Sony DSC-W1 / DSC-W12 (serv.man2) Service Manual ▷ View online
1-1
SECTION 1
SERVICE NOTE
DSC-W1/W12
1-2. DISCHARGING OF THE ST-101
FLEXIBLE BOARD’S CHARGING
CAPACITORS (C102 AND C103)
CAPACITORS (C102 AND C103)
The charging capacitors (C102 and C103) of the ST-101 flexible
board are charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
board are charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a
resistor of 1 k
resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Discharging the Capacitor
Short-circuit between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
charged capacitor with the short jig about 10 seconds.
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
Capacitor
ST-101
ST kemikon sheet
1-2E
DSC-W1/W12
Display Code
1-4. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Self-diagnosis display
• C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
• E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
authorized Sony service facility.
1-3. NOTE IN LENS FRAME INSTALLATION
When tightening a screw, have both sides of the lens block assembly so as not for the load to depend.
C:32:ss
C:13:ss
Countermeasure
Turn the power off and on again.
Format the “Memory stick”.
Insert a new “Memory Stick”.
Cause
Trouble with hardware.
Unformatted memory stick is inserted.
Memory stick is broken.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
E:61:ss
E:91:ss
Checking of lens drive circuit.
When failed in the focus and zoom
initialization.
initialization.
Abnormality when flash is being
charged.
charged.
Checking of flash unit or replacement
of flash unit.
of flash unit.
—
Insert batteries correctly.
Batteries are not inserted correctly.
Batteries were installed or removed when
using the AC adaptor.
using the AC adaptor.
Turn the power off and on again.
E:92:ss
M1.4
×
4
Lens frame
Lens block assembly
DSC-W1/W12
2-1
2-2
2-1. FLOW CHART
The following flow chart shows the disassembly procedure.
SECTION 2
DISASSEMBLY
HELP
HELP
Note: When you exchange rings, be sure
to follow the procedure carried on
"2-3. Exchange Method of Barrier
Assy" (2-5 page).
"2-3. Exchange Method of Barrier
Assy" (2-5 page).
HELP
1
Open two connectors (CN201, 701)
2
Claw
x2
3
Lens block
4
CD-507: CN701
5
Lens block flexible: CN201
1
3
4
5
5
0
qa
7
8
2
6
9
1
2
4
5
6
8
9
7
3
0
1
Lock ace screw (M1.7)
x4
2
Claw
3
Rear cabinet
4
Side cover
5
Sheet (S)
6
Mic harness: CN102
7
Lock ace screw (M1.7)
x2
8
Front cabinet
1
BT terminal flexible: CN001
2
Tapping screw (M1.7)
x2
3
SY-102
4
MS-205 flexible: CN704
5
Lock ace screw (M1.7)
x2
6
Tapping screw (M1.7)
x2
7
Boss
8
DC and A/V jack
9
Claw
x2
0
MS-205
1
Lock ace screw
(M1.7)
(M1.7)
x2
2
SW-422
3
US-011 flexible: CN101
4
Lock ace screw
(M1.7)
(M1.7)
x1
5
Claw
x4
6
US-011
7
Claw
x2
8
Claw
x2
9
LCD block
0
LCD flexible: CN801
qa
Back light
flexible: CN802
flexible: CN802
1
Claw
x1
2
Claw
x1
3
Control SW block
4
Control SW block flexible: CN702
5
ST-101 flexible: CN601
6
Claw
x2
7
Strobo block
8
Tapping screw (M1.7)
x1
9
DC ground plate (B)
0
Claw
x2
qa
Claw
x1
qs
Bottom cabinet
3
qs
3
8
3
7
2
1
1
1
8
1
2
2
9
0
1
2
4
5
6
qa
0
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two
points with the short jig about 10
seconds.
Short-circuit between the two
points with the short jig about 10
seconds.
4
5
6
7
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
Capacitor
ST-101
ST kemikon sheet
4
5
9
1
Ornamental ring (A)
2
Tapping screw (M1.2)
x2
3
Barrier assy
1
2
3
DSC-W1/W12
2-3
2-4
2-2. SY-102 BOARD SERVICE POSITION
Lens block
LCD block
Stroboscope block
MS-205 flexible board
US-011 flexible board
SY-102 board
Control switch block
SW-422 board
Color monitor
AC power
adaptor
adaptor
AC IN
3
8
2
1
1
1
4
5
6
7
3
1
2
2
4
5
1
3
4
5
5
0
qa
7
8
2
6
9
1
2
4
5
6
8
9
7
3
9
qs
0
3
7
8
9
0
1
2
4
5
6
qa
0
Click on the first or last page to see other DSC-W1 / DSC-W12 (serv.man2) service manuals if exist.