DOWNLOAD Sony DSC-H5 (serv.man2) Service Manual ↓ Size: 2.83 MB | Pages: 50 in PDF or view online for FREE

1-1

DSC-H5_L2

Note : After repair, be sure to execute the “Initialize” of the setup screen.

Self-diagnosis display
• C: ss: ss

The contents which can be handled
by customer, are displayed.

• E: ss: ss

The contents which can be handled
by engineer, are displayed.

Display Code

  C:32:ss

  C:13:ss

Countermeasure

Turn the power off and on again.

Format the “Memory Stick” or internal
memory.

Insert a new “Memory Stick”.

Cause

Trouble with hardware.

“Memory Stick” or internal memory is
unformatted.

“Memory Stick” is broken.

Caution Display During Error

SYSTEM ERROR

FORMAT ERROR

MEMORY STICK ERROR

  E:61:ss

  E:91:ss

Checking of lens drive circuit.

Checking of flash unit or replacement
of flash unit. (Note)

Abnormality when flash is being
charged.

Batteries are pack is not inserted correctly.

Insert a batteries correctly.

Trouble with internal mamory.

Turn the power off and on again.

When failed in the focus zoom
initialization.

INTERNAL MEMORY ERROR

  E:92:ss

_

  E:62:ss

Inspect angular velocity sensor
peripheral circuits.

Steady shot function does not work well.

1-2

DSC-H5_L2

The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)

Note: 1 When replacing the SY-150 board, erase the data in internal memory of the board before replacement.
Note: 2 When replacing the SY-150 board or the IC202 on the SY-150 board, execute formatting and initialize the internal memory after 

replacement.

When “FLASH error”  (Self-diagnosis Code  E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the
flash is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.

Initializes the setting to the default setting.

1

Select [OK] with v on the control button, then press z.
The message “Initialize all settings Ready?” appears.

2

Select [OK] with v, then press z.
The settings are reset to the default setting.

Make sure that the power is not disconnected during resetting.

OK

See the following procedure.

Cancel

Cancels the resetting.

This item does not appear when a “Memory Stick Duo” is inserted in the camera.
The default settings are marked with 

.

Formats the internal memory.

• Note that formatting irrevocably erases all data in the internal memory, including even protected images.

1

Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be erased Ready?” appears.

2

Select [OK] with v, then press z.
The format is complete.

OK

See the following procedure.

Cancel

Cancels the formatting.

Copies all images in the internal memory to a “Memory Stick Duo”.

1

Insert a “Memory Stick Duo” having 32 MB or larger capacity.

2

Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be copied Ready?” appears.

3

Select [OK] with v, then press z.
Copying starts. 

• Use a fully charged Nickel-Metal Hydride battery or the AC Adaptor (not supplied). If you attempt to 

copy image files using a batteries with little remaining charge, the batteries may run out, causing copying 
to fail or possibly corrupting the data.

• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the 

internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in 

 (Internal Memory Tool).

• You cannot select a folder copied on a “Memory Stick Duo”.
• Even if you copy data, a 

 (Print order) mark is not copied.

OK

See the following procedure.

Cancel

Cancels the copying.

1-3E

DSC-H5_L2

• The Repair Board has already been adjusted. Re-initialization or EVR data copy from the set before repair is not

required.

• Perform “VIDEO OUT Default Data Check” and “Initial Language Data Check” mentioned below, and also the

adjustment items necessary after SY Board replacement.

When you replace to the repairing board, the written data of repairing board also might be changed to original setteing
because of broadcast system (NTSC/PAL).
When the data has changed because of board replaceing etc., check the default data of VIDEO OUT if destination code
is right. If not, rewrite to the right value.

Page

Address

Data

NTSC

PAL

4F

8D

00

01

Writing Method:
1) Select page: 00, address: 01, and set data: 01.
2) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL).
3) Select page: 40, address: 38, and set data: 00.
4) Click 

[Save]

 on the SEUS screen.

5) Select page: 80, address: 34, and check that the data is “00”.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.

If the SY-150 board was replaced, initial language setting may be changed. Accordingly, change the following data so
as to set same initial language as that of the set distributing in each region.

Initial language: Language displayed at the next starting if the setting of Setup menu was reset.

It is different from the language setting selectable with the menu.

Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8C, and set the Initial Language Data.
3) Select page: 40, address: 38, and set data: 00.
4) Click 

[Save]

 on the SEUS screen.

5) Select page: 80, address: 34, and check that the data is “00”.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.
8) Turn off the camera.
9) Turn on the camera. Execute “Initialize” of Setup screen.
10) Check the language displayed when the camera starts.

Page

Address

Data

Language

GP1

GP2

GP3

GP4

4F

8C

00

English

z

z

z

01

Japanese

z

04

Spanish

z

z

06

Portugal

08

Simplified Chinese

z

z

0B

Russian

z

0D

Korean

z

Note: GP1 is fixed to Japanese.

GP2 is fixed to English.
GP3 is either English, Spanish, or Russian.
GP4 is either English, Spanish, Portugal, Simplified Chinese, or Korean.

DSC-H5_L2