DOWNLOAD Sony DSC-W300 (serv.man2) Service Manual ↓ Size: 6.79 MB | Pages: 73 in PDF or view online for FREE

2-1

DSC-W300_L2

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.

• When installing a connector, don’t press down at wire of connector.

It is possible that a wire is snapped.

• Do not apply excessive load to the gilded flexible board.

Cut and remove the part of gilt 
which comes off at the point.
(Be careful or some 
pieces of gilt may be left inside) 

The charging capacitor (C901) of the AF-116 flexible board is
charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand.  The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off.  Therefore, the
remaining voltage must be discharged as described below.

To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k

Ω /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.

1 k

Ω

/1 W

Wrap insulating tape.

Note: High-voltage cautions 

Discharging the Capacitor
Short-circuit between the two points with the short jig about 10 seconds.
To avoid the spark with the metal plate,wrap the short jig with the insulation tape.

1

2

Charging
Capacitor (C901)

AF-116
Flexible Board

Resistor:1 k /1 W 
(Part code: 1-215-869-11)

Resistor:1 k /1 W 
(Part code: 1-215-869-11)

Main Frame Assy

2-2

DSC-W300_L2

Front Block

Cabinet (L)

Lens Block

Cabinet (G)
Block

Rear Cabinet
Block

LCD Block

AF-116 Flexible Board

Cabinet (Upper) Block

Battery Holder Section

 • Rear Cabinet Block
 • Cabinet (G) Block

 • LCD Block
 • Cabinet Bottom Assy
 • Cabinet (L)

 • Front Block

 • Lens Block
 • AF-116 Flexible Board

 • Cabinet (Upper) Block
 • SY-199 Board

Cabinet Bottom Block

2-3

DSC-W300_L2

Follow the disassembly in the numerical order given.

1

Rear Cabinet Block (

1

-1 to 

1

-4)

2

Cabinet (G) Block (

2

-1 to 

2

-2)

1

 Rear Cabinet

 

Block

2

 Cabinet (G) Block

LCD Section

2

-2 (Claw)

2

-1 (Claw)

1

-1

(#21)

1

-2

(#21)

1

-4

(Claw)

1

-3

(#21)

Note: High-voltage cautions 

Discharging the Capacitor
Short-circuit between the two points with the short jig about 10 seconds.
To avoid the spark with the metal plate,wrap the short jig with the insulation tape.

1

2

Charging
Capacitor (C901)

AF-116
Flexible Board

Resisitor:1 k /1 W 
(Part code: 1-215-869-11)

Resistor:1 k /1 W 
(Part code: 1-215-869-11)

Main Frame Assy

2-4

DSC-W300_L2

Follow the disassembly in the numerical order given.

1

LCD Block (

1

-1 to 

1

-4)

2

Cabinet Bottom Assy (

2

-1 to 

2

-4)

3

Cabinet (L) (

3

-1)

1

 LCD Block

2

-4 (#21)

2

-1 (#21)

2

-2

3

 Cabinet (L)

3

-1

1

-1

(Claw)

1

-2

(Claw)

1

-3

1

-4

Lens Section

2

 Cabinet

 

Bottom Assy

2

-3