltage
which is kept without discharging when the main power of the unit is
simply turned off. Therefore, the remaining voltage must be discharged
as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a resistor
of 1 k
of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent elec-
trical shock.
trical shock.
1 k
Ω/1 W
Wrap insulating tape.
1 k
Ω/1 W
Wrap insulating tape.
MA-473 Flexible
Board
Board
R:1 k
Ω/1 W
C901
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.
Short-circuit between two points with
the short jig about 10 seconds.
(Part code: 1-215-869-11)
– ENGLISH –
– JAPANESE –
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け,折れ等がな
いことを確認する。
また,コネクタへの接続は,差し込み不足や斜め差しにならないように
注意する。
• コネクタを取り外す時に,線材部(極細)を持って引っ張ると断線する恐
れがありますので,絶対に線材部(極細)を持って引っ張らないでくださ
い。
い。
• 線材部(極細)を押さえながらコネクタを差し込むと,線材部(極細)が断
線する恐れがありますので,絶対に線材部(極細)には負担をかけないで
ください。
ください。
• 金メッキされているフレキシブル基板には,強い負担をかけないでくだ
さい。
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
ストロボ用充電コンデンサ(C901)の放電
ストロボ用充電コンデンサは最大315Vの電圧で充電されていま
す。
この高電圧で充電されたコンデンサに手を触れた場合,電気ショッ
クを受けます。この高電圧には単にセットの電源を切っただけで
は放電されず,残留しています。このため,下記の方法で残留電
圧を放電してください。
す。
この高電圧で充電されたコンデンサに手を触れた場合,電気ショッ
クを受けます。この高電圧には単にセットの電源を切っただけで
は放電されず,残留しています。このため,下記の方法で残留電
圧を放電してください。
ショート治具の準備
ショート治具は1kΩ/1W抵抗(1-215-869-11)の両端に小型のク
リップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けないように
してください。
リップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けないように
してください。
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
MA-473 Flexible
Board
Board
R:1 k
Ω/1 W
ࠦࡦ࠺ࡦࠨߩ㔚
ࡈ࠶ࠪࡘ࡙࠾࠶࠻ߩ㔚Ḯࠦࡦ࠺ࡦࠨ
ߩ┵ሶ㑆ࠍ࡚ࠪ࠻ᴦౕߢ⚂⑽㑆
ធ⛯ߔࠆޕ
ࡈ࠶ࠪࡘ࡙࠾࠶࠻ߩ㔚Ḯࠦࡦ࠺ࡦࠨ
ߩ┵ሶ㑆ࠍ࡚ࠪ࠻ᴦౕߢ⚂⑽㑆
ធ⛯ߔࠆޕ
C901
ㇱຠࠦ࠼㧦
1-215-869-11
Ver. 1.1 2011.08
DSC-W550_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. REAR SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
4-264-757-01
SIDE CAB R (710)
2
4-264-754-01
CUSHION (710), LCD (Note 2)
3
4-171-152-02
WINDOW (620), LCD (Note 2)
4
4-168-192-01
SHEET (680), LCD INSULATING
5
4-264-762-01
SHEET2 (700), LCD INSULATING
6
A-1800-423-A SW-576 BOARD, COMPLETE
7
1-880-210-11
FPC-020 FLEXIBLE BOARD
8
X-2560-719-1 CABINET (REAR) ASSY (710C) (SILVER) (Note 3)
8
X-2560-720-1 CABINET (REAR) ASSY (710D) (BLACK) (Note 3)
8
X-2582-200-1 CABINET (REAR) ASSY (710E) (PINK) (Note 3)
8
X-2582-201-1 CABINET (REAR) ASSY (710F) (GREEN) (Note 3)
8
X-2582-202-1 CABINET (REAR) ASSY (710G) (BLUE) (Note 3)
9
4-264-758-01
MC LID (710) (SILVER)
9
4-264-758-11
MC LID (710) (BLACK)
9
4-264-758-21 MC LID (710) (PINK)
9
4-264-758-31 MC LID (710) (GREEN)
9
4-264-758-41 MC LID (710) (BLUE)
LCD901 1-802-983-11
LCD MODULE (LMS300GF07)
#209
4-264-751-01
SCREW (M1.4), NEW TRU-STAR (Note 1)
#210
4-264-765-01
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
1. Remove to numerical order (
1
to
6
) in the left figure.
