Sony XAV-V630BT Service Manual ▷ View online
XAV-V630BT
21
3-7. BT BOARD
5 Remove the BT board
in the direction of the
arrow.
2 connector
1 Remove the wire
from two hooks.
:LUHVHWWLQJ
MAIN board
BT board
two hooks
3 Remove two solders.
4 Bent claw is returned
to a straight form.
4 Bent claw is returned
to a straight form.
–
5HDUYLHZ
–
front side
rear side
6 BT board
Note 1: When the BT board is replaced, be sure to replace the VOL
knob assy simultaneously. (Except IND and IND2)
Note 2: When the BT board is replaced, Bluetooth information writ-
ing is necessary. Refer to “BLUETOOTH INFORMATION
WRITING METHOD” on page 6. (Except IND and IND2)
WRITING METHOD” on page 6. (Except IND and IND2)
Note 3: When the BT board is replaced, replaced old BT board is de-
stroyed with the hammer, and throw out it.
XAV-V630BT
22
SECTION 4
ELECTRICAL ADJUSTMENT
MONITOR SECTION
If any of the following parts was replaced, execute the “Flicker
Adjustment” as mentioned below.
• CHASSIS MAIN ASSY (Including MAIN board)
• FRONT PANEL ASSY (Including LCD module, Touch panel)
• COMPLETE KEY BOARD
Adjustment” as mentioned below.
• CHASSIS MAIN ASSY (Including MAIN board)
• FRONT PANEL ASSY (Including LCD module, Touch panel)
• COMPLETE KEY BOARD
Preparation:
• Remote commander (RM-X170)
• Remote commander (RM-X170)
FLICKER ADJUSTMENT
1. Turn the power on, and perform the aging more than fi ve min-
1. Turn the power on, and perform the aging more than fi ve min-
utes.
2. In the state of source off (Home screen is displayed), pressing
the buttons on the remote commander in order of the [4]
→ [5]
→ [4] (press only the [4] button for two seconds).
The test mode 4 starts, and the following screen is displayed on
the monitor.
the monitor.
(Displayed colors/values in the following fi gure are example)
PAL_SEL:0
SWAP:0
VCOM:064
SWAP:0
VCOM:064
TEST 4
3. Press the [B] button on the remote commander to set the
“PAT_SEL:9”.
4. Press the [b] button on the remote commander to set the
“SWAP:0”.
5. Press the [V] or [v] button on the remote commander to adjust
so that the fl icker becomes minimum in the sight.
(There is a point most suitable in the range of VCOM:045 to
VCOM:090)
VCOM:090)
The relation between the fl icker and the adjustment value has
the characteristic such as the following fi gure.
the characteristic such as the following fi gure.
Example of characteristic:
Flicker
VCOM value
bad
o
m
good
6. Press the [PUSH SOURCE/ VOICE] button on the main unit,
and turn the power off.
23
XAV-V630BT
SECTION 5
EXPLODED VIEW
Note:
• -XX and -X mean standardized parts, so
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
original one.
• Items marked “*” are not stocked since
they are seldom required for routine ser-
vice. Some delay should be anticipated
when ordering these items.
vice. Some delay should be anticipated
when ordering these items.
• The mechanical parts with no reference
number in the exploded views are not sup-
plied.
plied.
• Color Indication of Appearance Parts Ex-
ample:
KNOB, BALANCE (WHITE) . . . (RED)
Parts Color Cabinet’s Color
not supplied
CHA1
2
2
FP1
NFC1
ANT1
1
2
2
3
4
4
4
5
6
F1
PW1
BTM1
not supplied
not supplied
#1
#1
#1
#1
#1
#1
(IND, IND2)
(Except IND, IND2)
Note 1: When the complete BT board (Ref. No. 6) or VOL
knob assy (Ref. No. NFC1) are replaced, Bluetooth
information writing is necessary. Refer to “BLUE-
TOOTH INFORMATION WRITING METHOD”
on page 6. (Except IND and IND2)
information writing is necessary. Refer to “BLUE-
TOOTH INFORMATION WRITING METHOD”
on page 6. (Except IND and IND2)
Note 2: When the complete KEY board (Ref. No. 3), chassis
main assy (Ref. No. CHA1) or front panel assy (Ref.
No. FP1) are replaced, refer to “FLICKER ADJUST-
MENT” on page 22.
No. FP1) are replaced, refer to “FLICKER ADJUST-
MENT” on page 22.
Note 3: When the complete BT board (Ref. No. 6) is re-
placed, replaced old complete BT board is destroyed
with the hammer, and throw out it.
with the hammer, and throw out it.
Note 4: When the chassis main assy (Ref. No. CHA1) is replaced, re-
fer to “DESTINATION SETTING METHOD” on page 4.
