Sony MEX-XB100BT Service Manual ▷ View online
MEX-XB100BT
29
3-8. AMP BOARD
(US, CND)
5 screw
(PTT2.6
(PTT2.6
u 6)
5 screw
(PTT2.6
(PTT2.6
u 6)
1 two screws
(PTT2.6
(PTT2.6
u 6)
qs AMP board
8 heat transfer
IC
IC
sheet
9 Remove the solder.
9 Remove the solder.
qa bracket AMP
0 Remove the solder.
2 three screws
(PTT2
(PTT2
u 10)
6 screw
(P2.6
(P2.6
u 8)
7 chassis back
3 heat sink
– MAIN board block rear view –
– MAIN board block left view –
+RZWRLQVWDOOWKHVFUHZV
+HDWWUDQVIHU,&VKHHWVHWWLQJ
short (21.1 mm)
heat transfer IC sheet
long
(24.1 mm)
OK
NG
short
(21.1 mm)
long (24.1 mm)
guide line
MAIN board
MAIN board
heat sink
chassis back
claw
corner
connector
(CN1600)
(CN1600)
corner
claw
claw
claw
claw
groove
claw
AMP board
heat transfer IC sheet
heat transfer IC sheet
,QVWDOOLQJWKHFKDVVLVEDFN
4 Remove the solder.
5
&RQQHFWRU&1VHWWLQJ
chassis back
MAIN board
claw
claw
– MAIN board block rear bottom view –
Solder the hook to
the MAIN board.
the MAIN board.
connector (CN1600)
$SSOLFDWLRQSRVLWLRQRIJUHDVH
OIL COMPOUND (KS609)
IC1600
Note 1: When installing the screws in
the order shown below.
Note 2: When replacing the AMP board,
it is necessary to spread the grease.
Spread the grease over the IC1600
referring to the figure below.
4
2
3
1
0 Remove the
solder.
solder.
–
$03ERDUGEORFNULJKWYLHZ–
%UDFNHW$03VHWWLQJ
Solder the bracket AMP
and AMP board.
and AMP board.
AMP board
bracket AMP
front
side
side
MEX-XB100BT
30
3-9. TUNER UNIT (TUX-DSP04)
3-10. HOW TO INSTALL THE KNOB (VOL) (SV) ASSY
:LUHVHWWLQJ
tuner unit
(TUX-DSP04)
(TUX-DSP04)
wire
J001
MAIN board
1 Remove the solder.
3 tuner unit
(TUX-DSP04)
(TUX-DSP04)
2 Remove the solder.
Note 1: When the knob (VOL) (SV) assy is replaced, Bluetooth informa-
tion writing is necessary. Refer to“BLUETOOTH INFORMA-
TION WRITING METHOD” on page 9.
TION WRITING METHOD” on page 9.
2 Align two shafts and two grooves.
Since the position of the groove to rotate, check
the position of the groove when attach the shaft.
3 Confirm a top and bottom
direction of NFC logo.
4 Push until the clicking sound is heard.
knob (VOL) (SV) assy
front panel assy
cushion
(knob)
(knob)
1 Make sure that the cushion (knob) is installed
correctly.
Note 2: When pushed by a strong force there is a risk
of damage to the inside of the switch.
Push in the appropriate force, be careful not
to push too strongly.
OK
NG
knob
(VOL)
(VOL)
cushion
(knob)
(knob)
knob
(VOL)
(VOL)
two shafts
two grooves
MEX-XB100BT
31
3-11. SERVICE POSITION
Note 1:
The service position below cannot be performed with the fl exible
fl at cable (length: 90 mm) used with the unit. Refer to “NOTE OF
PERFORMING THE OPERATION CHECK” in the servicing
notes, and use a long fl exible fl at cable (length: 150 mm).
fl at cable (length: 90 mm) used with the unit. Refer to “NOTE OF
PERFORMING THE OPERATION CHECK” in the servicing
notes, and use a long fl exible fl at cable (length: 150 mm).
CD mechanism deck
Note 2: Do not put a CD mechanism deck
Note 2: Do not put a CD mechanism deck
near the heat sink in the left side
of the main unit.
CD mechanism deck
insulating sheet
insulating sheet
stand
stand
main unit
main unit
cable flexible flat (27 core)
(length: 150 mm)
(length: 150 mm)
cable flexible flat (27 core)
(length: 150 mm)
(length: 150 mm)
main unit
main unit
cable flexible flat (27 core)
(length: 150 mm)
(length: 150 mm)
cable flexible flat (27 core)
(length: 150 mm)
(length: 150 mm)
CD mechanism deck
Note 3: CD mechanical deck should
Note 3: CD mechanical deck should
not be placed vertically.
CD mechanism deck
Note 3: CD mechanical deck should
Note 3: CD mechanical deck should
not be placed vertically.
main unit
cable flexible flat (27 core)
(length: 150 mm)
(length: 150 mm)
Do not touch a heat sink.
CD mechanism deck
Note 4: CD mechanical deck should
Note 4: CD mechanical deck should
not be placed upside down.
Do not touch a heat sink.
OK
NG
NG
NG
NG
MEX-XB100BT
32
SECTION 4
TEST MODE
SETTING THE TEST MODE
Setting method:
1. In the state of source off (the clock is displayed), enter the test
1. In the state of source off (the clock is displayed), enter the test
mode by pressing the buttons in order of the [
4]
t [MIC
5]
t [V
ALBUM 1] (press only the [V
ALBUM 1] button for
two seconds).
2. It is set to the test mode, and all segments of the liquid crystal
display light.
Releasing method:
Press the [
Press the [
OFF SRC] button for 1 second.
MICROPHONE AUDIO LOOPBACK
To confi rm the state of the external microphone used when a
handsfree function is used, the microphone audio is output from
the speaker.
The breakdown judgment of the microphone can be done without
connecting H/F with the cellular phone.
To confi rm the state of the external microphone used when a
handsfree function is used, the microphone audio is output from
the speaker.
The breakdown judgment of the microphone can be done without
connecting H/F with the cellular phone.
Procedure:
1. Enter the test mode.
2. Press the [
1. Enter the test mode.
2. Press the [
OFF SRC] button to select the Bluetooth Phone
function.
3. On/off of the microphone audio loopback function changes
whenever the [ALBUM v
2] button is pressed (“0” is dis-
played on the liquid crystal display).
LOOPBACK
DISPLAY
ON
BTP 0
OFF
BTP
Click on the first or last page to see other MEX-XB100BT service manuals if exist.