DISASSEMBLY
1
#209/#210 X 5
Screw
1
8
(Note 3)
6
LCD901
3
(Note 2)
2
(Note 2)
4
Front/Top Section
(See page 2-4)
(See page 2-4)
4
7
5
6
2
9
3
1
5
(Claw)
5
#209
#210
(Note 1)
#210
(Note 1)
#209
#210
(Note 1)
#210
(Note 1)
#209
#210
(Note 1)
#210
(Note 1)
1
(Claw)
Bottom View
Left View
Right View
#209
#210
#209
#210
#209
#210
Note
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
The screw pointed
is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
#209 (Silver)
SILVER, PINK, GREEN
#210 (Black)
BLACK, BLUE
Cabinet's Color
Table 2-1
Note 2: Refer to “Assembly-5: Attaching Method of LCD
Cushion (710), LCD Window (620)”.
Note 3: Refer to “Assembly-4: Precaution During of Cabinet
(Rear) Assy Installation.”.
4
DISCHARGING OF THE CHARGING CAPACITOR
#209: M1.4 X 3.5
(Silver)
4-264-751-01
4-264-751-01
1.4
3.5
#210: M1.4 X 3.5
(Black)
4-264-765-01
4-264-765-01
1.4
3.5
Ver. 1.2 2012.05
Note 2: “Assembly-5: Attaching Method of LCD Cushion
(710), LCD Window (620)”を参照してください。
Note 3: “Assembly-4: Precaution During of Cabinet (Rear)
Assy Installation.”を参照してください。
DSC-W550_L2
2-4
2-1-2. FRONT/TOP SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
X-2560-710-1 CABINET (FRONT) ASSY (710C) (SILVER)
51
X-2560-711-1
CABINET (FRONT) ASSY (710D) (BLACK)
51
X-2582-203-1 CABINET (FRONT) ASSY (710E) (PINK)
51
X-2582-204-1 CABINET (FRONT) ASSY (710F) (GREEN)
51
X-2582-205-1 CABINET (FRONT) ASSY (710G) (BLUE)
52
4-264-736-01
BT LID (710) (SILVER) (Note 2)
52
4-264-736-11
BT LID (710) (BLACK) (Note 2)
52
4-264-736-21 BT LID (710) (PINK) (Note2)
52
4-264-736-31 BT LID (710) (GREEN) (Note2)
52
4-264-736-41 BT LID (710) (BLUE) (Note2)
53
4-264-883-01
TAPE SP (700) (Note 3)
54
4-264-746-01 HOLDER
(700),
CAPACITOR
55
4-264-763-01
SHEET, MA (700)
56
1-882-981-11
MA-473 FLEXIBLE BOARD (Note 3)
57
3-080-272-01 TAPE
(A)
58
4-264-743-01
LIGHT GUIDE (700)
59
1-880-206-11
FPC-016 FLEXIBLE BOARD
60
1-487-574-11
FLASH UNIT
61
A-1800-422-A ST-255 BOARD, COMPLETE
62
4-264-752-01
ST SHEET 1 (700)
63
4-264-753-01
ST SHEET 2 (700)
64
X-2560-713-1 CABINET (UPPER) ASSY (710C)
65
4-264-755-01
FRAME (710), MAIN
66
4-264-759-01
INSULATING SHEET (710), SY
BT900
1-756-710-12
LITHIUM RECHARGEABLE BATTERY (MS614)
C901
1-116-439-21
CAP, ELECT 56uF 315V
MIC901 1-542-721-41
MICROPHONE BLOCK (Note 3)
SP901
1-858-297-11
LOUDSPEAKER (1.0CM) (Note 3)
#209
4-264-751-01
SCREW (M1.4), NEW TRU-STAR (Note 1)
#210
4-264-765-01
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
1. Remove to numerical order (
1
to
7
) in the left figure.
