DOWNLOAD Sony DSC-H5 Service Manual ↓ Size: 2.07 MB | Pages: 27 in PDF or view online for FREE

Model
DSC-H5
Pages
27
Size
2.07 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL 3
File
dsc-h5.pdf
Date

Sony DSC-H5 Service Manual ▷ View online

SERVICE MANUAL
LEVEL
 
3
Revision History
Revision History
How to use
Acrobat Reader
How to use
Acrobat Reader
Sony EMCS Co.
2007F0800-1
  ©2007.06
Published by Kohda TEC
9-852-117-11
DSC-H5_L3
DSC-H5
Internal memory
ON BOARD
Internal memory
ON BOARD
Link
SERVICE NOTE
PRINTED WIRING BOARDS
SCHEMATIC DIAGRAMS
REPAIR PARTS LIST
Link
Ver. 1.3  2007. 06
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Note :
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Chinese Model
Brazilian Model
Hong Kong Model
Korea Model
Tourist Model
Japanese Model
DIGITAL STILL CAMERA
— 2 —
DSC-H5_L3
1.
Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
 : LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
°
C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
— 3 —
DSC-H5_L3
TABLE OF CONTENTS
1.
SERVICE NOTE
1-1.
METHOD FOR COPYING OR ERASING THE DATA IN
INTERNAL MEMORY ·················································· 1-1
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-2.
SCHEMATIC DIAGRAMS ·········································· 4-14
4-3.
PRINTED WIRING BOARDS ····································· 4-29
4-4.
MOUNTED PARTS LOCATION ································· 4-33
5.
REPAIR PARTS LIST
5-2.
ELECTRICAL PARTS LIST ········································ 5-12
1-1E
DSC-H5_L3
1. SERVICE NOTE
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note: 1 When replacing the SY-150 board, erase the data in internal memory of the board before replacement.
Note: 2 When replacing the SY-150 board or the IC202 on the SY-150 board, execute formatting and initialize the internal memory after 
replacement.
• PROCESS AFTER FIXING FLASH ERROR
When “FLASH error”  (Self-diagnosis Code  E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the
flash is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
Method for Initializing the Flash Error Code
Initializes the setting to the default setting.
1
Select [OK] with v on the control button, then press z.
The message “Initialize all settings Ready?” appears.
2
Select [OK] with v, then press z.
The settings are reset to the default setting.
Make sure that the power is not disconnected during resetting.
Initialize
OK
See the following procedure.
Cancel
Cancels the resetting.
Method for copying the data in internal memory
Method for formatting the internal memory
This item does not appear when a “Memory Stick Duo” is inserted in the camera.
The default settings are marked with 
.
Formats the internal memory.
• Note that formatting irrevocably erases all data in the internal memory, including even protected images.
1
Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be erased Ready?” appears.
2
Select [OK] with v, then press z.
The format is complete.
Format
OK
See the following procedure.
Cancel
Cancels the formatting.
Copies all images in the internal memory to a “Memory Stick Duo”.
1
Insert a “Memory Stick Duo” having 32 MB or larger capacity.
2
Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be copied Ready?” appears.
3
Select [OK] with v, then press z.
Copying starts. 
• Use a fully charged Nickel-Metal Hydride battery or the AC Adaptor (not supplied). If you attempt to 
copy image files using a batteries with little remaining charge, the batteries may run out, causing copying 
to fail or possibly corrupting the data.
• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the 
internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in 
 (Internal Memory Tool).
• You cannot select a folder copied on a “Memory Stick Duo”.
• Even if you copy data, a 
 (Print order) mark is not copied.
Copy
OK
See the following procedure.
Cancel
Cancels the copying.
Copying
102_COPY
1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
Page of 27
Display

Sony DSC-H5 Service Manual ▷ Download

  • DOWNLOAD Sony DSC-H5 Service Manual ↓ Size: 2.07 MB | Pages: 27 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony DSC-H5 in PDF for free, which will help you to disassemble, recover, fix and repair Sony DSC-H5 Digital Camera. Information contained in Sony DSC-H5 Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.