Sony DSC-HX60 / DSC-HX60V Service Manual ▷ View online
DSC-HX60/HX60V
4-7
(5) The Method of attachment of the BT-2010 Flexible Board
(1) Install the Terminal Battery Board to the BTH Assy.
Terminal Battery Board
BTH Assy
(2) Connect the BT-2010 Flexible Board to the Terminal Battery
Board.
BT-2010 Flexible Board
Terminal Battery Board
BTH Assy
(3) Set the Lithium Rechargeable Battery.
Lithium Rechargeable
Battery
Battery
(4) Set the claws and bosses.
Bosses
Claws
Claws
(6) Notes on Assembling the Upper Block
Route the speaker harnesses.
Cabinet (Front)
Speaker
Upper Block
DSC-HX60/HX60V
4-8
4-4. LENS BLOCK
4-4-1. Removal and Installation
(1) Ornamental Ring A or Barrier Assy Replacing Method
Removal
1. Turn on the power switch and extend the lens (TELE end).
2. Detach the battery.
3. Pour a solvent such as alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
4. Heat the Ornamental Ring A with a drier.
5. Turn the Ornamental Ring A clockwise and counterclockwise to detach it.
1. Turn on the power switch and extend the lens (TELE end).
2. Detach the battery.
3. Pour a solvent such as alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
4. Heat the Ornamental Ring A with a drier.
5. Turn the Ornamental Ring A clockwise and counterclockwise to detach it.
A
Ornamental Ring A
Solvent
Tweezers
Drier
6. Disengage the four claws and remove the Barrier Assy.
Claws
Barrier Assy
DSC-HX60/HX60V
4-9
Installation
1. Fit the four claws and attach the Barrier Assy.
1. Fit the four claws and attach the Barrier Assy.
Claws
Barrier Assy
Barrier Assy
2. Attach two Barrier Tapes so that the end of each tape comes to the dent.
Note: Attach Barrier Tapes carefully so that they do not wrinkle.
3. Attach the Ornamental Ring A and push it gently.
Ornamental Ring A
Barrier Tapes
Barrier Tapes
DSC-HX60/HX60V
4-10
(2) 2 Group Frame Block Assy Replacing Method
Removal
1. Release the claw to detach the Z Retainer.
2. Release the boss and the claw to detach the FG Retainer.
3. Release the claw to detach the FPC Retainer.
1. Release the claw to detach the Z Retainer.
2. Release the boss and the claw to detach the FG Retainer.
3. Release the claw to detach the FPC Retainer.
Claw
Claw
Boss
FG Retainer
FPC Retainer
Z Retainer
Claw
4. Unsolder the DC Motor Worm Assy at two locations shown below.
5. Disconnect the flexible board from the connector on the LF-2038 Flexible Board.
5. Disconnect the flexible board from the connector on the LF-2038 Flexible Board.
Solders
Connector
Disconnect the flexible board.
DC Motor Worm Assy
LF-2038 Flexible Board
6. Disconnect the three sensors on the LF-2038 Flexible Board.
7. Remove the five screws to detach the Rear Lens Assy.
7. Remove the five screws to detach the Rear Lens Assy.
Sensor
Screws
LF-2038 Flexible Board
Screws
Sensors
Rear Lens Assy
Click on the first or last page to see other DSC-HX60 / DSC-HX60V service manuals if exist.