Sony DSC-TX1 (serv.man2) Service Manual ▷ View online
2-1
DSC-TX1_L2
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE ST-219 FLEXIBLE BOARD’S CHARGING CAPACITOR
(C901, C902)
(C901, C902)
The charging capacitor (C901, C902) of the ST-219 flexible board
is charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
is charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Capacitor
(C901)
(C901)
Capacitor
(C902)
(C902)
ST-219 Flexible
Board
Board
SY-231
Board
Board
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points
with the short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
Short-circuit between the two points
with the short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
2-2
DSC-TX1_L2
2-1. IDENTIFYING PARTS
2-2-1. OVERALL SECTION
• Front Cabinet Block
• Lens Block
• Lens Block
2-2-2. REAR SECTION
• SY-231 Board Block
• Cabinet (Rear) Assy
• LCD
• Cabinet (Rear) Assy
• LCD
2-2-3. ST SECTION
• ST-219 Flexible Board Block
• DISASSEMBLY FLOW -
Front Cabinet Block
SY-231 Board
Lens Block
• CD-763 Board
Main Frame Assy
• BT-054 Flexible Board
ST-219 Flexible
Board
Board
LCD
Cabinet (Rear) Assy
2-3
DSC-TX1_L2
HELP
HELP
EXPLODED VIEW
HARDWARE LIST
2-2. DISASSEMBLY
2-2-1. OVERALL SECTION
Follow the disassembly in the numerical order given.
1
Front Cabinet Block
(
1
-1 to
1
-6)
2
Lens Block
(
2
-1 to
2
-5)
This screw cannot be re-used.
Discard the screw removed once in servicing.
Instead, use a new screw.
Discard the screw removed once in servicing.
Instead, use a new screw.
Note 3:
Rear Section
(See Page 2-4)
2
Lens Block
1
Front Cabinet Block
1
-1
(Open)
1
-2
(#168/
#169)
(Note 3)
#169)
(Note 3)
1
-6E
1
-3
(#168/#169)
(Note 3)
(Note 3)
1
-4
(#168/
#169)
(Note 3)
#169)
(Note 3)
1
-5
(#168/
#169)
(Note 3)
#169)
(Note 3)
2
-2
2
-5E
2
-3
2
-1
(#169)
HELP01
HELP03
HELP02
HELP04
ST-219 Flexible
Board
Board
SY-231
Board
Board
Note 2: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points
with the short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
Short-circuit between the two points
with the short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
Note 1: Do not lose it while
disassembling.
Be sure to check it
assembled correctly.
Be sure to check it
assembled correctly.
2
-4
HELP06
HELP05
HELP07
2-4
DSC-TX1_L2
EXPLODED VIEW
HARDWARE LIST
2-2-2. REAR SECTION
Follow the disassembly in the numerical order given.
1
SY-231 Board Block
(
1
-1 to
1
-9)
2
Cabinet (Rear) Assy
(
2
-1 to
2
-2)
2
LCD
(
3
-1 to
3
-3)
This screw cannot be re-used.
Discard the screw removed once in servicing.
Instead, use a new screw.
Discard the screw removed once in servicing.
Instead, use a new screw.
Note :
HELP08
HELP10
1
SY-231 Board Block
1
-6 (#169)
1
-7
1
-1
HELP09
1
-5
1
-4
1
-9E
1
-2
1
-3
1
-8
(Claw)
2
Cabinet (Rear) Assy
2
-1
(#168/#169)
(Note)
(Note)
2
-2E
3
LCD
3
-2 (Claw)
3
-1
3
-3E
Click on the first or last page to see other DSC-TX1 (serv.man2) service manuals if exist.