Sony DSC-W380 (serv.man2) Service Manual ▷ View online
DSC-W380_L2
2-2
MA-461フレキシブル基板のストロボ用充電コンデンサ
(C901)は最大315Vの電圧で充電されています。
この高電圧で充電されたコンデンサに手を触れた場合,
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
ショート治具の準備
ショート治具は1kΩ/1W抵抗(1-215-869-11)の両端に
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
The charging capacitor (C901) of the MA-461 Flexible flexible
board is charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
board is charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
– ENGLISH –
– JAPANESE –
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け,
折れ等がないことを確認する。
また,コネクタへの接続は,差し込み不足や斜め差しになら
ないように注意する。
• コネクタを取り外す時に,線材部(極細)を持って引っ張ると
断線する恐れがありますので,絶対に線材部(極細)を持って
引っ張らないでください。
引っ張らないでください。
• 線材部(極細)を押さえながらコネクタを差し込むと,線材部
(極細)が断線する恐れがありますので,絶対に線材部(極細)
には負担をかけないでください。
• 金メッキされているフレキシブル基板には,強い負担をかけ
ないでください。
DISCHARGING OF THE CHARGING CAPACITOR (C901)
ストロボ用充電コンデンサ(C901)の放電
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
Short-circuit between two points
with the short jig about 10 seconds.
R:1 k
Ω/1 W
(Part code: 1-215-869-11)
C901
MA-461 Flexible
Board
Board
C901
R:1 k
Ω/1 W
(部品コード:1-215-869-11)
コンデンサの放電
高電圧の警告
Note:
フラッシュユニットの電源コンデンサ
の端子間をショート治具で約10秒間
接続する。
の端子間をショート治具で約10秒間
接続する。
MA-461 Flexible
Board
Board
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
先端の剥がれたメッキ部はカットして
除去してください。
(メッキ破片がコネクタ内に残っている
場合もあるので注意してください)
除去してください。
(メッキ破片がコネクタ内に残っている
場合もあるので注意してください)
Wrap insulating tape.
絶縁テープで巻く
DSC-W380_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
4-168-190-01
CABINET (L (670)), SIDE (SILVER)
1
4-168-190-11
CABINET (L (670)), SIDE (BLACK)
1
4-168-190-21
CABINET (L (670)), SIDE (RED)
1
4-168-190-31
CABINET (L (670)), SIDE (GOLD)
2
1-837-002-11
CABLE, FLEXIBLE FLAT (FFC-216)
3
A-1731-538-A SW-561 BOARD, COMPLETE
4
4-167-835-01
DIAL (670), MODE
5
4-167-836-01
PLATE (670), MODE
6
4-167-839-01
SHEET (670), BRACKET ADHESIVE
* 7
4-167-837-01
BRACKET (670), STRAP
8
X-2541-692-1 CABINET (REAR) ASSY (670C) (EXCEPT GOLD)
8
X-2541-693-1 CABINET (REAR) ASSY (670F) (GOLD)
#65
2-635-591-01
SCREW (M1.4), NEW TRUSTAR P2 (Note)
#147
2-662-396-41
SCREW (M1.4), NEW, TRUSTAR, P2 (Note)
1. Remove to numerical order (
1
to
3
) in the left figure.
DISASSEMBLY
1
#65 / #147 X 7
Screw
#65: M1.4 X 3.5
(Silver)
2-635-591-01
2-635-591-01
3.5
1.4
2
#65
#147
(Note)
#147
(Note)
#65
#147
(Note)
#147
(Note)
#65
#147
(Note)
#147
(Note)
#65
#147
(Note)
#147
(Note)
LCD Section
(See page 2-4)
(See page 2-4)
4
5
6
7
3
1
2
3
1
8
2
(Boss)
#65
#147
#147
#65
#147
#147
#65
#147
#147
Right View
Left View
Bottom View
3.5
1.4
#147: M1.4 X 3.5
(Black)
2-662-396-41
2-662-396-41
Note
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
#65 (Silver)
SILVER/GOLD
#147 (Black)
BLACK/RED
Cabinet's Color
Table 2-1
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
For the combination of cabinet's color and screw, please refer to Table 2-1.
