Sony DSC-H400 Service Manual ▷ View online
DSC-H400
4-13
Adjustment order
Screen display
4-3-9. Light/S.S Adjustment
The Light/S.S (Light Dead Pixel/Slow Shutter Dead Pixel)
Adjustment order is as follows.
Adjustment order is as follows.
Note:
Perform the Light/S.S Adjustment after those performed in 4-3-4 to 4-3-8.
Perform the Light/S.S Adjustment after those performed in 4-3-4 to 4-3-8.
The adjustment is finished normally.
OK
Fig.
4-3-25
The adjustment is complete.
Confirm the indication
on the screen.
Finished abnormally.
Finished normally.
In case of the indication other than that shown in
Fig. 4-3-25 appears on the screen, confirm the
adjusting environment and readjust.
Fig. 4-3-25 appears on the screen, confirm the
adjusting environment and readjust.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “Light S.S (BLACK)”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
*1 If the adjustment is disabled, refer to “4-1-6. Enabling the Adjustment” to enable the adjustment. (Page 4-3)
*2 It takes approximately 15 minutes or more on this adjustment.
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
*1 If the adjustment is disabled, refer to “4-1-6. Enabling the Adjustment” to enable the adjustment. (Page 4-3)
*2 It takes approximately 15 minutes or more on this adjustment.
In case of the adjustment
is finished normally, the
adjustment completion
indication appears on the
screen. (Fig. 4-3-25)
* The Self-timer lamp
lights up. (Fig. 4-3-24)
is finished normally, the
adjustment completion
indication appears on the
screen. (Fig. 4-3-25)
* The Self-timer lamp
lights up. (Fig. 4-3-24)
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “4-1-5. Setting the Adjustment Mode” (Page 4-3).
Press the flash unit pop-up button to raise the flash.
Cover camera lens (All black) (Fig. 4-3-23)
Cover camera lens (All black) (Fig. 4-3-23)
Restart the camera.
Fig. 4-3-24
Self-timer lamp
Camera
Equipment required: Cover camera lens
(All black)
Black cloth
Fig. 4-3-23
DSC-H400
4-14
4-3-10. Flash WB Adjustment
Preparing the Flash Adjustment Box
A dark room is required to provide an accurate flash adjustment. If it is not available, prepare the flash adjustment box as shown below.
1) Provide woody board A, B, C and D of 15 mm thickness. (Fig. 4-3-26)
2) Apply black mat paint to one side of woody board A, B and D.
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper side of woody board A, B, C and D are internal. (Fig. 4-3-27)
Woody board A
Woody board B
Woody board B
Woody board C
Woody board A
Woody board D
Front of the lens
L = 500 mm
L
Camera
Woody board A (2)
400 mm
Woody board B (2)
370 mm
Woody board C (1)
700 mm
513 mm
513 mm
700 mm
Woody board D (1)
370 mm
370 mm
700 mm
730 mm
100 mm
120 mm
Fig.
4-3-26
Fig. 4-3-27
DSC-H400
4-15
Adjustment order
Screen display
The adjustment is finished normally.
Succes
OK
Angle:1.7 deg.
Standard Angle:5.0 deg.
AF Luma:1144
Fig. 4-3-28
The adjustment is complete.
The adjustment is finished abnormally.
AFLam
NG
Angle:13.3 deg.
Standard Angle:5.0 deg.
AF Luma:4026
Fig. 4-3-29
Malfunction of Flash WB
adjustment
adjustment
The Flash WB Adjustment order is as follows.
Note:
Perform the Flash WB Adjustment after those performed in 4-3-4 to 4-3-9.
Perform the Flash WB Adjustment after those performed in 4-3-4 to 4-3-9.
Confirm the indication
on the screen.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 4-3-29)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 4-3-29)
In this case, confirm the adjusting environment
and readjust.
n
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “FLASH WB”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “4-1-6. Enabling the Adjustment” to enable the adjustment. (Page 4-3)
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “4-1-6. Enabling the Adjustment” to enable the adjustment. (Page 4-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 4-3-28)
Press the “ (Playback)” button to return to
adjustment menu.
the adjustment completion indication appears
on the screen. (Fig. 4-3-28)
Press the “ (Playback)” button to return to
adjustment menu.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “4-1-5. Setting the Adjustment Mode” (Page 4-3).
Place the camera in front of the Flash Adjustment Box. (Fig. 4-3-27)
Press the flash unit pop-up button to raise the flash.
Press the flash unit pop-up button to raise the flash.
Finished normally.
Finished abnormally.
DSC-H400
4-16
4-3-11. Lens Option
Lens Option Setting order is as follows.
1) Check that the camera is on the adjustment mode.
Note:
For the setting procedure of the adjustment mode, refer to “4-1-5. Setting the Adjustment Mode” (Page 4-3).
2) Press the Control button “ b ” “ B ” and “ v ” “ V ”to change selected item. Choose “Lens Option”,
press the “
(Playback)” button to choose item.
Note:
If the setting is disabled, refer to “4-1-6. Enabling the Adjustment” to enable the setting. (Page 4-3)
3) Press the Control button “ V ” to “Enable LDC” item after press the Control button “ B ” to set enable (00001).
Press the Control button “ V ” to “Enable LSC” item after press the Control button “ B ” to set enable (00001).
Press the Control button “ V ” to “Enable OIS” item after press the Control button “ z ” to set enable (00001).
Final Press the “
(Playback)” button to return to adjustment mode, then press the Control button “ z ”,
select “OK” and press the Control button “ z ” to start.
Note:
LDC : Lens Distortion Correction
LSC : Lens Shading Correction
OIS : Optical Image Stabilizer
4) Confirm the indication on the screen.
When the setting is finished, the setting completion indication appears on the screen. (Fig. 4-3-30)
Press the “
(Playback)” button to return to adjustment menu.
LDC
ON
LSC
ON
OIS
ON
Fig.
4-3-30
Click on the first or last page to see other DSC-H400 service manuals if exist.