DISASSEMBLY
1
#209/#210 X 1
Screw
C901
BT900
6
54
: BT900 (LITHIUM RECHARGEABLE BATTERY)
Board on the mount position.
(See page 6-20 of Level3)
(See page 6-20 of Level3)
Main Section
(See page 2-5)
(See page 2-5)
2
51
SP901
(Note 3)
(Note 3)
7
56
(Note 3)
MIC901
(Note 3)
(Note 3)
57
55
59
60
4
-3
63
4
-2
4
-1
62
3
64
4
61
5
58
3
(Claws)
53
(Note 3)
2
(Claw)
4
(Claw)
#209
(Note 1)
(Note 1)
#209
#210
(Note 1)
1
65
66
52
(Note 2)
Note
Note 3: Refer to “Assembly-3: Precaution During of
MA-473 Flexible Board Installation.”.
4
(
4
-1
) Tape (A) → (
4
-2
) ST Sheet 1 (700) → (
4
-3
) ST Sheet 2 (700)
3
#209 X 1
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
The screw pointed
is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
#209 (Silver)
SILVER, PINK, GREEN
#210 (Black)
BLACK, BLUE
Cabinet's Color
Table 2-1
Note 2:
REMOVING METHODE OF THE BT LID
Removing and Installing of the BT lid, after remove
the cabinet (rear) assy and the cabinet (front) assy.
the cabinet (rear) assy and the cabinet (front) assy.
Incline
the BT lid
the BT lid
Remove
the BT lid
the BT lid
Bottom View
#209
#210
Back View
#209
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
#209: M1.4 X 3.5
(Silver)
4-264-751-01
4-264-751-01
1.4
3.5
#210: M1.4 X 3.5
(Black)
4-264-765-01
4-264-765-01
1.4
3.5
Note 3: “Assembly-3: Precaution During of MA-473
Flexible Board Installation.”を参照してくださ
い。
い。
注意
電池の交換は、正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は、取扱指示に従って処分してください。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は、取扱指示に従って処分してください。
Ver. 1.2 2012.05
DSC-W550_L2
2-5
2-1-3. MAIN SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
X-2560-728-1 BTH
ASSY
(710C)
*
102
3-289-764-01 GASKET (280)
103
4-266-038-01 GASKET
(700)
104
4-264-756-01
SIDE CAB L (710) (SILVER)
104
4-264-756-11
SIDE CAB L (710) (BLACK, BLUE)
104
4-264-756-21 SIDE CAB L (710) (PINK)
104
4-264-756-31 SIDE CAB L (710) (GREEN)
105
A-1805-814-A SY-284 BOARD, COMPLETE (SERVICE)
106
4-168-198-01
INSULATING SHEET (670) (Note 2)
*BT901 1-780-835-11
TERMINAL BOARD BATTERY (Note 3)
*BT902 1-780-835-11
TERMINAL BOARD BATTERY (Note 3)
*BT903 1-780-835-11
TERMINAL BOARD BATTERY (Note 3)
1. Remove to numerical order (
1
to
4
) in the left figure.
2. The meaning of the sign in left figure is as follows. Be careful when it removes.
◇-X
: Solder
DISASSEMBLY
BT902
(Note 3) BT903
(Note 3)
BT901
(Note 3)
1
Lens Block Section
(See page 2-6)
(Note 1)
(Note 1)
106
(Note 2)
4
101
2
104
102
102
102
3
105
103
-3
Note
Note 1:
Hold the Lens Block at the
center of both sides.
center of both sides.
Do not hold the following part.
Hold here.
Lens Flexible Board
PRECAUTIONS WHEN HOLDING THE LENS BLOCK
Note 2: Refer to “Assembly-2: Insulating Sheet (670)
Putting Position”.
Note 2: “Assembly-2: Insulating Sheet (670) Putting
Position”を参照してください。
Note 3: Refer to “Assembly-1: Installation Method of
Battery Terminal Board”.
Note 3: “Assembly-1: Installation Method of Battery
Terminal Board”を参照してください。
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2012.05
Click on the first or last page to see other DSC-W550 (serv.man2) service manuals if exist.