Sony DSC-HX60 / DSC-HX60V Service Manual ▷ View online
DSC-HX60/HX60V
4-19
13. While matching the diamond mark on the Drive Gear Barrel Assy with the triangle mark on the Core Unit_2, insert the Core Unit_2 into
the Drive Gear Barrel Assy.
Core Unit_2
Drive Gear Barrel Assy
Triangle mark
Diamond mark
Match the diamond mark on the Drive Gear
Barrel Assy with the triangle mark on the
Core Unit_2.
Barrel Assy with the triangle mark on the
Core Unit_2.
14. While matching the semicircular cutout of the Core Unit_1 with the gear B mounting portion of the Fixed Barrel, insert the Core Unit_1
into the Fixed Barrel.
Core Unit_1
Semicircular
cutout
cutout
Gear B mounting
portion
portion
Fixed Barrel
Match the semicircular cutout of the Core Unit_1
with the gear B mounting portion of the
Fixed Barrel.
with the gear B mounting portion of the
Fixed Barrel.
15. Insert the Gear B.
Gear B
Gear B
DSC-HX60/HX60V
4-20
16. While matching the hole in the Fixed Barrel with the flexible board, install the 3 Group Frame Block Assy.
Hole for flexible board.
Flexible board
3 Group Frame Block Assy
Fixed Barrel
Core Unit_1
Core Unit_1
17. Turn the Gear B clockwise to set the lens unit in the TELE end state.
Note: Turn the Gear B to the maximum.
Gear B
18. Pass the flexible board through the hole in the Fixed Barrel and fix the flexible board to the groove and the boss.
Boss
Groove
Flexible board
Hole
Fixed Barrel
DSC-HX60/HX60V
4-21
19. Turn the Gear B counterclockwise to set the lens unit in the retracted state, and then remove the Gear B.
Gear B
Gear B
20. Fit the DC Motor Worm Assy with the boss and secure it with two screws.
21. Install Gear WH, Gear A, and then Gear B.
21. Install Gear WH, Gear A, and then Gear B.
Screws
Boss
DC Motor Worm Assy
Gear B
Gear A
Gear WH
DC Motor Worm Assy
22. Secure the Rear Lens Assy with five screws.
23. Connect the three sensors on the LF-2038 Flexible Board.
23. Connect the three sensors on the LF-2038 Flexible Board.
Sensor
Screws
Screws
Sensors
LF-2038 Flexible Board
Rear Lens Assy
DSC-HX60/HX60V
4-22
24. Fix the LF-2038 Flexible Board to the groove and the hole.
25. Connect the flexible board to the connector on the LF-2038 Flexible Board.
25. Connect the flexible board to the connector on the LF-2038 Flexible Board.
Connector
Groove
Hole
Flexible Board
LF-2038 Flexible Board
26. Solder the DC Motor Worm Assy at two locations shown below to secure the LF-2038 Flexible Board to the DC Motor Worm Assy.
Solders
DC Motor Worm Assy
27. Fix the FPC Retainer to the two projections and then to the claw.
28. Fix the FG Retainer to the boss and then to the claw.
29. Fix the Z Retainer to the two projections and then to the claw.
28. Fix the FG Retainer to the boss and then to the claw.
29. Fix the Z Retainer to the two projections and then to the claw.
Claw
Claw
Boss
Claw
FPC Retainer
Z Retainer
Projections
Projections
FG Retainer
30. Perform the Flange Back Adjustment after the assembling.
Click on the first or last page to see other DSC-HX60 / DSC-HX60V service manuals if exist.