Sony XAV-V630BT Service Manual ▷ View online
XAV-V630BT
9
4. Check Method of the NFC Tag Data
Check the NFC tag data according to the procedure below.
Check the NFC tag data according to the procedure below.
Procedure:
1. In the state of source off (Home screen is displayed), enter the
1. In the state of source off (Home screen is displayed), enter the
test mode by pressing the buttons on the remote commander in
order of the [4] t [5] t [0] (press only the [0] button for two
order of the [4] t [5] t [0] (press only the [0] button for two
seconds).
2. The following screen is displayed and confi rm the BT Addr
(Bluetooth address).
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
<Test Mode>
1.AUDIO FACTORY MODE
2.AUDIO DEBUG MODE
4.VISUAL FACTORY MODE
6.DESTINATION SETTING MODE
DEST: EUR REGION: 2
MCU: SONY-ST06-150721
Graphic: SONY-TW06-150721
Mecha: SONY-SP02-150721
Servo: HI6CD1-BBA-893D
BT: H28004-V2R133-20001 / XAV-V630BT
BT Addr: 001753767368
MCU: SONY-ST06-150721
Graphic: SONY-TW06-150721
Mecha: SONY-SP02-150721
Servo: HI6CD1-BBA-893D
BT: H28004-V2R133-20001 / XAV-V630BT
BT Addr: 001753767368
3. The resetting operation is executed by pressing the reset button
after the confi rming ends, and the unit returns to the normal
condition.
condition.
4. Turn on the NFC function of the smartphone.
5. Start the 15Visual NFCtagWriter application on the smart-
5. Start the 15Visual NFCtagWriter application on the smart-
phone.
6. Tap the “Read” on the screen of the smartphone.
15Visual NFCtagWriter
7. Check that “BD_ADDR” on the screen of the smartphone
accords with BD_ADDR confi rmed on the screen in the test
mode and “MODE” on the screen of the smartphone is “00 00
(Read-only)”.
mode and “MODE” on the screen of the smartphone is “00 00
(Read-only)”.
00 17 53 76 73 68
68 73 76 53 17 00
15Visual NFCtagWriter
8. End the 15Visual NFCtagWriter application on the smart-
phone.
5. The Factor that One Touch Connection is Impossible
The four following factors are considered as the factor that one touch connection is impossible.
Guess and check the defective factor by each checking result.
The four following factors are considered as the factor that one touch connection is impossible.
Guess and check the defective factor by each checking result.
Note:
The four following factors are examples.
Factor
Bluetooth manual con-
nection check by user
NFC tag data check
Bluetooth manual connec-
tion check by servicing
NFC one touch connection
check with smartphone
1
Complete BT
board defect
board defect
NG
―
NG
NG
2
VOL knob assy
defect
defect
OK
NG
OK
NG
3
NFC tag data
writing failure
writing failure
OK
NG
OK
NG
4 Smartphone
OK
OK
OK
NG
XAV-V630BT
10
6. Version Check Method of the NFC Tag Data Writing
Application for the Servicing
Check the version of the NFC tag data writing application
(15Visual NFCtagWriter application) for the servicing according
to the procedure below.
(15Visual NFCtagWriter application) for the servicing according
to the procedure below.
Procedure:
1. Start the 15Visual NFCtagWriter application on the smart-
1. Start the 15Visual NFCtagWriter application on the smart-
phone.
2. Tap the “ ” (menu button) or “ ” of the screen of the smart-
phone, then tap the “About” that is displayed on the screen of
the smartphone.
the smartphone.
15Visual NFCtagWriter
15Visual NFCtagWriter
or
3. Check that version of the NFC tag data writing application for
the servicing is displayed on the screen of the smartphone.
ver.1.2.0
2015
15Visual NFCtagWriter
NOTE FOR SECURITY FUNCTION
This unit does not use security function by password lock.
This unit does not use security function by password lock.
NOTE FOR BOARDS REPLACING
When the boards installed in this unit are defective, replace the
complete mounted board.
The mounted parts cannot replace with single.
When the boards installed in this unit are defective, replace the
complete mounted board.
The mounted parts cannot replace with single.
OPERATION CHECK OF THE NFC AFTER COMPLET-
ING THE REPAIRS (Except Indian and MARUTI SUZUKI
for SWIFT models only)
After completing the repairs of this unit, follow the procedure below
to check normal operation of the NFC.
ING THE REPAIRS (Except Indian and MARUTI SUZUKI
for SWIFT models only)
After completing the repairs of this unit, follow the procedure below
to check normal operation of the NFC.
Note: After checking of NFC operation, be sure to delete the pairing infor-
mation before returning this unit to the customer.
By touching the N-Mark on the unit with an NFC*
compatible smartphone, the unit is paired and
connected with the smartphone automatically.
compatible smartphone, the unit is paired and
connected with the smartphone automatically.
