Sony DSC-TX30 (serv.man2) Service Manual ▷ View online
DSC-TX30_L2
3-1
3. ASSEMBLY
Releasing Claws of the Cabinet (Front) Block Assy
(1) Insert the jig while lifting portion A in the direction of
arrow to release claw
arrow to release claw
1
.
(3) Insert the jig into claw
5
to release it.
(5) Open the cabinet (front) block assy in the direction
of arrow and release three claws (
of arrow and release three claws (
7
,
8
,
9
) on the
side panel to remove the cabinet (front) block assy.
(2) Insert the jig into claws
2
,
3
, and
4
to release claw
2
first, claw
3
, and then claw
4
sequentially.
Claw 1
Jig
Claw 2
Claw 3
Claw 4
Claw 7
Claw 8
Claw 9
Claw 5
Be sure to use a jig to release the claws of the cabinet (front)
block assy paying attention not to damage them.
block assy paying attention not to damage them.
Portion A
J-6082-771-A
CABINET REMOVER
CABINET REMOVER
(4) Insert the jig into claw
6
to release it.
Claw 6
Notes on Disconnecting and Connecting the TP Flexible Board
Prohibited Work
NG
NG
OK
OK
Recommended Work
Hold the ends of the TP flexible board with tweezers, bend it
up 90 degrees, and then insert it horizontally.
up 90 degrees, and then insert it horizontally.
Hold the reinforcing plate with tweezers and insert it in the
obliquely upward direction.
obliquely upward direction.
Push the ears of the flexible board reinforcing plate with
tweezers to disconnect it.
tweezers to disconnect it.
If the TP flexible board is not inserted
properly, push the ears of the
reinforcing plate with tweezers.
properly, push the ears of the
reinforcing plate with tweezers.
Hold the ends of the TP flexible board with tweezers and
pull it out horizontally.
pull it out horizontally.
TP flexible board
TP flexible board
SY-1009 Board
Connector
Reinforcing
plate
plate
TP flexible board
SY-1009 Board
Connector
Reinforcing
plate
plate
Tweezers
TP flexible board
SY-1009 Board
Connector
Reinforcing
plate
plate
Tweezers
TP flexible board
DSC-TX30_L2
3-2E
Assembly-1: Caution for Handling the Lens Device and other
parts of the Lens Block
Hold the Lens Block as shown figure.
CD-829 Board
Sensor
Motor
Lens
Very weak
Very weak
Very weak
Very weak
Motor
Very weak
Do not hold the following parts.
PRECAUTIONS WHEN HOLDING THE LENS BLOCK
• IR cut coating surface
The red coating is reflected.
The red coating is reflected.
• The other surface
The red coating is
not reflected.
The red coating is
not reflected.
• Side view
The red belt
is seen.
The red belt
is seen.
Lens Device side
Lens Device side
Hold it with tweezers or the like.
Optical Filter Block
[IR Cut Coated Side]
[The Other Side]
The one side of the Optical Filter Block has treated
How to distinguish the side of Optical Filter Block
facing to Lens Device.
facing to Lens Device.
with IR cut coating.
Mount the Optical Filter Block facing the IR cut
coated side to the lens device.
Distinguish the IR cut coated side from the other by
applying the fluorescent light to
the Optical Filter Block in the dark place
(cut off the outside light).
Mount the Optical Filter Block facing the IR cut
coated side to the lens device.
Distinguish the IR cut coated side from the other by
applying the fluorescent light to
the Optical Filter Block in the dark place
(cut off the outside light).
G12 Protection Sheet is supplied with the LSV-1501A
(SERVICE). This part is used to protect the LSV-1501A (SERVICE).
Remove this part when replacing the LSV-1501A (SERVICE).
And install the G10 Seal (1500).
(SERVICE). This part is used to protect the LSV-1501A (SERVICE).
Remove this part when replacing the LSV-1501A (SERVICE).
And install the G10 Seal (1500).
