DOWNLOAD Sony DSC-W380 (serv.man2) Service Manual ↓ Size: 6.21 MB | Pages: 34 in PDF or view online for FREE

DSC-W380_L2

1-10

7

Match three ledges of the 1-group Frame Assy to three ditches of the Tube (A) Assy and install it.

8

Match two convex parts of the Tube (A) Assy to two convex parts of the Cam Tube.

9

Match three pins of the 1-group Frame Assy to three ditches of the Cam Tube.

0

Combine the Tube (A) Assy with the edge of the Cam Tube.

qa

Rotate the Cam Tube and the lens is retractile.

1-group 
Frame Assy

1-group 
Frame Assy

⎯ Eyepiece Side View ⎯

⎯ Objective Side View ⎯

⎯ Objective Side View ⎯

⎯ Side View ⎯

Tube (A) Assy

Tube (A) Assy

Pin of 1-group Frame Assy
(Make the other as much as
two places similar)

Tube (A) Assy

Tube (A) 
Assy

Tube (A) Assy

Tube (A) Assy

Tube (A) Assy

Ledges

Cam Tube Block

Cam Tube

Cam Tube

Cam Tube Block

Ditches

Barrier Lever

Convex Parts

Convex Parts

qs

Match seven convex parts of the Main Assy to seven ditches of the Fixed Tube and install it.

qd

Install the Naruto Gear on the Fixed Tube.

qf

Rotate the Naruto Gear and the lens is drawn out.

qg

Pass the Flexible Board through the hole of the Fixed Tube.

qh

Fix two claws of the Flexible Board into ribs of the Fixed Tube.

qj

Rotate the Naruto Gear and the lens is retractile.

Main Assy

Naruto Gear

Naruto Gear

⎯ Eyepiece Side View ⎯

Fixed Tube

Fixed Tube

Fixed Tube

Claws

Naruto Gear

Flexible Board

DSC-W380_L2

1-11

qk

Install the Rear Mirror Tube Assy on the Main Assy.
Note: Do not pinch the Flexible Board between the Rear Mirror Tube Assy and the Main Assy.

ql

Tighten up four screws in order of 

1 → 2 → 3 → 4.

* Tightening torque = 0.068 

± 0.01N • m (0.7 ± 0.1kgf • cm)

Rear Mirror Tube Assy

1

3

4

2

w;

Arrange the Flexible Board.

Main Assy

Rib

Rib

Boss

⎯ Left View ⎯

⎯ Bottom View ⎯

⎯ Top View ⎯

⎯ Right View ⎯

⎯ Rear View ⎯

Boss

Boss

Boss

Boss

Adhesive Sheet

Adhesive Sheet

Boss

Connect the Flexible Board 
from 2-group Frame Assy.

wa

With four bosses fitted in position, install Zoom Gear Block.

ws

Tighten one screw.
* Tightening torque = 0.068 

± 0.01N • m (0.7 ± 0.1kgf • cm)

Front Side

Rear Side

Screw

Zoom Gear Block

Bosses

Bosses

wd

Hook the Spring.

wg

Perform the Flange Back Adjustment after the assembling.

wf

Stick the Close Hole Tape.

Close Hole Tape

Spring

Tweezers

Inspect it as follows when you exchange parts in the lens block.
1

Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.

2

Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.

3

Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.

4

Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.

5

Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.

Lens at TELE end

Lens at WIDE end

Upward

Downward

Horizontal

Full stroke check

DSC-W380_L2

1-12E

Focus check
1

 Preparation

 

•  Camera installed re-assemble lens.

 

•  Chart (Printed PDF file at the same magnification) (Refer to <Reference>)

 • 

Tripod

 

•  Mirror (ex. CD)

 • 

Memory 

card

 • 

PC

2

 Shoot setting

(1)  Paste the chart.

•  Chart should be on the flat wall.
•  Illuminance level in the chart should be the same.
•  Make the tripod’s height and the center of the chart to the same height.
•  Enough space needed for shooting.

(2)  Set the camera.

•  Set [P] mode
•  Set [Maximum] size
•  Set ISO lowest level
•  Set Steady Shot [OFF]
•  Set Flash [OFF]

(3)  Set the camera on a tripod.
(4)  Adjust the position of the camera and the chart.

1. Set the zoom position of the camera at Wide end.
2. Attach the mirror onto the center of the chart.
  * The mirror should not tilt on the chart.
3. Set the camera to display the chart on LCD like in the following picture.
4. Adjust the camera position to the center of the chart.
  * Adjust the tripod height and the position (Lateral direction).
5. Adjust the camera angle to the frame of the chart with tripod.
  Remove the mirror.

3

 Shooting

(1) Set [Self-Timer]
(2) Shot

4

  Check the shot image.

(1)  Check the shot image on PC.
  100% Display (Display at the same magnification of its Pixel.)
  Compare the image with the sample you set.
No extreme focus blurring
It should be distinguished the black and white by the sharpness between them.
If it is in NG level, replace the lens unit.

<Reference>
•  How to Print the Chart
 

Print “Forcus-Chart_A3.pdf” with printer.

 

Print at the same magnification (It means 100 % size).

 

Check the settings of printer to print in proper size.

•  Check of chart size.
 

Make charts together and check if the size of charts is the following size.

 

* The chart consists of 2 pcs.

DSC-W380_L2

2-1

Follow the disassembly in the numerical order given.

• Abbreviation
 AR  : 

Argentine 

model

 AUS : 

Australian 

model

  BR 

: Brazilian model

  CH 

: Chinese model

  HK 

: Hong Kong model

  J 

: Japanese model

  KR 

: Korea model

NOTE:
•  -XX, -X mean standardized parts, so they may have some differences from the original 

one.

•  Items marked “*” are not stocked since they are seldom required for routine service. 

Some delay should be anticipated when ordering these items.

•  The mechanical parts with no reference number in the exploded views are not sup-

plied.

•  Due to standardization, replacements in the parts list may be different from the parts 

specified in the diagrams or the components used on the set.

• CAPACITORS:
 uF: 

μF

• COILS
 uH: 

μH

• RESISTORS
  All resistors are in ohms.
  METAL: metal-film resistor
  METAL OXIDE: Metal Oxide-film resistor
 F: 

nonflammable

• SEMICONDUCTORS
  In each case, u: 

μ, for example:

 uA...: 

μA... , uPA... , μPA... ,

 uPB... 

, 

μPB... , μPC... , μPC... ,

 uPD..., 

μPD...

【使用上の注意】 

• ここに記載されている部品は, 補修用部品であるため, 回路図及び
セットに付いている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金  被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。

•  Color Indication of Appearance Parts
 Example:
 

(SILVER) : Cabinet’s Color

 

(Silver)  : Parts Color

•  外装部品色表示
 

例：

 

(SILVER)  ：セットの色を表す。

 

(Silver)  ：部品の色を表す。

The components identified by mark 0 

or dotted line with mark 0 are critical for 

safety.
Replace only with part number specified.
Les composants identifiés par une marque 
0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant 
le numéro spécifié.

0印の部品，または0印付の点線で囲ま
れた部品は，安全性を維持するために，
重要な部品です。
従って交換時は，必ず指定の部品を使用
してください。

Right View

Left View

Front View

Bottom View

Top View

Back View

SY

-262

0 

Lens Block Section

 

 

• CD-773 Flexible Board

qs 

Upper Cabinet Section

 

 • 

ST-224 

Board