Sony XR-F5005 Service Manual ▷ View online
5
XR-F5005
L
R
AUDIO OUT
REAR
*
2
REMOTE
IN
3
from car aerial
2
5
4
AMP REM
7
Left
Right
Left
Right
Max. supply current 0.3 A
Max. supply current 0.1 A
Fuse (10 A)
Red
Yellow
Black
Blue
Blue/white striped
White
Green
Purple
White/black striped
Grey/black striped
Green/black striped
Purple/black striped
Grey
3
1
ANT REM
6
*
3
Light blue
ATT
*
1
RCA pin cord (not supplied)
*
2
AUDIO OUT can be switched to REAR
or SUB.
For details, see the supplied operating
instructions.
or SUB.
For details, see the supplied operating
instructions.
*
3
Insert with the cord upwards.
*
1
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/MW/SW aerial in
the rear/side glass, connect the power aerial
control lead (blue) or the accessory power input
lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
control lead (blue) or the accessory power input
lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
• A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (
−) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker leads installed in your car if the unit shares
a common negative (
a common negative (
−) lead for the right and left
speakers.
• Do not connect the unit’s speaker leads to each
other.
Note on connection
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case, make
sure the speaker and amplifier are connected
correctly.
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case, make
sure the speaker and amplifier are connected
correctly.
6
XR-F5005
182 mm
53 mm
A
B
4
1
2
3
5
1
1
Dashboard
5
6
A
to dashboard/centre console
Bracket
Bracket
B
4
4
to dashboard/centre console
Bracket
Bracket
4
4
Existing parts supplied with your car
7
A
B
1
2
5
6
6
max. size
5
5
× 8 mm
max. size
5
5
× 8 mm
max. size
5
5
× 8 mm
max. size
5
5
× 8 mm
c
c
c
1
1
2
Face the hook inwards.
Claws
Orient the release key
correctly.
correctly.
Fire wall
2
3
c
Existing parts supplied with your car
7
XR-F5005
Precautions
• Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
driving operations.
• Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
temperatures, such as in direct sunlight or near
heater ducts.
• Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
Removing the protection collar
and the bracket (4)
and the bracket (4)
Before installing the unit, remove the
protection collar 5 and the bracket 1 from
the unit.
protection collar 5 and the bracket 1 from
the unit.
1
Remove the protection collar 5.
1 Engage the release keys 6 together with
1 Engage the release keys 6 together with
the protection collar 5.
2 Pull out the release keys 6 to remove the
protection collar 5.
2
Remove the bracket 1.
1 Insert both release keys 6 together
1 Insert both release keys 6 together
between the unit and the bracket 1 until
they click.
they click.
2 Pull down the bracket 1, then pull up the
unit to separate.
Frequency select switch
The AM (FM) tuning interval is factory-set to the
9 k (50 k) position. If the frequency allocation
system of your country is based on 10 kHz (200
kHz) interval, set the switch on the bottom of
the unit to the 10 k (200 k) position before
making connections.
9 k (50 k) position. If the frequency allocation
system of your country is based on 10 kHz (200
kHz) interval, set the switch on the bottom of
the unit to the 10 k (200 k) position before
making connections.
Mounting example (5)
Installation in the dashboard
Notes
• Bend these claws outwards for a tight fit, if
• Bend these claws outwards for a tight fit, if
necessary (5-2).
• Make sure that the 4 catches on the protection
collar 5 are properly engaged in the slots of the
unit (5-3).
unit (5-3).
Mounting the unit in a Japanese
car (6)
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 4.
To prevent malfunction, install only with the
supplied screws 4.
How to detach and attach the
front panel (7)
front panel (7)
Before installing the unit, detach the front
panel.
panel.
7
-A To detach
Before detaching the front panel, be sure to
press (OFF). Press (OPEN), then slide the front
panel to the right side, and pull out the left side.
press (OFF). Press (OPEN), then slide the front
panel to the right side, and pull out the left side.
7
-B To attach
Place the hole A in the front panel onto the
spindle B on the unit as illustrated, then push
the left side in.
spindle B on the unit as illustrated, then push
the left side in.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
without ACC (accessory)
position on the ignition key
switch
After turning off the ignition, be sure to
press and hold (OFF) on the unit until the
display disappears.
press and hold (OFF) on the unit until the
display disappears.
Otherwise, the display does not turn off and this
causes battery drain.
causes battery drain.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc., after detaching the
front panel.
completed, be sure to press the RESET button
with a ballpoint pen, etc., after detaching the
front panel.
XR-F5005
8
SECTION 2
DISASSEMBLY
Note:
Follow the disassembly procedure in the numerical order given.
2-2.
SUB PANEL SECTION
2
cover
4
two claws
6
flexible flat (14 core) cable
(CN701)
(CN701)
1
screw
(PTT2.6
(PTT2.6
×
6)
7
sub panel
section
section
5
two screws
(PTT2.6
(PTT2.6
×
6)
3
two claws
• This set can be disassembled in the order shown below.
2-1.
DISASSEMBLY FLOW
SET
2-2. SUB PANEL SECTION
(Page 8)
FRONT PANEL SECTION
Note: Illustration of disassembly is omitted.
Note: Illustration of disassembly is omitted.
2-4. MAIN BOARD
(Page 9)
2-3. MECHANISM DECK (MG-25L-136)
(Page 9)
Click on the first or last page to see other XR-F5005 service manuals if exist.