Sony XAV-V630BT Service Manual ▷ View online
XAV-V630BT
17
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
3-2. MINI FUSE (BLADE TYPE) (F1), COVER TOP
3-2. MINI FUSE (BLADE TYPE) (F1),
COVER
COVER
TOP
(Page
17)
3-3. FRONT PANEL BLOCK
(Page
(Page
18)
3-7. BT
BOARD
(Page
21)
3-6. BT MIC (CABLE) (BTM1)
(Page
(Page
20)
SET
3-5. BT
ANT
(ANT1),
FRONT PANEL ASSY (FP1)
(Page
20)
3-4. VOL KNOB ASSY, KEY BOARD
(Page
(Page
19)
2 screw
(PTT2.6
u 5)
1 mini fuse
(blade
type)
(F1)
3 two bosses
3 two bosses
4 four claws
4 claw
5 cover top
These are locked tightly.
These are not locked.
Note: When installing the cover top,
check that four bosses are all
locked.
OK
NG
XAV-V630BT
18
3-3. FRONT PANEL BLOCK
1 screw
(PTT2.6
u 5)
2 claw
1 two screws
(PTT2.6
u 5)
2 claw
2 two
claws
3 Remove the front panel block
in the direction of the arrow.
9 front panel block
4 sheet
(key
protection)
5 flexible flat
cable
2 claw
7 BT ANT
connector
6 filament tape
(sub
material)
8 Remove the BT ANT clamp
from the groove.
groove
Note 2: When installing the flexible
flat cable, align the position
of the boundary line of the
blue area and the white line
of the KEY board.
Insert is fully.
Insert is incomplete.
Tightly paste.
Loosely paste.
BT ANT
connector
connector
BT ANT
clamp
clamp
filament tape
(sub material)
(sub material)
BT board
OK
NG
OK
NG
touch panel flexible board
Note 1: Arrange the touch panel flexible
board as shown in the figure
below before installing the sheet
(key
protection).
KEY board
–
Right view
–
1 screw
(PTT2.6
u 5)
BT ANT wire setting
+Rw tR instDOO the IOe[iEOe
IODt FDEOe
IODt FDEOe
white line
+Rw tR instDOO the sheet Ne\ SrRteFtiRn
XAV-V630BT
19
3-4. VOL KNOB ASSY, KEY BOARD
–
Front panel block rear view
–
5 screw
(K
M2
u 3.5)
5 screw
(K
M2
u 3.5)
5 two screws
(K
M2
u 3.5)
7 claw
9 Draw the wire out from the hole
of the KEY board.
8 Remove the BT ANT wire from
the groove of the KEY board.
7 four claws
1 VOL knob assy
3 touch panel flexible board
4 LCD flexible board
6 screw
(B2
u 8)
6 two screws
(B2
u 8)
2 connector
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
How to install the flexible flat cable
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
KEY board
E7
Insert is shallow
Insert is straight
to the interior.
to the interior.
Note 2: When installing the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
Wire setting
OK
NG
hole
groove
0 KEY board
Note
3: When the KEY board is replaced, refer to
“FLICKER ADJUSTMENT” on page 22.
Note 1: When the VOL knob assy is replaced, Bluetooth information
writing is necessary. Refer to “BLUETOOTH INFORMA-
TION WRITING METHOD” on page 6. (Except IND and
IND2)
TION WRITING METHOD” on page 6. (Except IND and
IND2)
XAV-V630BT
20
3-6. BT MIC (CABLE) (BTM1)
1 Remove the BT MIC cable
from two lead pins.
4 BT MIC (cable)
(BTM1)
groove
3 Remove the clamp from the groove.
Note: When installing the BT
MIC (cable), check that
clamp is not damaged.
–
Rear view
–
%7 0,& FaEOe VeWWiQJ
clamp
two lead pins
MAIN board
BT board
connector
BT MIC (cable)
(BTM1)
(BTM1)
front side
rear side
clamp
front side
rear side
2 BT MIC cable
connector
BT board
3-5. BT ANT (ANT1), FRONT PANEL ASSY (FP1)
groove
–
Front panel block rear view
–
3 BT ANT (ANT1)
2 Remove the BT ANT clamp
from the groove.
BT ANT clamp
BT ANT (ANT1)
cushion
top side
bottom side
+ow to inVtall tKe %7 $17 $17
BT ANT clamp
groove
4 front panel assy (FP1)
1 cushion
Note
2: The front panel assy for repair
includes a cushion.
When replacing the front panel
assy, remove the cushion,
install the BT ANT, and then
install the cushion.
Note 1: When the front panel assy (Ref. No. FP1) is replaced, refer to
“FLICKER ADJUSTMENT” on page 22.
Click on the first or last page to see other XAV-V630BT service manuals if exist.