Note:
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2010.01
DSC-W380_L2
2-4
2-1-2. LCD SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
* 51
4-168-185-01
SCREW (670), TRIPOD
52
4-168-189-01
CABINET (R (670)), SIDE (SILVER)
52
4-168-189-11
CABINET (R (670)), SIDE (BLACK)
52
4-168-189-21
CABINET (R (670)), SIDE (RED)
52
4-168-189-31
CABINET (R (670)), SIDE (GOLD)
* 53
4-168-187-01
SHEET (670), INSULATING
54
1-880-292-11
MA-461 FLEXIBLE BOARD
55
4-168-197-01
SPACER (670), LCD
* 56
4-168-184-01
FRAME (670), MAIN
57
4-168-186-01
SHEET (670), LCD INSULATING
58
4-168-183-01
CUSHION (670), LCD (Note)
59
4-168-182-01
WINDOW (670), LCD (Note)
0 C901
1-116-440-11
CAP, ELECT 63uF 315V
LCD901 1-802-985-11
LCD MODULE (LQ027A3DD01)
53
57
4
55
Main Section
(See page 2-5)
(See page 2-5)
58
59
5
(Boss)
5
56
54
6
9
52
7
51
4
LCD901
(Note)
(Note)
8
C901
DISCHARGING OF THE CHARGING CAPACITOR
ストロボ用充電コンデンサの放電
1. Remove to numerical order (
4
to
9
) in the left figure.
DISASSEMBLY
6
Note
Note: Refer to “Assembly-4” when you install Attaching Method
of LCD cushion (670) and LCD window (670).
Note:
LCD CushionまたはLCD Windowを交換する際は、
Assembly-4 を参照してください。
4
LCD Insulating Sheet (670) (
4
)
DSC-W380_L2
2-5
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
X-2541-702-1 CABINET (FRONT) ASSY (670C) (SILVER)
101
X-2541-703-1 CABINET (FRONT) ASSY (670D) (BLACK)
101
X-2541-704-1 CABINET (FRONT) ASSY (670E) (RED)
101
X-2541-705-1 CABINET (FRONT) ASSY (670F) (GOLD)
* 102
3-093-800-01
GASKET (230)
103
4-168-195-01
LID (670), DC (SILVER)
103
4-168-195-11
LID (670), DC (BLACK)
103
4-168-195-21
LID (670), DC (RED)
103
4-168-195-31
LID (670), DC (GOLD)
104
X-2541-714-1 HOLDER ASSY (670C), BT (SILVER)
104
X-2541-715-1 HOLDER ASSY (670D), BT (BLACK)
104
X-2541-716-1 HOLDER ASSY (670E), BT (RED)
104
X-2541-717-1 HOLDER ASSY (670F), BT (GOLD)
105
4-168-198-01
INSULATING SHEET (670) (Note 2)
106
A-1751-400-A SY-262 BOARD, COMPLETE (SERVICE)
* 107
4-168-315-01
TAPE (N5)
0 * BT901 1-780-835-11
TERMINAL BOARD, BATTERY (Note 1)
0 * BT902 1-780-835-11
TERMINAL BOARD, BATTERY (Note 1)
0 * BT903 1-780-835-11
TERMINAL BOARD, BATTERY (Note 1)
#65
2-635-591-01
SCREW (M1.4), NEW TRUSTAR P2
2-1-3. MAIN SECTION
SY
-262
107
qs
102
103
105
#65
qs
Upper Cabinet Section
(See page 2-6)
q;
Lens Block Section
(See page 2-7)
-13
qf
104
qa
101
qd
106
BT903
(Note 1)
(Note 1)
BT902
(Note 1)
(Note 1)
BT901
(Note 1)
(Note 1)
(Note 2)
1. Remove to numerical order (
0
to
qf
) in the left figure.
2. The meaning of the sign in left figure is as follows. Be careful when it removes.
◇-X
: Solder
DISASSEMBLY
qs
#65 X 1 → Tape (N5) (
qs
)
Screw
#65: M1.4 X 3.5
(Silver)
2-635-591-01
2-635-591-01
3.5
1.4
#65
Back View
Note
Note 1: Refer to “Assembly-1” when you install battery terminal
board.
Note 1: バッテリ端子板を交換する際は、 Assembly-1 を参照
してください。
Note 2: Refer to "Assembly-2" when you install the Insulating Sheet
(670).
Note 2: Insulating Sheet (670)を取り付ける際は Assembly-2
を参照してください。
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2010.01
Click on the first or last page to see other DSC-W380 (serv.man2) service manuals if exist.