Sony XAV-601BT Service Manual ▷ View online
XAV-601BT
25
3-14. CHASSIS (OP, ZA) COMPLETE ASSY (OP1)
xxxxxxxxxxx
A
5
6 two coil springs
(damper)
9 chassis (OP, ZA) complete assy (OP1)
8 label (S)
7 compression spring
(damper,
Z)
2 sled motor flexible board
(CN1)
3 tension spring (KF)
tension spring (KF)
0HWKRGRILQVWDOOLQJWHQVLRQVSULQJ.)
4 Turn the gear (RA1) fully
in the direction of arrow
A.
Hang in order of
A, B by pay
attention spring of direction.
A
B
±%RWWRPYLHZ±
1 OP flexible board (CN2)
Note:
When disconnecting the OP flexible board
from of the connector. Be sure to refer to
“NOTE FOR FLEXIBLE BOARD OF THE
OPTICAL PICK-UP” of the servicing notes
(See page 6).
3-15. PANEL (BACK) BLOCK
3 screw (M2)
(2
u 8, Black)
3 screw (M2)
(2
u 8, Black)
3 screw (M2)
(2
u 8, Black)
2 two screws
(S1.7
u 4)
1 two sheets (screw)
2 three screws
(S1.7
u 4)
8 button
(release)
7 spring
(release)
5 six claws
1 three sheets
(screw)
9 panel (back) block
4 screw (T)
(2
u 4, Black)
4 screw (T)
(2
u 4, Black)
4 two screws (T)
(2
u 4, Black)
6
– Front panel block rear side view –
OK
NG
sheet (screw)
sheet (screw)
Note: If the installation position of a screw (T) and a screw (M2) is mistaken, liquid
crystal display panel (LCD1) and touch panel (TPN1) are sometimes damaged.
Be sure to install after checking the kind and installation position of a screw.
XAV-601BT
26
3-16. D-SUB6 BOARD
3-17. KEY6 BOARD
3 screw (B)
3 screw (B)
2 sheet (lock assy)
1 two shafts
3 screw (B)
6 D-SUB6 board
4 Remove the solder.
5 plate (GND)
– Back panel block front side view –
3 screw (T) (2 u 4, Silver)
2 flexible flat cable (20 core)
(CN2501)
1 knob (VOL) (SV) assy
4 KEY6 board
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
flexible
cable
cable
connector
flexible
cable
cable
connector
flexible
cable
cable
NG
OK
NG
Note: When you install the flexible flat cable (20 core), please install
it correctly. There is a possibility that this machine damages
when not correctly installing it.
– Front panel block rear side view –
XAV-601BT
27
4 flexible flat cable (10 core)
(CN4600)
3 flexible flat cable (60 core)
(CN4000)
2 touch panel flexible board
(CN4500)
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
flexible
cable
cable
connector
flexible
cable
cable
connector
flexible
cable
cable
NG
OK
NG
Note 2: When you install the LCD flexible board, the touch panel
flexible board and the flexible flat cable (20 core), please
install them correctly. There is a possibility that this
machine damages when not correctly installing it.
B
C
– Front panel block rear side view –
6 chassis (display6) block
5 two claws
5 claw
5 claw
5 claw
B
C
1 filament tape
filament tape
:ire settinJ
DISP board
3-18. CHASSIS (DISPLAY6) BLOCK
Note 1: When complete DISP board is exchanged, exchanged old complete
DISP board and is destroyed with the hammer, and throw out it.
XAV-601BT
28
3-19. DISP BOARD
– Front panel block rear side view –
4
6 DISP board
1 screw (T) (
2
u 4, Silver)
5 shield (AP) block
1 three screws (T)
(
2
u 4, Silver)
2 Remove the solder.
3 Bend the claw in the
direction of an arrow.
shield (AP) block
DISP board
total eight lock
lock
unlock
NG
OK
Note: Check that the mark of the shield (AP) and the
mark of the DISP board are the same directions.
+RZWRLQVWDOOWKHVKLHOG$3EORFN
Click on the first or last page to see other XAV-601BT service manuals if exist.