Sony DSC-F828 (serv.man4) Service Manual ▷ View online
6-27
DSC-F828
16. CCD Black Defect Compensation Check
The positions of the black defective pixel are detected, and check
that the pixels can be corrected. And confirms that there is no trash
in the surface of the CCD imager, the optical filter and the inside of
the lens.
The positions of the black defective pixel are detected, and check
that the pixels can be corrected. And confirms that there is no trash
in the surface of the CCD imager, the optical filter and the inside of
the lens.
Mode
STILL (P AUTO) (P)
Subject
Clear chart (PTB-1450/PTB-450)
(Standard picture frame)
(Standard picture frame)
Measurement Point
Data of page: 60, address: 55
Measuring Instrument
Specified value 1
00 to 30
Specified value 2
00
Note1: Check that there are no dust, no dirt and no reflection on the clear
chart.
Note2: If the data of page: 60, address: 02 is “01”, select page: 60, address:
01, and Set data: 00.
Switch setting:
ZOOM ....................................................................... 70 (mm)
Adjusting method:
Order Page Address Data
Procedure
1
Check that “1. Data Setting
during Camera System
Adjustments” is performed.
during Camera System
Adjustments” is performed.
2
Check the picture frame. If
deviated, perform “5. or 6.
Picture Frame Setting”.
deviated, perform “5. or 6.
Picture Frame Setting”.
3
7D
65
Read the data, and memorize it.
4
7D
65
0A
Set the data.
5
60
2C
01
Set the data.
6
Rotate ZOOM ring and set the
ZOOM to “70” position.
ZOOM to “70” position.
7
60
92
00
Set the data.
8
60
93
00
Set the data.
9
60
01
79
Set the data.
10
60
30
08
Set the data.
11
Wait for 1 sec.
12
60
07
Read the data, and check it is “01”.
13
Check that the whole of the
screen is white.
screen is white.
14
60
01
8D
Set the data.
15
Wait for about 35 sec.
16
60
02
Read the data, and check it is
“01”.
“01”.
17
60
55
Read the data, and check it
satisfies the specified value 1.
If the data is “00”, proceed to
“Processing after Completing
Adjustments”
satisfies the specified value 1.
If the data is “00”, proceed to
“Processing after Completing
Adjustments”
18
60
01
00
Set the data.
19
Wait for 1 sec.
20
7D
65
0E
Set the data.
21
60
01
89
Set the data.
22
Wait for about 35 sec.
23
60
02
Read the data, and check it is “01”.
24
60
55
Read the data, and check it
satisfies the specified value 2.
satisfies the specified value 2.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
60
01
00
Set the data.
2
Wait for 1 sec.
3
60
2C
00
Set the data.
4
60
30
00
Set the data.
5
7D
65
Set the data memorized at
“Adjusting method”.
“Adjusting method”.
6
Save the data.
7
Wait for 2sec.
8
Set the ZOOM to WIDE end.
9
Perform next adjustments.
If finish the camera system
adjustments, release the data
setting.
(See “1. Data Setting during
Camera System Adjustments”.)
If finish the camera system
adjustments, release the data
setting.
(See “1. Data Setting during
Camera System Adjustments”.)
6-28
DSC-F828
17. Strobe Adjustment
Adjust the light level and white balance when the strobe light flashes.
Adjust the light level and white balance when the strobe light flashes.
Mode
STILL (P AUTO) (P)
Subject
Background paper (J-2501-130-A)
(50cm from the front of the lens)
(50cm from the front of the lens)
Measurement Point
Data of page 6F, address: DC
Measuring Instrument
Data of page 6E, address: 4F
Adjustment Page
6F
6E
Adjustment Address
D8 to EF
72 to 75
Specified Value1
03 to 09
Specified Value2
00
Note1: Perform this adjustment in the dark room or use the flash
adjustment box.
Note2: Any light other than the strobe light should not light up the plate.
Note3: After the power is turned on, this adjustment can be done only
Note3: After the power is turned on, this adjustment can be done only
once.
Note4: If the data of page: 60, address: 02 is “01”, select page: 60, address:
01, and set data: 00.
Switch setting:
ZOOM .................................................................... WIDE end
FLASH ......................................................................... OPEN
FLASH ......................................................................... OPEN
Adjusting method:
Order Page Address Data
Procedure
1
Check that “1. Data Setting
during Camera System
Adjustments” is performed.
during Camera System
Adjustments” is performed.
2
60
2C
01
Set the data.
3
60
92
FF
Set the data.
4
60
93
FF
Set the data.
5
60
6C
01
Set the data.
6
60
01
79
Set the data.
7
Wait for 5 sec.
8
60
07
Read the data, and check it is “01”.
9
6E
4F
FF
Set the data.
10
60
01
B9
Set the data.
11
Check the flashing.
12
60
02
Read the data, and check it is
“01”. (Note5)
“01”. (Note5)
13
6F
D8
Read the data, and check it is “00”.
14
60
01
00
Set the data.
15
Wait for 5 sec.