* NFC (Near Field Communication) is a technology
enabling short-range wireless communication
between various devices, such as mobile phones and
IC tags. Thanks to the NFC function, data
communication can be achieved easily just by
touching the relevant symbol or designated location
on NFC compatible devices.
between various devices, such as mobile phones and
IC tags. Thanks to the NFC function, data
communication can be achieved easily just by
touching the relevant symbol or designated location
on NFC compatible devices.
For a smartphone with Android OS 4.0 or lower
installed, downloading of the app “NFC Easy
Connect” available at Google Play™ is required. The
app may not be downloadable in some countries/
regions.
installed, downloading of the app “NFC Easy
Connect” available at Google Play™ is required. The
app may not be downloadable in some countries/
regions.
1
Activate the NFC function on the
smartphone.
smartphone.
For details, refer to the operating instructions
supplied with the smartphone.
supplied with the smartphone.
2
Touch the N-Mark part of the unit with
the N-Mark part of the smartphone.
the N-Mark part of the smartphone.
Make sure that lights up on the status bar of
the unit.
the unit.
Connecting with a smartphone by One
touch (NFC)
touch (NFC)
To disconnect by One touch
Touch the N-Mark part of the unit with the N-Mark
part of the smartphone again.
part of the smartphone again.
Notes
ˎ When making the connection, handle the
smartphone carefully to prevent scratches.
ˎ One touch connection is not possible when the unit is
already connected to another NFC compatible device.
In this case, disconnect the other device, and make a
connection with the smartphone again.
In this case, disconnect the other device, and make a
connection with the smartphone again.
XAV-V630BT
11
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
(US, CND)
Cautions
ˎ Run all ground (earth) leads to a common
ground (earth) point.
ˎ Do not get the leads trapped under a screw or
caught in moving parts (e.g., seat railing).
ˎ Before making connections, turn the car ignition
off to avoid short circuits.
ˎ Connect the yellow and red power supply leads
only after all other leads have been connected.
ˎ Be sure to insulate any loose unconnected leads
with electrical tape for safety.
ˎ Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
operations.
ˎ Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature,
such as in direct sunlight or near heater ducts.
such as in direct sunlight or near heater ducts.
ˎ Use only the supplied mounting hardware for a
safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component’s fuse amperage
rating.
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component’s fuse amperage
rating.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connection/Installation
Precautions
Connection
ʕ*
5
*
6
ʓ
Rear view camera*
1
Portable audio/
video device*
video device*
1
*
7
White
White/black striped
from a car antenna (aerial)
from a wired remote control (not
supplied)
supplied)
*4
*
3
*
3
*
3
Subwoofer*
1
Power amplifier*
1
For details, see “Making
connections” (page 35).
connections” (page 35).
Gray
Gray/black striped
Green
Green/black striped
Purple
Purple
Purple/black striped
Black
Yellow
Red
Blue/white striped
Orange/white striped
Light green
Purple/white striped
Black
Yellow
Red
Blue/white striped
Orange/white striped
Light green
Purple/white striped
*
3
*
3
*
3
Monitor*
1
Front speaker*
1
*
2
Rear speaker*
1
*
2
.
*1 Not supplied
*2 Speaker impedance: 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a
*2 Speaker impedance: 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a
wired remote control (not supplied).
For details on using the wired remote control, see
“Using the wired remote control” (page 36).
For details on using the wired remote control, see
“Using the wired remote control” (page 36).
*5 Whether in use or not, route the microphone input
cord so it does not interfere with driving operations.
Secure the cord with a clamp, etc., if it is installed
around your feet.
Secure the cord with a clamp, etc., if it is installed
around your feet.
*6 For details on installing the microphone, see
“Installing the microphone” (page 35).
*7 Such as a portable media player, game console, etc.
ɞ To a common ground (earth) point
First connect the black ground (earth) lead, then
connect the yellow and red power supply leads.
connect the yellow and red power supply leads.
ɟ To the +12 V power terminal which is
energized at all times
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
ɠ To the +12 V power terminal which is
energized when the ignition switch is set to
the accessory position
If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
the accessory position
If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
ɡ To the power antenna (aerial) control lead or
the power supply lead of the antenna (aerial)
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
ɢ To a car’s illumination signal
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
lead to a common ground (earth) point.
Making connections
.
.
ɣ To the parking brake switch cord
The mounting position of the parking brake
switch cord depends on your car.
Be sure to connect the parking brake lead (light
green) of the power supply connection cable ʓ
to the parking brake switch cord.
switch cord depends on your car.
Be sure to connect the parking brake lead (light
green) of the power supply connection cable ʓ
to the parking brake switch cord.
ɤ To the +12 V power terminal of the car’s rear
lamp lead (only when connecting the rear
view camera)
view camera)
Parking brake switch cord
Hand brake type
Foot brake type
Memory hold connection
When the yellow power supply lead is connected,
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
Speaker connection
ˎ Before connecting the speakers, turn the unit off.
ˎ Use speakers with an impedance of 4 to 8 ohms
and with adequate power handling capacities to
avoid damage.
avoid damage.
