Sony XM-S400D Service Manual ▷ View online
XM-S400D
13
• IC Pin Function Description
MAIN BOARD IC508 R5F1037AANA (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
/RESET
I
Reset signal input terminal “L”: reset Fixed at “H” in this unit
2
BU_IN
I
Battery voltage detection signal input terminal “L”: over voltage
3
REM_IN
I
Remote detection signal input terminal “L”: remote on
4
SP_IN
I
Audio detection signal input terminal
5
Vss
-
Ground terminal
6
Vdd
-
Power supply terminal (+3.3V)
7
LED_ON
O
POWER PROTECT indicator LED drive signal output terminal “H”: LED on
8
AMP_STBY
O
Standby signal output to the power amplifi er “L”: standby
9
AMP_MUTE
O
Muting on/off control signal output to the power amplifi er “H”: muting on
10
AMP_FAULT
I
Fault detection signal input from the power amplifi er “L”: fault
11
AMP_SCL
O
I2C clock signal output to the power amplifi er
12
AMP_SDA
I/O
Two-way I2C data bus with the power amplifi er
13
INTP3
O
Muting on/off control signal output terminal “L”: muting on
14 to 17
NC
-
Not used
18
TEMP_POW1
I
Temperature measurement terminal Not used
19
TEMP_POW2
I
Temperature measurement terminal for power supply section (A/D input)
20
TEMP
I
Temperature measurement terminal (A/D input)
21
TEMP_AMP
I
Temperature measurement terminal for amplifi er section (A/D input)
22
MUTE
O
Muting control signal output terminal Not used
23
DCDC_ON
O
Power on/off control signal output terminal for DC/DC converter “H”: power on
24
TOOL0
I/O
Firmware update mode setting terminal “L”: update mode Fixed at “H” in this unit
14
XM-S400D
SECTION 5
EXPLODED VIEW
Note:
• -XX and -X mean standardized parts, so
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
original one.
• Items marked “
*” are not stocked since
they are seldom required for routine ser-
vice. Some delay should be anticipated
when ordering these items.
vice. Some delay should be anticipated
when ordering these items.
• The mechanical parts with no reference
number in the exploded views are not sup-
plied.
plied.
• Color Indication of Appearance Parts Ex-
ample:
KNOB, BALANCE (WHITE) . . . (RED)
Parts Color Cabinet’s Color
4
3
5
5
not supplied
1
2
2
3
3
3
3
3
2
2
not
supplied
supplied
not
supplied
supplied
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
FU1
MAIN board
Note:
When the complete MAIN board (Ref. No. 4) is replaced, be
sure to apply the grease (OIL COMPOUND (KS609)) so as to
cover the IC301 on the MAIN board.
sure to apply the grease (OIL COMPOUND (KS609)) so as to
cover the IC301 on the MAIN board.