16
60
ED
Read the data, and check it is “02”.
17
Wait for 1 sec.
18
60
01
E7
Set the data.
19
Check the flashing.
20
60
02
Read the data, and check it is “01”.
21
6F
D8
Read the data, and check it is “00”.
22
6F
DC
Read the data, and check it
satisfies the specified value 1.
satisfies the specified value 1.
23
6E
4F
Read the data, and check it
satisfies the specified value 2.
satisfies the specified value 2.
Note5: The adjustment data will be automatically input to page: 6F,
address: D8 to EF, and to page: 6E, address: 72 to 75.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
60
01
00
Set the data.
2
60
2C
00
Set the data.
3
60
6C
00
Set the data.
4
60
92
00
Set the data.
5
60
93
00
Set the data.
6
If finish the camera system
adjustments, release the data
setting.
(See “1. Data Setting during
Camera System Adjustments”.)
adjustments, release the data
setting.
(See “1. Data Setting during
Camera System Adjustments”.)
6-29
DSC-F828
18. AF Laser Output Adjustment
Adjust the AF laser output power.
Adjust the AF laser output power.
Mode
STILL (P AUTO) (P)
Subject
Background paper (J-2501-130-A).
(50cm from the front of the lens)
(50cm from the front of the lens)
Measurement Point
Data of page 6F, address: 13
Measuring Instrument
Adjustment Page
6F
Adjustment Address
10 to 16
Specified Value
00
Note1: Perform this adjustment in the dark room or use the flash
adjustment box.
Note2: Any light other than the strobe light should not light up the plate.
Switch setting:
ZOOM .................................................................... WIDE end
Adjusting method:
Order Page Address Data
Procedure
1
Check that “1. Data Setting
during Camera System
Adjustments” is performed.
during Camera System
Adjustments” is performed.
2
6F
10
20
Set the data.
3
6F
15
48
Set the data.
4
60
01
AF
Write the data.
5
Check that the AF laser is lit.
6
Wait for 8 sec.
7
60
02
Read the data, and check it is
“01”. (Note3)
“01”. (Note3)
8
6F
13
Read the data, and check it
satisfies the specified value 1.
satisfies the specified value 1.
Note3: The adjustment data will be automatically input to page: 6F,
address: 10 to 16.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
60
01
00
Write the data.
2
If finish the camera system
adjustments, release the data
setting.
(See “1. Data Setting during
Camera System Adjustments”.)
adjustments, release the data
setting.
(See “1. Data Setting during
Camera System Adjustments”.)
6-30
DSC-F828
19. AF Laser Axis Check
Check the AF laser optical axis.
Check the AF laser optical axis.
Mode
STILL(P AUTO) (P)
Subject
Background paper (J-2501-130-A)
(1m from the front of the lens)
(1m from the front of the lens)
Measurement Point
Monitor TV (under scan)
Measuring Instrument
Specified Value
All hologram patterns are within the
inspection frame.
inspection frame.
Note1: Perform this adjustment in the dark room.
Preparations:
1)
1)
Take a copy of the AF Laser axis frame with a clear sheet.
(Reduce or enlarge the frame in same size as the effective picture
frame of the monitor TV.)
(Reduce or enlarge the frame in same size as the effective picture
frame of the monitor TV.)
Adjusting method:
Order Page Address Data
Procedure
1
Check that “1. Data Setting
during Camera System
Adjustments” is performed.
during Camera System
Adjustments” is performed.
2
60
30
06
Set the data.
3
60
2C
01
Set the data.
4
Set the ZOOM to WIDE end.
5
60
92
05
Set the data.
6
60
93
70
Set the data.
7
60
01
79
Write the data.
8
Wait for 3 sec.
9
60
07
Read the data, and check it is “01”.
10
60
01
00
Write the data.
11
60
22
05
Set the data.
12
60
23
0A
Set the data.
13
Check that all hologram patterns
are within the inspection frame.
(Fig. 6-1-15.)
are within the inspection frame.
(Fig. 6-1-15.)
14
Set the ZOOM to TELE end.
15
60
92
05
Set the data.
16
60
93
70
Set the data.
17
60
01
79
Write the data.
18
Wait for 3 sec.
19
60
07
Read the data, and check it is “01”.
20
60
58
01
Set the data.
21
60
14
8A
Set the data.
22
60
01
00
Write the data.
23
Check that all hologram patterns
are not unfocused.
are not unfocused.
Fig. 6-1-28.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
60
14
00
Set the data.
2
60
22
00
Set the data.
3
60
23
00
Set the data.
4
60
2C
00
Set the data.
5
60
30
00
Set the data.
6
60
58
00
Set the data.
7
60
92
00
Set the data.
8
60
93
00
Set the data.
9
If finish the camera system
adjustments, release the data
setting.
(See “1. Data Setting during
Camera System Adjustments”.)
adjustments, release the data
setting.
(See “1. Data Setting during
Camera System Adjustments”.)
Click on the first or last page to see other DSC-F828 (serv.man4) service manuals if exist.