Note 5: When the complete BT board (Ref. No. 6) is replaced, be sure
to replace the VOL knob assy (Ref. No. NFC1) simultane-
ously. (Except IND and IND2)
ously. (Except IND and IND2)
1
A-2087-420-A VOL KNOB ASSY (IND, IND2)
2
9-885-192-54 SCREW +K M2X3.5 (EP-FE/ZNBK/CM)
3
A-2087-421-A KEY BOARD, COMPLETE (US, CND) (See Note 2)
3
A-2087-422-A KEY BOARD, COMPLETE (AEP, UK, E (NTSC),
E (PAL), IND) (See Note 2)
3
A-2087-904-A KEY BOARD, COMPLETE (IND2) (See Note 2)
4
9-885-204-56 SCREW +B 2X8 TYPE2 (EP-FE/ZNBK)
5
9-885-192-50 SHEET (PROTECTION, KEY)
6
A-2087-410-A BT BOARD, COMPLETE (See Note 1, 3, 5)
ANT1 9-885-197-32 BT
ANT
BTM1
9-885-197-33 BT MIC (CABLE)
CHA1
A-2087-400-A CHASSIS MAIN ASSY (Including MAIN board,
Flexible fl at cable) (US, CND) (See Note 2, 4)
CHA1
A-2087-401-A CHASSIS MAIN ASSY (Including MAIN board,
Flexible fl at cable) (AEP, UK, E (NTSC),
E (PAL), IND) (See Note 2, 4)
CHA1
A-2087-901-A CHASSIS MAIN ASSY (Including MAIN board,
Flexible fl at cable) (IND2) (See Note 2, 4)
F1
9-885-192-49 MINI FUSE (BLADE TYPE) (10 A)
FP1
A-2087-412-A PANEL ASSY, FRONT (Including LCD module,
Touch panel) (E (NTSC)) (See Note 2)
FP1
A-2087-413-A PANEL ASSY, FRONT (Including LCD module,
Touch panel) (Except E (NTSC)) (See Note 2)
NFC1
A-2087-419-A VOL KNOB ASSY (Including NFC module)
(Except IND, IND2) (See Note 1, 5)
PW1
1-846-035-11 CONNECTION CABLE (ISO) (POWER) (AEP, UK)
PW1
1-846-039-11 CONNECTION CABLE, AUTOMOBILE (POWER)
(US, CND, E (NTSC), E (PAL), IND)
PW1
9-885-203-91 CORD (WITH CONNECTOR) (POWER) (IND2)
#1
7-685-791-01 SCREW +PTT 2.6X5 (S)
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
XAV-V630BT
24
SECTION 6
ACCESSORIES
ACCESSORIES
************
1-487-638-13 REMOTE COMMANDER (RM-X170) (E (NTSC),
IND, IND2)
4-577-696-12 MANUAL,
INSTRUCTION
(ENGLISH, FRENCH, SPANISH) (US, CND)
4-577-696-22 MANUAL, INSTRUCTION (ENGLISH, SPANISH)
(E (NTSC))
4-577-696-32 MANUAL, INSTRUCTION (ENGLISH) (E (PAL),
IND, IND2)
4-577-696-42 MANUAL, INSTRUCTION (ARABIC, PERSIAN)
(E (PAL))
4-577-696-52 MANUAL,
INSTRUCTION
(ENGLISH, SPANISH, ITALIAN) (AEP, UK)
4-577-696-62 MANUAL,
INSTRUCTION
(FRENCH, GERMAN, DUTCH) (AEP, UK)
************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS
**************************************
501
X-2588-296-1 FITTING FRAME ASSY (AEP, UK)
502
4-464-557-01 TRIM-PLATE (AEP, UK)
503
4-479-204-01 RELEASE KEY (1 piece) (AEP, UK)
504
3-934-325-21 SCREW, +K (5X8) TAPPING (1 piece)
505
1-846-035-11 CONNECTION CABLE (ISO) (POWER) (AEP, UK)
505
1-846-039-11 CONNECTION CABLE, AUTOMOBILE (POWER)
(US, CND, E (NTSC), E (PAL), IND)
505
9-885-203-91 CORD (WITH CONNECTOR) (POWER) (IND2)
506
A-2018-274-A COLLAR ASSY (IND, IND2)
507
1-542-986-11 MICROPHONE UNIT (Including Double-sided tape)
POWER CORD (ISO)
u1
505
505
506
504
POWER CORD
u1
505
POWER CORD
u1
COLLAR ASSY
u1
+K5
u8
u6
MICROPHONE UNIT
u1
MICROPHONE
u1
DOUBLE-SIDED TAPE
u1
507
(IND, IND2)
501
503
FITTING FRAME ASSY
u1
502
TRIM PLATE
u1
RELEASE KEY
u2
(AEP, UK)
(AEP, UK)
(US, CND, E (NTSC),
E (PAL), IND)
E (PAL), IND)
(IND2)
Click on the first or last page to see other XAV-V630BT service manuals if exist.