Sony DSC-T77 (serv.man2) Service Manual ▷ View online
1-10E
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DSC-T77_L2
1-6. フラッシュエラー発生時の対処法
本機はフラッシュエラー(自己診断コードE:91:01)が発生した場合,高電圧による異常を防止するために自動的にフラッシュ
充電および発光禁止の設定になります。
フラッシュエラー発生後はエラーの解除を行う必要があります。エラーの解除はホーム画面から初期化操作を実行することによ
り行います。
フラッシュエラーの解除方法
お買い上げ時の設定に戻します。
[設定リセット]を実行しても、画像は削除されません。
[設定リセット]を実行しても、画像は削除されません。
1
(設定)
[本体設定]
[設定リセット]
[実行]
ご注意
設定リセット中は電源が切れないようにご注意ください。
設定リセット
2-1
DSC-T77_L2
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE ST-199 FLEXIBLE BOARD’S CHARGING CAPACITOR
(C901, C902)
(C901, C902)
The charging capacitor (C901, C902) of the ST-199 flexible board
is charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
is charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
SY
-207
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points
with the short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
Short-circuit between the two points
with the short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
ST-199 Flexible
Board
Board
Capacitors
C901
C902
2-2
DSC-T77_L2
2-1. IDENTIFYING PARTS
SY
-207
2-2-1. OVERALL SECTION
- Front Block
2-2-2. MAIN SECTION
- Lens Block
- SY-207 Board
- BT Lid Base
- SY-207 Board
- BT Lid Base
2-2-3. ST/REAR SECTION
- ST-199 Flexible Board
- LCD Block
- LCD Block
- DISASSEMBLY FLOW -
SY-207 Board
ST-199 Flexible Board
Front Block
Frame Assy
Control Switch Block
(RL61210)
(RL61210)
Loudspeaker
(1.0cm)
(1.0cm)
LCD Block
Lens Block
BT Lid Assy
Rear Cabinet Block
BT-044 Flexible Board
CD-743 Flexible Board
2-3
DSC-T77_L2
HELP
HELP
EXPLODED VIEW
HARDWARE LIST
1
Front Block
Main Section
(See Page 2-4)
1
-4
(Open)
1
-5
(#45)
1
-1
(#142/
#143)
#143)
1
-11
(#144)
1
-13
(Claw)
1
-12
1
-3
(#142/#143)
Front Block
Secure with tapes.
Remove two bosses
while holding the lens cover
on the center.
while holding the lens cover
on the center.
On assembling, attach the front block while holding the lens cover on the center.
1
-9
(Bosses)
1
-6
(Set the lens cover
to the center.)
to the center.)
1
-10
1
-7
(#142/#143)
Microphone
Holder
Holder
1
-8
(#142/#143)
HELP01
HELP03
HELP04
HELP02
1
-2
(#142/
#143)
#143)
How to diassemble the Front Block
Note: Microphone holder caution
There are some cases the microphone holder
is caught on the front block.
is caught on the front block.
When removing the Front block,
be careful not to damage the flexible board.
be careful not to damage the flexible board.
1
-14
HELP13
HELP14
2-2. DISASSEMBLY
2-2-1. OVERALL SECTION
Follow the disassembly in the numerical order given.
1
Front Block
(
1
-1 to
1
-14)
Click on the first or last page to see other DSC-T77 (serv.man2) service manuals if exist.