Monitor connection
When installing a monitor for the rear seat, connect
its parking brake switch cord to the ground (earth).
its parking brake switch cord to the ground (earth).
Note: The illustrations of this unit on this section might be different from the actual shape.
XAV-V630BT
12
To capture your voice during handsfree calling, you
need to install the microphone ʕ.
need to install the microphone ʕ.
Installing the microphone
ʖ
ʕ
Clip (not supplied)
ʕ
Installation
When mounting in a Japanese car, see “Mounting
the unit in a Japanese car” (page 37).
the unit in a Japanese car” (page 37).
Mounting the unit with an installation kit
(not supplied)
(not supplied)
Before installing, make sure the catches on both
sides of the bracket are bent inwards 3.5 mm (
sides of the bracket are bent inwards 3.5 mm (
5
/
32
in).
1
Position the bracket inside the
dashboard, then bend the claws outward
for a tight fit.
dashboard, then bend the claws outward
for a tight fit.
2
Mount the unit onto the bracket.
Note
If the catches are straight or bent outwards, the unit will
not be installed securely and may spring out.
If the catches are straight or bent outwards, the unit will
not be installed securely and may spring out.
Mounting the unit in the dashboard
Catch
Bracket
Larger than
182 mm (7
182 mm (7
1
/
4
in)
Larger than
111 mm (4
111 mm (4
3
/
8
in)
Bracket
Cautions
ˎ It is extremely dangerous if the cord becomes
wound around the steering column or gearstick.
Be sure to keep it and other parts from interfering
with your driving operations.
Be sure to keep it and other parts from interfering
with your driving operations.
ˎ If airbags or any other shock-absorbing
equipment are in your car, contact the store
where you purchased this unit, or the car dealer,
before installation.
where you purchased this unit, or the car dealer,
before installation.
Note
Before attaching the double-sided tape ʖ, clean the
surface of the dashboard with a dry cloth.
Before attaching the double-sided tape ʖ, clean the
surface of the dashboard with a dry cloth.
When using the steering wheel remote
control
control
Installation of the connection cable RC-SR1 (not
supplied) is required before use.
supplied) is required before use.
1
To enable the steering wheel remote control, select
[General Settings] q [User Defined] to make the
registration (page 19).
When the registration is complete, the steering
wheel remote control becomes available.
[General Settings] q [User Defined] to make the
registration (page 19).
When the registration is complete, the steering
wheel remote control becomes available.
Notes on installing the connection cable RC-SR1 (not
supplied)
supplied)
ˎ Refer to the support sites on the back cover for
details, then connect each lead properly to the
appropriate leads. Making an improper connection
may damage the unit.
appropriate leads. Making an improper connection
may damage the unit.
ˎ Consulting the dealer or an experienced technician
for help is recommended.
When using the wired remote control
1
To enable the wired remote control, set [Steering
Control] in [General Settings] to [Preset] (page 19).
Control] in [General Settings] to [Preset] (page 19).
Installation of the rearview camera (not supplied) is
required before use.
The image of a rearview camera connected to the
CAMERA IN terminal is displayed when:
required before use.
The image of a rearview camera connected to the
CAMERA IN terminal is displayed when:
ˋ the back lamp of your car lights up (or the shift
lever is set to the R (reverse) position).
ˋ you press HOME, then touch [Rear Camera].
ˋ you press and hold DSPL then touch [Rear
Camera] if [SOURCE Key Func.] is set to [DSPL]
Using the wired remote control
Using the rearview camera
.
.
.
.
When replacing the fuse, be sure to
use one matching the amperage
rating stated on the original fuse. If
the fuse blows, check the power
connection and replace the fuse. If
the fuse blows again after
replacement, there may be an
internal malfunction. In such a case, consult your
nearest Sony dealer.
use one matching the amperage
rating stated on the original fuse. If
the fuse blows, check the power
connection and replace the fuse. If
the fuse blows again after
replacement, there may be an
internal malfunction. In such a case, consult your
nearest Sony dealer.
Fuse replacement
Fuse (10 A)
Mounting the unit in a Japanese car
You may not be able to install this unit in some
Japanese cars. In such a case, consult your Sony
dealer.
Japanese cars. In such a case, consult your Sony
dealer.
When mounting this unit to the preinstalled
brackets of your car, use the supplied screws ʔ in
the appropriate screw holes based on your car: T
for TOYOTA, M for MITSUBISHI and N for NISSAN.
brackets of your car, use the supplied screws ʔ in
the appropriate screw holes based on your car: T
for TOYOTA, M for MITSUBISHI and N for NISSAN.
Note
To prevent a malfunction, install only with the supplied
screws ʔ.
To prevent a malfunction, install only with the supplied
screws ʔ.
ʔ
To the dashboard/center console
Parts supplied with your
car
car
ʔ
Bracket
Bracket
Click on the first or last page to see other XAV-V630BT service manuals if exist.