DOWNLOAD Sony DSC-W1 / DSC-W12 (serv.man2) Service Manual ↓ Size: 4.51 MB | Pages: 47 in PDF or view online for FREE

2-5

Part Number

Part Name

Quantity

1

3-091-427-01

Ring (A), Ornamental

1

2

X-3954-476-1

Barrier Assy

1

3

3-086-156-31

Tapping screw (P2)

2

Torque driver
Soldering iron
Weight about 60g
Adhesive (Super X) (Note)

Use adhesive (Super X) or an equivalent article.
Don’t use what becomes white after drying like a quick-drying glue.

The Ornamental Ring A has adhered to the Barrier Assy strongly and accordingly, use a soldering iron to weaken the adhesive force.
Heat four circled portions with the soldering iron.
Heating temperature is about 300ºC.
Beware of a burn since the entire Ornamental Ring becomes hot.
*

As the adhesive force of Ornamental Ring A is considerably large, the forced peeling will damage the group-1 frame.

Insert the tip of tweezers, etc. into a notch of the group-1 frame and prize the ring.
*

Take extreme care so as not to damage the coated surface of the group-1 frame.

In case of difficult peeling, heat the ring again with the soldering iron.
If this re-heating failed, it may be advisable that the ring be peeled while heating the portions 1 

→ 2 → 3 → 4 in the under figure one

by one sequentially.

*

Discard the removed Ornamental Ring A.

1

2

3

1

Tip

3

4

2

2-6

1

Remove two screws.

*

Discard the removed screws.

2

Remove the Barrier Assy.

*

Discard the removed Barrier Assy.

*

After removing the Barrier Assy, if the “G1 Dust-Proof Ring” was removed, it must be returned to the home position.
In returning the ring, adjust the location of a projection to the lens direction.
This is an important part to prevent the dust and light from coming in.

*

After removing the Barrier Assy, take extreme care not to drop dust or foreign substances in the lens barrel.

1

Install new Barrier Assy by paying attention to the projection of the Barrier Assy in relation to the position shown in the under figure.

2

Tighten two screws.

*

Tightening torque = 0.5 kgf

1

1

2

Projection

2

2

1

2-7

Apply an adhesive to four recesses on the top surface of the Barrier Assy.
*

Do not apply too much adhesive. (Make quantity of adhesives into the quantity in which a groove hides.)

Meeting a “notch” of the Ornamental Ring A with a “projection” of the group-1 frame, push the Ornamental Ring A into the group-1 frame.
*

The projection of the spring for preventing static electricity must be tilted.

Put the 60g weight on the Ornamental Ring A so that the Ornamental Ring A does not float up until the adhesive hardens.

Be careful not to give a shock.

*

After the weight was put, no gap must be present in full circumference between Ornamental Ring A and group-1 frame.
A gap, if present, causes the crackle sound NG.

*

The weight must push in the Ornamental Ring A only.
If the weight is put on the mold part of the Barrier Assy, the Ornamental Ring A will float up.

Completion after 30 minutes.

Notch

Adhesive

Adhesive

Adhesive

Do not put the weight on a black mold part.

Not gap in full circumference.

Adhesive

Projection

2-8E

CD-507 flexible

US-011 flexible

SY-102
(including CH-146)

ST-101 flexible

ST-100

SW-422

CH-146
(included in SY-102)

JK-263

MS-205 flexible

MS-204

SP-045 flexible

CD-507 flexible

CCD IMAGER

CH-146

CCD SIGNAL PROCESS

(included in SY-102)
JK-263

JACK

MS-204

LCD DRIVE, MS CONNECTOR

MS-205 flexible

CONNECTOR

SP-045 flexible

SPEAKER

ST-100

FLASH DRIVE

ST-101 flexible

CHARGING CAPACITOR, FLASH UNIT

SY-102

CAMERA MODULE, CAMERA DSP, LENS DRIVE, 

(Including CH-146)

SH DSP, FRONT CONTROL, DC/DC CONVERTER

SW-422

AUDIO, CONTROL SWITCH

US-011 flexible

USB CONNECTOR