Install the G10 Seal (1500)
Remove the G12 Protection Seal
LSV-1501A (Service)
Assembly-2: Notes on Assembling the MIC Rubber
Install the MIC Rubber to the RL-1005 Flexible Board
as shown in the figure.
as shown in the figure.
RL-1005 Flexible
Board
Board
RL-1005 Flexible
Board
Board
MIC Rubbers
MIC Rubbers
Assembly-3: Notes on Assembling the RL-1005 Flexible Board
Boss
Bosses
RL-1005 Flexible Board
DSC-TX30_L2
4-1E
4. FRAME SCHEMATIC DIAGRAMS
Ver. 1.3 2014.11
IC001
(Not supplied)
IC211
(Not supplied)
IC051
(Not supplied)
1
2
50
49
CN001
CP1001
(Not supplied)
SY-1009 BOARD (SIDE A)
SY-1009 BOARD (SIDE B)
RL-1005
FLEXIBLE BOARD
FLEXIBLE BOARD
ST-1005
FLEXIBLE BOARD
FLEXIBLE BOARD
ML-2001
FLEXIBLE BOARD
FLEXIBLE BOARD
CD-829 FLEXIBLE BOARD
LENS BLOCK
MIC001
(MICROPHONE)
(L)
MIC002
(MICROPHONE)
(R)
S003
S005
1
2
41
40
38
39
1
60
61
2
3
4
5
6
7
8
9
10
11
1
21
20
13
14
15
16
17
18
12
19
22
23
25
24
18
19
5
16
17
10
12
11
1
2
49
50
1
17
16
18
CN801
CN802
CN803
TB704
TB705
CN701
CN702
CN715
CN719
23
22
21
20
18
2
19
1
SE401
PITCH/YAW
TB701
TB702
TB703
CN404
1
6
1
5
2
S001
1
1
16
7
8
1
6
+
S002
(TELE)
S004
(WIDE)
BATTERY TERMINAL
C901
CHARGING
CAPACITOR
FLASH UNIT
1
10
CN718
MULTI
TOUCH
PANEL
EL901
DISPLAY MODULE
3.3 INCH
WIDE
ORGANIC
EL PANEL
RECHARGEABLE
BATTERY
SP901
(SPEAKER)
+
BT900
(LITHIUM BATTERY)
ON/OFF
(MOVIE)
(SHUTTER)
DSC-TX30_L2
4-1E
4. FRAME SCHEMATIC DIAGRAMS
Ver. 1.3 2014.11
IC001
(Not supplied)
IC211
(Not supplied)
IC051
(Not supplied)
1
2
50
49
CN001
CP1001
(Not supplied)
SY-1009 BOARD (SIDE A)
SY-1009 BOARD (SIDE B)
RL-1005
FLEXIBLE BOARD
FLEXIBLE BOARD
ST-1005
FLEXIBLE BOARD
FLEXIBLE BOARD
ML-2001
FLEXIBLE BOARD
FLEXIBLE BOARD
CD-829 FLEXIBLE BOARD
LENS BLOCK
MIC001
(MICROPHONE)
(L)
MIC002
(MICROPHONE)
(R)
S003
S005
1
2
41
40
38
39
1
60
61
2
3
4
5
6
7
8
9
10
11
1
21
20
13
14
15
16
17
18
12
19
22
23
25
24
18
19
5
16
17
10
12
11
1
2
49
50
1
17
16
18
CN801
CN802
CN803
TB704
TB705
CN701
CN702
CN715
CN719
23
22
21
20
18
2
19
1
SE401
PITCH/YAW
TB701
TB702
TB703
CN404
1
6
1
5
2
S001
1
1
16
7
8
1
6
+
S002
(TELE)
S004
(WIDE)
BATTERY TERMINAL
C901
CHARGING
CAPACITOR
FLASH UNIT
1
10
CN718
MULTI
TOUCH
PANEL
EL901
DISPLAY MODULE
3.3 INCH
WIDE
ORGANIC
EL PANEL
RECHARGEABLE
BATTERY
SP901
(SPEAKER)
+
BT900
(LITHIUM BATTERY)
ON/OFF
(MOVIE)
(SHUTTER)