Sony DSC-TX1 (serv.man2) Service Manual ▷ View online
1-1
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DSC-TX1_L2
1. SERVICE NOTE
1-1. PRECAUTION ON REPLACING THE SY-231 BOARD
RESTORE DATA
When you replace to the repairing board, get the acquire data from the former needed for the adjustment.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.
• USB Serial No.
• Angular Velocity Sensor sensitivity adj. (Dp/Dy/Fpy Data)
• Wide Limit adj.
• Angular Velocity Sensor sensitivity adj. (Dp/Dy/Fpy Data)
• Wide Limit adj.
Note:
When you cannot read data from the former replace the same time SY-231 board and lens.
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “Destination data write”.
Start the Adjust Manual in the Adjust Station and execute the “Destination data write”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB serial No. input”.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB serial No. input”.
Angular Velocity Sensor
When you replace to the reparing board, write down the sensitivity displayed on the angular velocity sensor (SE403).
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity adj”, input the date written down.
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity adj”, input the date written down.
Note:
The sensor sensitivity of SE403 of SY-231 board is written only repair parts.
1-2. PRECAUTION ON REPLACING THE LENS
About the Lens for Repair
When replacing the lens, write down the PITCH/YAW data, FN
data and wide limit data given on the lens for service.
Start the Adjust Manual in the Adjust Station and execute the “Wide
Limit adj.” and the “Angular velocity sensor sensitivity adj”, input the
data written down.
data and wide limit data given on the lens for service.
Start the Adjust Manual in the Adjust Station and execute the “Wide
Limit adj.” and the “Angular velocity sensor sensitivity adj”, input the
data written down.
About the Optical Filter Block
On attaching the Optical Filter Block, refer to “HELP07”.
Be sure to check there is no dust on the Optical Filter Block and attach it.
Be sure to check there is no dust on the Optical Filter Block and attach it.
Note:
The PITCH/YAW data, FN data and wide limit data of lens
are written only repair parts.
are written only repair parts.
SY-231 BOARD (SIDE B)
YYY: YAW Sensor Sensitivity
PPP: PITCH Sensor Sensitivity
YYY
PPP
SE403
L1/L2
FN
XX YY
XXYY
XX
P.PP/Y.YY
Wide Limit Data (2-byte data)
YAW data
PITCH/YAW Data
PITCH data
FN Data
FN data
1-2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DSC-TX1_L2
1-3. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)
Note 1:
When replacing the SY-231 board, erase the data in internal memory of the board before replacement.
Note 2:
When replacing the SY-231 board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Method for Formatting the Internal Memory or Memory Stick Duo
Copy
Copies all images in the internal memory to a “Memory Stick Duo” media.
1
Insert a “Memory Stick Duo” media with sufficient
free space into the camera.
free space into the camera.
2
t
(Settings)
t
("Memory Stick"
Tool)
t
[Copy]
t
[OK]
• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
• You cannot copy images individually.
• The original images in the internal memory are retained even after copying. To delete the contents of the
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick Duo” media after copying, then format the internal memory
([Format] in [Internal Memory Tool]).
([Format] in [Internal Memory Tool]).
• A new folder is created on the “Memory Stick Duo” media and all the data will be copied to it. You
cannot choose a specific folder and copy images to it.
Notes
Format
Formats the “Memory Stick Duo” media or the internal memory. A commercially available
“Memory Stick Duo” media is already formatted, and can be used immediately.
“Memory Stick Duo” media is already formatted, and can be used immediately.
1
t
(Settings)
t
("Memory Stick"
Tool) or
(Internal Memory To ol)
t
[Format]
t
[OK]
• Note that formatting permanently erases all data including even protected images.
Note
1-3
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DSC-TX1_L2
Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
To change settings is enabled with using the writing enabler tool (Write Enable Tool) on the Adjust manual is activating from the Adjust
station.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
To change settings is enabled with using the writing enabler tool (Write Enable Tool) on the Adjust manual is activating from the Adjust
station.
Data writing method
1)
Start the Adjust manual from the Adjust station.
2)
Click (Write Enable Tool) button.
3)
Click “Activate Write Enable Mode” button.
4)
Upon completion of the setting change, the following message will be displayed. Click OK button.
5)
Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).
6)
Write the data read out into the PC to the internal memory of the camera.
7)
Disconnect the PC from the camera, and turn off the camera.
Note:
By turning off the camera, the write enable setting is reset.
1-4. HOW TO WRITE DATA TO INTERNAL MEMORY
1-4
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DSC-TX1_L2
1-5. SELF-DIAGNOSIS FUNCTION
1-5-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to
do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
function starts working, and displays on the LCD screen what to
do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
1-5-2. Self-diagnosis Display
When problems occur while the unit is operating, the LCD screen
shows a 4-digit display consisting of an alphabet and numbers, which
blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”
of the problem.
shows a 4-digit display consisting of an alphabet and numbers, which
blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”
of the problem.
0 0
3 2
C
Repaired by:
Refer to “1-5-3. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
13 ....Format the “Memory Stick Duo”.
32 ....Turn on power again.
step to be taken.
E.g.
13 ....Format the “Memory Stick Duo”.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
E : Corrected by service
engineer
LCD screen
Click on the first or last page to see other DSC-TX1 (serv.man2) service manuals if exist.