1
3-971-322-01 SCREW
(2.6X8)
2
4-531-202-11 SCREW M2 (AL TYPE, OUTER) (L = 6 mm)
3
2-892-797-02 SCREW +PTW M2 (L = 3.5 mm)
4
A-2090-858-A MAIN BOARD, COMPLETE (See Note)
5
4-580-473-01 SHEET, HEAT TRANSFER (CHIP)
FU1
1-523-461-11 MINI FUSE (BLADE TYPE) (15 A/32 V)
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
15
XM-S400D
SECTION 6
ELECTRICAL PARTS LIST
A-2090-858-A MAIN BOARD, COMPLETE (See Note)
********************
< CONNECTOR >
CN101
1-843-527-11 PIN, CONNECTOR 10P (SIGNAL INPUT)
CN501
1-843-330-31 PIN, CONNECTOR 16P
< LED >
D514
6-504-260-01 LED 1L034XG42A0CAT01 (POWER PROTECT)
< FUSE >
FU1
1-523-461-11 MINI FUSE (BLADE TYPE) (15 A/32 V)
< IC >
IC301
6-721-943-01 IC TAS5414CTPHDRQ1 (See Note)
IC503
8-759-836-33 IC TL594CDTB-R2
IC507
6-722-640-01 IC NJM78L18UA-TE1
< FET >
Q513 6-553-668-01 FET
NTMFS5C646NL
Q514 6-553-668-01 FET
NTMFS5C646NL
< SWITCH >
S101
1-570-114-31 SWITCH, SLIDE (INPUT SELECT)
S102
1-570-114-31 SWITCH, SLIDE (REAR LPF)
S103
1-570-114-31 SWITCH, SLIDE (FRONT HPF)
************************************************************
ACCESSORIES
************
4-581-373-11 MANUAL, INSTRUCTION (ENGLISH, FRENCH,
GERMAN, SPANISH, DUTCH, SWEDISH,
ITALIAN, PORTUGUESE, POLISH, RUSSIAN,
ARABIC, PERSIAN, THAI) (U)
4-581-373-21 MANUAL, INSTRUCTION (ENGLISH) (IND)
************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS
**************************************
501
1-849-186-11 CONNECTION CABLE (Power connection cable)
502
1-849-187-11 RCA CABLE 200 mm (RCA input cord)
503
3-264-798-01 CAP (for RCA input cord) (1 piece)
504
1-849-185-11 CABLE (WITH CONNECTOR) 1 m
(High level input cord)
505
4-578-769-01 BRACKET FOOT (Bracket) (1 piece)
506
7-685-792-09 SCREW +PTT 2.6X6 (S) (Bracket screw) (1 piece)
507
4-238-407-12 SCREW (1) (4X20), +BV TAPPING
(Mounting screw) (1 piece)
POWER CONNECTION CABLE
u 1
RCA INPUT CORD
u 1
BRACKET
u 2
HIGH LEVEL INPUT CORD
u 1
MOUNTING SCREW
ø 4 mm
u 20 mm
u 2
BRACKET SCREW
ø 2.6 mm
u 6 mm
u 2
CAP
u 4
501
505
502
504
507
506
503
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
When indicating parts by reference num-
ber, please include the board name.
ber, please include the board name.
Only part of electrical parts that mounted
on the board of this unit can be replaced
for repair.
Since electrical parts that are not de-
scribed in the electrical parts list cannot be
replaced for repair, replace the complete
mounted board when these electrical parts
are defective.
on the board of this unit can be replaced
for repair.
Since electrical parts that are not de-
scribed in the electrical parts list cannot be
replaced for repair, replace the complete
mounted board when these electrical parts
are defective.
Note:
• Due to standardization, replacements in
• Due to standardization, replacements in
the parts list may be different from the
parts specifi ed in the diagrams or the com-
ponents used on the set.
parts specifi ed in the diagrams or the com-
ponents used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
original one.
• Items marked “*” are not stocked since
they are seldom required for routine ser-
vice. Some delay should be anticipated
when ordering these items.
vice. Some delay should be anticipated
when ordering these items.
• RESISTORS
All resistors are in ohms.
METAL:
All resistors are in ohms.
METAL:
Metal-fi lm resistor.
METAL OXIDE: Metal oxide-fi lm resistor.
F:
F:
nonfl ammable
• CAPACITORS
uF:
uF:
μF
• COILS
uH:
uH:
μH
• SEMICONDUCTORS
In each case, u: μ, for example:
uA.
In each case, u: μ, for example:
uA.
. :
μA. . , uPA. . , μPA. . ,
uPB.
.
:
μPB. . , uPC. . , μPC. . ,
uPD.
.
:
μPD. .
MAIN
Note: When the complete MAIN board or IC301 on the MAIN board are replaced, be sure to apply
the grease (OIL COMPOUND (KS609)) so as to cover the IC301 on the MAIN board.
XM-S400D
REVISION HISTORY
Ver.
Date
Description of Revision
1.0
2015.10
New
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
e.g.) If a contact point is shown as
, follow the procedure below.
Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.